Room and elevated temperature fatigue crack propagation behavior of Inconel 718 alloy fabricated by laser powder bed fusion
Source abstract
Abstract
Abstract The fatigue crack propagation (FCP) behavior of Inconel 718 alloy manufactured by laser powder bed fusion (L-PBF) was studied at 25 and 650 °C, and compared to those of conventionally processed counterpart. The FCP rates of L-PBF Inconel 718 alloy were found to be significantly higher than those of conventionally processed counterpart at 25 °C in low and intermediate ΔK regimes. The FCP rates decreased in near-threshold ΔK regime at 650 °C, while the reversal occurred above ΔK of 7 MPa√m, as compared to those at 25 °C. The FCP behavior of L-PBF Inconel 718 alloy was discussed based on micrographic and fractographic analyses.
Source: openaire · Quality: candidate unverified · Source record ↗
Research context
OpenAlex topics: Additive Manufacturing Materials and Processes · Additive Manufacturing and 3D Printing Technologies · High Entropy Alloys Studies
SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.
References (48)
Show source-provided references
1. Additive manufacturing: making imagination the major limitation10.1007/s11837-014-0886-2 ↗
2. Investigation of the anisotropic fatigue behavior of additively manufactured structures made of AISI 316L with short-time procedures PhyBaLLIT and PhyBaLCHT10.1016/j.ijfatigue.2019.03.022 ↗
3. Low cycle fatigue behavior of direct metal laser sintered Inconel alloy 71810.1016/j.ijfatigue.2016.08.019 ↗
4. Additive manufacturing of alloy 718 via electron beam melting: Effect of post-treatment on the microstructure and the mechanical properties10.3390/ma12010068 ↗
5. Finite element analysis of melt pool thermal characteristics with passing laser in SLM process10.1016/j.ijleo.2019.163068 ↗
6. In-process sensing in selective laser melting (SLM) additive manufacturing10.1186/s40192-016-0045-4 ↗
7. Rapid manufacturing of metal components by laser forming10.1016/j.ijmachtools.2005.09.005 ↗
8. A review of mechanical properties of additively manufactured inconel 718
9. A study of the microstructural evolution during selective laser melting of Ti–6Al–4V10.1016/j.actamat.2010.02.004 ↗
10. The effect of δ phase on the mechanical properties of an Inconel 718 superalloy10.1007/s11665-012-0433-7 ↗
11. Long fatigue crack growth in Inconel 718 produced by selective laser melting10.1016/j.ijfatigue.2016.03.012 ↗
12. Studies of standard heat treatment effects on microstructure and mechanical properties of laser net shape manufactured Inconel 71810.1007/s11661-009-9949-3 ↗
13. Effect of energy input on microstructural evolution of direct laser fabricated IN718 alloy10.1016/j.matchar.2015.06.027 ↗
14. Experimental investigation of Inconel 718 during die-sinking electric discharge machining
15. Effect of standard heat treatment on the microstructure and mechanical properties of hot isostatically pressed superalloy Inconel 71810.1016/S0921-5093(03)00079-0 ↗
16. The microstructure evolution and tensile properties of Inconel 718 fabricated by high-deposition-rate laser directed energy deposition
17. Microstructures and mechanical behavior of Inconel 718 fabricated by selective laser melting10.1016/j.actamat.2011.12.032 ↗
18. Review on powder-bed laser additive manufacturing of Inconel 718 parts10.1177/0954405415619883 ↗
19. Microstructure and mechanical properties of selective laser melted Inconel 718 compared to forging and casting10.1016/j.matlet.2015.10.136 ↗
20. A damage evolution model based on micro-structural characteristics for an additive manufactured superalloy under monotonic and cyclic loading conditons10.1016/j.ijfatigue.2019.105279 ↗
21. Microstructure, fatigue, and impact toughness properties of additively manufactured nickel alloy 718
22. Additive manufacturing of fatigue resistant materials challenges and opportunities10.1016/j.ijfatigue.2017.01.001 ↗
23. Enhancing fatigue strength of selective laser melting-fabricated Inconel 718 by tailoring heat treatment route
24. Fatigue properties of a titanium alloy (Ti–6Al–4V) fabricated via electron beam melting (EBM): Effects of internal defects and residual stress10.1016/j.ijfatigue.2016.04.022 ↗
25. The influence of Laves phases on the high-cycle fatigue behavior of laser additive manufactured Inconel 71810.1016/j.msea.2017.03.098 ↗
26. Influence of defects and as-built surface roughness on fatigue properties of additively manufactured alloy 71810.1016/j.msea.2018.08.072 ↗
27. Fatigue crack growth behavior of Inconel 718 produced by selective laser melting
28. ASTM Standard E647. Standard test method for measurement of fatigue crack growth rates. Annual Book of ASTM Standards 2002; 03.01.
29. The effect of Laves phase on the mechanical properties of wrought and cast+ HIP Inconel 718
30. Investigation of dissolution behavior of Laves phase in Inconel 718 fabricated by laser directed energy deposition
31. Microstructure characteristics and mechanical behaviour of a selective laser melted Inconel 718 alloy
32. Micromechanisms of fatigue crack growth in a single crystal Inconel 718 nickel-based superalloy10.1016/S1359-6454(99)00123-8 ↗
33. Microstructure and fatigue crack growth in a γ-Fe-Ni-Al alloy10.1016/0001-6160(76)90104-8 ↗
34. Effect of pre-ptraining on high cycle fatigue and fatigue crack propagation behaviors of precipitation hardened steel
35. Near-threshold fatigue crack propagation behavior of austenitic high-Mn steels10.1016/j.matchar.2016.09.035 ↗
36. Reviews on factors affecting fatigue behavior of high-Mn steels10.1007/s12540-017-7459-1 ↗
37. Effect of superplastic forming exposure on fatigue crack propagation behavior of Ti-6Al-4V alloy10.1007/s12540-016-6075-9 ↗
38. Crack growth behavior in alloy 718 at 425°C10.1115/1.3443507 ↗
39. Assessment of mechanical properties and fatigue performance of a selective laser melted nickel-base superalloy Inconel 71810.1016/j.msea.2019.05.007 ↗
40. Gamma double prime precipitation kinetic in alloy 71810.1016/j.msea.2007.08.046 ↗
41. Knowledge of process-structure-property relationships to engineer better heat treatments for laser powder bed fusion additive manufactured Inconel 718
42. Effect of boron on fatigue crack growth behavior in superalloy IN 718 at RT and 650 °C10.1016/j.msea.2005.08.206 ↗
43. Fatigue and fracture behavior of nickel-based superalloy Inconel 718 up to the very high cycle regime10.1631/jzus.A1000171 ↗
44. Micromechanisms of fatigue crack growth in a forged Inconel 718 nickel-based superalloy10.1016/S0921-5093(99)00214-2 ↗
45. Crack growth in IN718 at high temperature10.1016/S0142-1123(01)00031-7 ↗
46. Fatigue crack propagation in Ti-6242 as a function of temperature and waveform10.1016/0013-7944(90)90074-Q ↗
47. Fatigue crack growth behaviour of Inconel 718 with high temperature hold times10.1016/j.proeng.2010.03.118 ↗
48. Effect of service exposure on fatigue crack propagation of Inconel 718 turbine disc material at elevated temperatures10.1016/j.matchar.2014.06.022 ↗