Investigation of high-cycle fatigue and fatigue crack propagation characteristic in 5083-O aluminum alloy
Source abstract
Abstract
Abstract The objective of the present study is to investigate the high-cycle fatigue (HCF) and fatigue crack propagation (FCP) characteristic in relation to the microstructure in the 5083-O aluminum alloy. The HCF strengths of the 5083-O Al alloy in parallel to rolling direction (PD) and vertical to rolling direction (VD) specimens are 164 MPa and 165 MPa, respectively, However, the FCP resistance of the specimens reveals evident anisotropy. The FCP resistance of the PD specimen is less than that of the VD specimen, which is predominantly caused by the main crack expanding along the chain-shaped coarse inclusions in PD specimen. These chain-shaped coarse inclusions, particularly, Fe/Mn containing particles with secondary microcracks, might accelerate FCP rate and decrease FCP resistance.
Source: openaire · Quality: candidate unverified · Source record ↗
Research context
OpenAlex topics: Fatigue and fracture mechanics · Aluminum Alloy Microstructure Properties · High Temperature Alloys and Creep
SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.
References (79)
Show source-provided references
1. Semi-quantitative evaluation of texture components and anisotropy of the yield strength in 2524 T3 alloy sheets10.1016/j.msea.2016.08.013 ↗
2. The precipitation behavior and mechanical properties of cast Al-4.5Cu-3.5Zn-0.5Mg alloy10.1016/j.jallcom.2018.07.172 ↗
3. Effect of aging time on the microstructure evolution and mechanical property in an Al-Cu-Li alloy sheet10.1016/j.msea.2018.10.064 ↗
4. The influence of sensitization and corrosion on creep of 5083–H11610.1016/j.corsci.2018.07.036 ↗
5. Control of second-phase particles in the Al-Mg-Mn alloy AA 508310.1016/j.jallcom.2016.08.070 ↗
6. Ultrafine versus coarse grained Al 5083 alloys: from low-cycle to very-high-cycle fatigue10.1016/j.ijfatigue.2018.12.004 ↗
7. Potential fatigue strength improvement of AA 5083–H111 notched parts by wire brush hammering: experimental analysis and numerical simulation10.1016/j.matdes.2014.08.002 ↗
8. Microstructure analysis and low-cycle fatigue behavior of spray-formed Al–Li alloy 2195 extruded plate10.1016/j.msea.2018.11.053 ↗
9. Improving the fatigue strength of 7075 alloy through aging10.1016/j.msea.2018.09.047 ↗
10. Analytical fatigue life prediction of shot peened AA 7050–T745110.1016/j.ijfatigue.2018.07.007 ↗
11. Influence of surface treatments on surface layer properties, fatigue and corrosion fatigue performance of AA7075 T7310.1016/j.matdes.2012.04.056 ↗
12. Effect of surface roughness on corrosion fatigue performance of AlSi10Mg alloy produced by Selective Laser Melting (SLM)10.1016/j.matchar.2017.06.029 ↗
13. A gradient-based multiaxial criterion for fatigue crack initiation prediction in components with surface roughness10.1016/j.ijfatigue.2018.08.020 ↗
14. The effects of laser shock peening scanning patterns on residual stress distribution and fatigue life of AA2024 aluminium alloy10.1016/j.optlastec.2018.06.036 ↗
15. Effect of compressive residual stress generated by plastic preload on fatigue initiation of 6061 Al-alloy
16. Influence of the cold-drawing process on fatigue crack growth of a V-notched round bar10.1016/j.ijfatigue.2009.12.014 ↗
17. Experimental study of the impact of geometrical defects on the high cycle fatigue behavior of polycrystalline aluminium with different grain sizes10.1016/j.ijfatigue.2017.12.009 ↗
18. Effects of an artificial small defect on torsional fatigue strength of steels10.1115/1.3225951 ↗
19. Influence of the crack morphology on the fatigue crack growth rate: a continuously-kinked crack model based on fractals10.1016/j.engfracmech.2007.05.007 ↗
20. Effect of environment on fatigue crack growth in ultrafine grain Al–Mg10.1016/j.ijfatigue.2009.03.018 ↗
21. Effect of corrosive environment on fatigue property and crack propagation behavior of Al 2024 friction stir weld10.1016/S1003-6326(16)64411-4 ↗
22. Frequency effect and influence of testing technique on the fatigue behaviour of quenched and tempered steel and aluminium alloy10.1016/j.ijfatigue.2016.05.013 ↗
23. Dauerfestigkeit - eine Fiktion
24. Enhanced fatigue crack propagation resistance of an Al–Cu–Mg alloy by artificial aging under influence of electrical field10.1016/j.msea.2010.03.011 ↗
25. The behavior of fatigue crack initiation and propagation in AA2524-T34 alloy10.1016/j.msea.2010.10.085 ↗
26. Characterization of high cycle fatigue behavior of a new generation aluminum lithium alloy10.1016/j.actamat.2011.06.003 ↗
27. Semi-quantitative evaluation of texture components and fatigue properties in 2524 T3 aluminum alloy sheets10.1016/j.msea.2016.01.026 ↗
28. Grain size dependence of fatigue properties of friction stir processed ultrafine-grained Al-5024 alloy10.1016/j.ijfatigue.2017.12.007 ↗
29. A crystallographic mechanism for fatigue crack propagation through grain boundaries10.1016/S1359-6454(00)00214-7 ↗
30. Effect of grain boundary misorientaton, deformation temperature and AlFeMnSi-phase on fatigue life of 6082 Al alloy10.1016/j.matchar.2017.01.002 ↗
31. Probabilistic modeling of fatigue related microstructural parameters in aluminum alloys10.1016/j.engfracmech.2008.09.005 ↗
32. Effects of constituent particle clusters on fatigue behavior of 2024–T3 aluminum alloy10.1016/S0142-1123(98)00041-3 ↗
33. A study of nucleation and fatigue behavior of an aerospace aluminum alloy 2024–T310.1016/j.ijfatigue.2004.06.010 ↗
34. The cyclic fatigue and final fracture behavior of aluminum alloy 252410.1016/S0261-3069(01)00070-X ↗
35. Effects of inclusions, grain boundaries and grain orientations on the fatigue crack initiation and propagation behavior of 2524–T3 Al alloy10.1016/j.msea.2013.05.053 ↗
36. The effect of constituent particles in aluminum alloys on fatigue damage evolution: statistical observations10.1016/j.ijfatigue.2009.02.036 ↗
37. Thermodynamic assessment of the aluminum corner of the Al-Fe-Mn-Si system10.1007/s11661-010-0263-x ↗
38. Effect of second phase particles on grain refinement during equal-channel angular pressing of an Al-Mg-Mn alloy10.1016/j.actamat.2011.10.023 ↗
39. Study of β precipitation and layer structure formation in Al 5083: the role of dispersoids and grain boundaries10.1016/j.jallcom.2017.01.360 ↗
40. Investigation of pre-existing particles in Al 5083 alloys10.1016/j.jallcom.2017.12.329 ↗
41. Impact of homogenization on particles in the Al-Mg-Mn alloy AA 5454 – experiment and simulation10.1016/j.jallcom.2013.01.163 ↗
42. Metallography of fatigue crack initiation in an overaged high-strength aluminum alloy10.1007/BF02644299 ↗
43. The effect of intermetallics composition and microstructure on fatigue crack initiation in AI 2219–T85110.1007/BF02652263 ↗
44. Microstructural effects on the small fatigue crack behaviour of an aluminum alloy plate10.1111/j.1460-2695.1995.tb00905.x ↗
45. Micromechanisms of multistage fatigue crack growth in a high-strength aluminum alloy10.1016/j.actamat.2006.11.009 ↗
46. Oswald LE. Effects of microstructure on high-cycle fatigue of an Al-Zn-Mg-Cu alloy (Al-7055). University of Pittsburgh; 2003.
47. Observations of fatigue crack initiation in 7075–T65110.1016/j.ijfatigue.2009.06.003 ↗
48. Enhanced low-cycle fatigue and crack propagation resistance of an Al-Cu-Mg-Si forging alloy by non-isothermal aging10.1016/j.msea.2018.07.002 ↗
49. Anisotropy in fatigue crack propagation behavior of Al-Cu-Li alloy thick plate10.1016/j.matchar.2017.07.025 ↗
50. Effect of anisotropy on fatigue properties of 2198 Al–Li plates joined by friction stir welding10.1016/j.engfailanal.2008.09.024 ↗
51. The anisotropy of fatigue crack nucleation in an AA7075 T651 Al alloy plate10.1016/j.msea.2014.11.007 ↗
52. ISO 12107–2003: metallic materials-Fatigue testing-Statistical planning and analysis of data.
53. Lassociation Francaise de Normalisation · 1991
54. JSME S 002–1981: standard method of statistical fatigue testing.
55. BS 3518–1966: Methods of fatigue testing, part 5 – guide to the application of statistics.
56. A method for obtaining and analyzing sensitivity data10.1080/01621459.1948.10483254 ↗
57. ISO 12106-2017 Metallic materials – fatigue testing - axial-strain-controlled method.
58. ASTM E647-2013 Standard test method for measurement of fatigue crack growth rates.
59. The evolution of microstructure during annealing of Al-Mg-Sc-Zr alloy deformed by equal channel angular pressing10.12693/APhysPolA.134.895 ↗
60. Continuous recrystallisation of lamellar deformation structures produced by severe deformation10.1016/j.actamat.2004.03.019 ↗
61. Quantification of annealed microstructures in ARB processed aluminum10.1016/j.actamat.2006.02.046 ↗
62. Recrystallization mechanisms in 5251 H14 and 5251 O aluminum friction stir welds10.1016/j.msea.2006.09.036 ↗
63. Microstructural evolution in recrystallized and unrecrystallized Al–Mg–Sc alloys during superplastic deformation10.1016/j.msea.2012.03.076 ↗
64. Effect of intermediate annealing on texture evolution and plastic anisotropy in an Al-Mg autobody alloy10.1007/s11661-000-0057-7 ↗
65. Texture decomposition with particle swarm optimization method10.1016/j.commatsci.2005.09.015 ↗
66. The grain boundary geometry for optimum resistance to growth of short fatigue cracks in high strength Al-alloys10.1016/j.ijfatigue.2005.06.021 ↗
67. Mechanisms for Goss-grains induced crack deflection and enhanced fatigue crack propagation resistance in fatigue stage II of an AA2524 alloy10.1016/j.msea.2014.12.021 ↗
68. Suresh · 1998
69. Schijve J. Fatigue of structures and materials; 2009.10.1007/978-1-4020-6808-9 ↗
70. Shu DL. Mechanical properties of engineering materials. Beijing:China machine press; 2003.
71. Fatigue crack growth behavior of a coarse- and a fine-grained high manganese austenitic twin-induced plasticity steel10.1016/j.msea.2014.03.035 ↗
72. Role of twinning and slip in cyclic deformation of extruded Mg–3%Al–1%Zn alloys10.1016/j.scriptamat.2010.08.008 ↗
73. Effect of grain size on the fatigue crack growth behavior of 2524–T3 aluminum alloy10.1016/j.acme.2016.01.004 ↗
74. The role of twinning–detwinning on fatigue fracture morphology of Mg–3%Al–1%Zn alloy10.1016/j.msea.2008.04.056 ↗
75. A grain boundary interaction model for microstructurally short fatigue cracks10.1016/j.ijfatigue.2018.04.029 ↗
76. Fatigue crack propagation in ultrafine grained Al–Mg alloy10.1016/j.ijfatigue.2005.06.027 ↗
77. Deformation behavior of a modified 5083 aluminum alloy10.1016/j.msea.2004.10.002 ↗
78. Hall-Petch relationship in friction stir welds of equal channel angular-pressed aluminium alloys10.1016/S0921-5093(03)00008-X ↗
79. Microstructure characterization in cryomilled Al 508310.1016/j.msea.2006.05.039 ↗