Effect of microstructure on high cycle fatigue behavior of Ti–5Al–5Mo–5V–3Cr–1Zr titanium alloy
Source abstract
Abstract
Abstract High-cycle fatigue (HCF) behavior of Ti–5Al–5Mo–5V–3Cr–1Zr (Ti-55531) alloy with both lamellar microstructure (LM) and bimodal microstructure (BM) was studied at room temperature. The results indicate that BM presents much higher strength, lower ductility and slightly higher HCF strength (107 cycles, R = −1) than those of LM. Typical dislocation structures including straight prismatic slip lines, curved dislocation lines, dislocation tangles and twins can be discovered in fatigued specimens with two different microstructures. Primary α (αp) particles and secondary α (αs) lamellae accommodate more cyclic deformation than retained β (βr) laths. Grain boundary (GB) α layers have more effect on promoting crack initiation in LM than that in BM. As a result, fatigue microcracks mainly initiate at the interface between GB α films and prior β grains or at the αs/βr interphase for LM. However, microcracks primarily nucleate at the αp/βtrans (β transformed microstructure) interface or at αp particles in BM. The combination of transgranular and intergranular crack propagation could be observed in the two microstructures. Crack front profile of macrocrack in LM is rougher than that of BM during the stable propagation region.
Source: openaire · Quality: candidate unverified · Source record ↗
Research context
OpenAlex topics: Titanium Alloys Microstructure and Properties · Intermetallics and Advanced Alloy Properties · Nuclear Materials and Properties
SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.
References (36)
Show source-provided references
1. High-cycle fatigue resistance in beta-titanium alloys10.1007/s11837-000-0097-x ↗
2. The use of β titanium alloys in the aerospace industry10.1007/s11665-013-0728-3 ↗
3. A.I.H. Committee · 1996
4. Cyclic deformation response of β-Annealed Ti-5Al-5V-5Mo-3Cr alloy under compressive loading conditions10.1007/s11661-011-0705-0 ↗
5. Advanced materials and technology for A380 structure
6. Effect of α-phase morphology on low-cycle fatigue behavior of TC21 alloy10.1016/j.ijfatigue.2015.01.010 ↗
7. The crack initiation behavior and the fatigue limit of Ti–5Al–5Mo–5V–1Cr–1Fe titanium alloy with basket-weave microstructure10.1016/j.jallcom.2015.01.077 ↗
8. Microstructure and high cycle fatigue fracture surface of a Ti–5Al–5Mo–5V–1Cr–1Fe titanium alloy10.1016/j.msea.2013.03.047 ↗
9. Lütjering · 2007
10. Formation of grain boundary α in β Ti alloys: its role in deformation and fracture behavior of these alloys10.1007/s11661-010-0322-3 ↗
11. The influence of soft, precipitate-free zones at grain boundaries in Ti and Al alloys on their fatigue and fracture behavior10.1016/j.msea.2006.07.168 ↗
12. Study of the hot deformation behaviour in Ti–5Al–5Mo–5V–3Cr–1Zr10.1016/j.msea.2011.07.068 ↗
13. Quantitative microstructural characterization of a near beta Ti alloy, Ti-5553 under different processing conditions10.1016/j.matchar.2013.03.016 ↗
14. β Phase decomposition in Ti–5Al–5Mo–5V–3Cr10.1016/j.actamat.2009.04.031 ↗
15. Ω-Assisted nucleation and growth of α precipitates in the Ti–5Al–5Mo–5V–3Cr–0.5Fe β titanium alloy10.1016/j.actamat.2009.01.007 ↗
16. Zheng · 2013
17. On variant distribution and coarsening behavior of the α phase in a metastable β titanium alloy10.1016/j.actamat.2016.01.023 ↗
18. Role of ω phase in the formation of extremely refined intragranular α precipitates in metastable β-titanium alloys10.1016/j.actamat.2015.11.020 ↗
19. Processing-microstructure-yield strength correlation in a near β Ti alloy, Ti–5Al–5Mo–5V–3Cr10.1016/j.msea.2014.04.113 ↗
20. Panza-Giosa · 2010
21. Microstructure-fracture toughness correlation in an aircraft structural component alloy Ti–5Al–5V–5Mo–3Cr10.1016/j.msea.2013.01.017 ↗
22. Static and fatigue characterization of the Ti5553 titanium alloy10.1111/ffe.12011 ↗
23. Probabilistic measurements of the fatigue limit data from a small sampling up-and-down test method10.1016/j.ijfatigue.2008.06.004 ↗
24. Huang C, Zhao Y, Xin S, Tan C, Zhou W, Li Q, et al. High cycle fatigue behavior of Ti–5Al–5Mo–5V–3Cr–1Zr titanium alloy with lamellar microstructure, Mater Sci Eng A, 2016 [in preparation].10.1016/j.msea.2016.11.014 ↗
25. The influence of grain size on the high cycle fatigue crack initiation of a metastable beta Ti alloy10.1007/BF02661593 ↗
26. Liu · 2005
27. On the correlation between fatigue striation spacing and crack growth rate: a Three-Dimensional (3-D) x-ray synchrotron tomography study10.1007/s11661-011-0963-x ↗
28. A detailed study of the relationship between fatigue crack growth rate and striation spacing in a range of low alloy ferritic steels10.1016/j.engfailanal.2009.04.028 ↗
29. Crystallography of fatigue crack initiation and growth in fully lamellar Ti-6Al-4V10.1007/s11661-009-0064-2 ↗
30. Crystallography of fluted fracture in near-α titanium alloys10.1007/s11661-009-0091-z ↗
31. Deformation of an alloy with a lamellar microstructure: experimental behavior of individual widmanstatten colonies of an α-β titanium alloy10.1007/BF02643801 ↗
32. Cyclic deformation response and micromechanisms of Ti alloy Ti–5Al–5V–5Mo–3Cr–0.5Fe10.1016/j.msea.2011.08.045 ↗
33. Deformation behavior of HCP Ti-Al alloy single crystals10.1007/s11661-002-0153-y ↗
34. 3-D observations of short fatigue crack interaction with lamellar and duplex microstructures in a two-phase titanium alloy10.1016/j.actamat.2010.11.015 ↗
35. Study on the relationship between microstructure and mechanical property in a metastable β titanium alloy10.1016/j.jallcom.2014.12.100 ↗
36. Fatigue cracking at twin boundaries: effects of crystallographic orientation and stacking fault energy10.1016/j.actamat.2012.02.016 ↗