The effect of ultrasonic surface rolling process on the fretting fatigue property of GH4169 superalloy
Source abstract
Abstract
Abstract To improve the fretting fatigue (FF) resistance of GH4169 superalloy, ultrasonic surface rolling process (USRP) is carried once and three times on material surface and the effect of surface integrity on FF is investigated. The results show that USRP significantly reduces the surface roughness of GH4169 superalloy and improves surface micro-hardness as well as induces a high intensity compressive residual stress at deep thickness. The dislocation density beneath the top surface is increased and the grains of the material surface are refined. A gradient nanostructured layer is observed beneath the surface and the equiaxed nanograins are generated with the size of around 37.6 nm at the top surface of USRP-3 sample. The FF test indicates the FF life of GH4169 superalloy increase by 3.6 times and 11 times, by one and three USRP treatments, respectively. In addition, the factor separation test indicates that the compressive residual stress plays an important role in improving the FF life of GH4169 superalloy.
Source: openaire · Quality: candidate unverified · Source record ↗
Research context
OpenAlex topics: Surface Treatment and Residual Stress · Metal Alloys Wear and Properties · Metal and Thin Film Mechanics
SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.
References (75)
Show source-provided references
1. Dynamic recrystallization behavior of a typical nickel-based superalloy during hot deformation10.1016/j.matdes.2013.12.072 ↗
2. Hot deformation behavior of GH4169 superalloy associated with stick δ phase dissolution during isothermal compression process10.1016/j.msea.2012.01.121 ↗
3. Stress rupture fracture model and microstructure evolution for waspaloy10.1007/s11661-013-1660-8 ↗
4. Evaluation of the influence of grain structure on the fatigue variability of waspaloy
5. Measurement, analysis and prediction of fretting wear damage in a representative aeroengine spline coupling10.1016/j.wear.2004.08.003 ↗
6. Kumari S, P V S, A B, H N NM. Parametric study to mitigate fretting fatigue in dovetail joint of aeroengine compressor. J Meas Eng 2017;5:19–28. doi:10.21595/jme.2017.18270.10.21595/jme.2017.18270 ↗
7. Fatigue fracture of crankshaft of an aircraft engine10.1016/S1350-6307(01)00022-X ↗
8. Determination of fretting fatigue behavior in titanium alloy Ti-6Al-4V: a review
9. An investigation on fretting fatigue mechanism under complex cyclic loading conditions10.1016/j.ijfatigue.2016.03.030 ↗
10. Fretting fatigue crack nucleation: a review10.1016/j.triboint.2018.01.029 ↗
11. Fretting wear and fretting fatigue behaviors of diamond-like carbon and graphite-like carbon films deposited on Ti-6Al-4V alloy10.1016/j.apsusc.2014.06.006 ↗
12. Plain and fretting fatigue behavior of Ti6Al4V alloy coated with TiAlN thin film10.1016/j.triboint.2013.06.006 ↗
13. Statistical optimization and fretting fatigue study of Zr/ZrO2 nanotubular array coating on Ti-6Al-4V10.1016/j.surfcoat.2014.07.046 ↗
14. Investigation on the fretting fatigue behaviors of Ti-6Al-4V dovetail joint specimens treated with shot-peening10.1016/j.wear.2016.12.004 ↗
15. Effects of fatigue and fretting on residual stresses introduced by laser shock peening10.1016/j.msea.2006.07.020 ↗
16. Fretting fatigue characteristics of Ti-6Al-4V alloy with a gradient nanostructured surface layer induced by ultrasonic surface rolling process10.1016/j.ijfatigue.2019.03.042 ↗
17. Influence of surface coating on Ti811 alloy resistance to fretting fatigue at elevated temperature10.1007/s12598-009-0053-z ↗
18. Effect of shot peening on fretting fatigue of Ti811 alloy at elevated temperature10.1016/j.ijfatigue.2008.10.004 ↗
19. Fretting fatigue tests on shrink-fit specimens and investigations into the strength enhancement induced by deep rolling10.1016/j.ijfatigue.2015.08.007 ↗
20. Improvement of the fretting fatigue and fretting wear of Ti6Al4V by duplex surface modification10.1016/S0257-8972(99)00279-0 ↗
21. Behaviour of shot peening combined with WC-Co HVOF coating under complex fretting wear and fretting fatigue loading conditions10.1016/j.surfcoat.2006.08.094 ↗
22. Investigation of shot peening combined with plasma-sprayed CuNiIn coating on the fretting fatigue behavior of Ti-6Al-4V dovetail joint specimens10.1016/j.surfcoat.2018.12.006 ↗
23. Investigation into effects of re-shot-peening on fretting fatigue behavior of Ti-6Al-4V10.1016/j.msea.2004.08.040 ↗
24. Nanostructure and surface roughness in the processed surface layer of Ti-6Al-4V via shot peening10.1016/j.matchar.2016.11.020 ↗
25. The effects of laser peening and shot peening on fretting fatigue in Ti-6Al-4V coupons10.1016/j.triboint.2009.04.005 ↗
26. Effects of fretting fatigue on the residual stress of shot peened Ti-6Al-4V samples10.1016/j.msea.2005.02.028 ↗
27. Effect of TiN/Ti composite coating and shot peening on fretting fatigue behavior of TC17 alloy at 350 °C10.1016/j.surfcoat.2009.02.058 ↗
28. Low Cycle Fatigue behavior of AA7075 with surface gradient structure produced by Ultrasonic Shot Peening10.1016/j.prostr.2016.06.410 ↗
29. Enhanced tribological performance of a gradient nanostructured interstitial-free steel10.1016/j.wear.2018.02.010 ↗
30. Gradient crystalline structure induced by ultrasonic impacting and rolling and its effect on fatigue behavior of TC11 titanium alloy10.1016/j.rinp.2017.05.026 ↗
31. Research on friction and wear behavior of gradient nano-structured 40Cr steel induced by high frequency impacting and rolling10.1016/j.engfailanal.2017.09.012 ↗
32. Enhanced mechanical behaviors of gradient nano-grained austenite stainless steel by means of ultrasonic impact treatment10.1016/j.rinp.2017.04.002 ↗
33. Fatigue life improvement through surface nanostructuring of stainless steel by means of surface mechanical attrition treatment10.1016/j.scriptamat.2006.01.049 ↗
34. Analysis of fatigue resistance improvements via surface severe plastic deformation10.1016/j.ijfatigue.2007.10.010 ↗
35. Enhanced fatigue resistance of Cu with a gradient nanograined surface layer10.1016/j.scriptamat.2013.01.031 ↗
36. Fatigue behaviors of AISI 316L stainless steel with a gradient nanostructured surface layer10.1016/j.actamat.2014.12.057 ↗
37. Simultaneous enhancement of stress- and strain-controlled fatigue properties in 316L stainless steel with gradient nanostructure10.1016/j.actamat.2019.02.008 ↗
38. Deformation compatibility between nanotwinned and recrystallized grains enhances resistance to interface cracking in cyclic loaded stainless steel10.1016/j.actamat.2018.11.033 ↗
39. Effect of surface mechanical attrition treatment on low cycle fatigue properties of an austenitic stainless steel10.1016/j.ijfatigue.2017.06.011 ↗
40. Fatigue resistance of welded details enhanced by ultrasonic impact treatment (UIT)10.1016/S0142-1123(03)00151-8 ↗
41. Influence of microstructural features and deformation-induced martensite on hardening of stainless steel by cryogenic ultrasonic impact treatment10.1016/j.surfcoat.2017.11.019 ↗
42. Effects of ultrasonic impact treatment on pre-fatigue loaded high-strength steel welded joints10.1016/j.ijfatigue.2015.06.017 ↗
43. Improvement of high-temperature fatigue performance in the nickel-based alloy by LSP-induced surface nanocrystallization10.1016/j.jallcom.2018.01.070 ↗
44. Effect of laser shock peening on elevated temperature residual stress, microstructure and fatigue behavior of ATI 718Plus alloy10.1016/j.ijfatigue.2017.08.006 ↗
45. Bimodal nanocrystallization of NiTi shape memory alloy by laser shock peening and post-deformation annealing10.1016/j.actamat.2011.07.070 ↗
46. Microstructure and mechanical properties of copper subjected to cryogenic laser shock peening10.1063/1.3651508 ↗
47. Ye C, Cheng GJ. Fatigue performance improvement by dynamic strain aging and dynamic precipitation in warm laser shock peening of AISI 4140 steel. In: ASME 2010 Int Manuf Sci Eng Conf MSEC 2010 2010;2:317–25. doi:10.1115/MSEC2010-34301.10.1115/MSEC2010-34301 ↗
48. Effect of Ultrasonic Nanocrystal Surface Modification on residual stress, microstructure and fatigue behavior of ATI 718Plus alloy10.1016/j.msea.2017.11.043 ↗
49. Effect of ultrasonic nanocrystal surface modification on elevated temperature residual stress, microstructure, and fatigue behavior of ATI 718Plus alloy10.1016/j.ijfatigue.2018.01.017 ↗
50. Surface amorphization of NiTi alloy induced by Ultrasonic Nanocrystal Surface Modification for improved mechanical properties10.1016/j.jmbbm.2015.09.005 ↗
51. Increasing fracture strength in bulk metallic glasses using ultrasonic nanocrystal surface modification10.1016/j.jallcom.2017.05.056 ↗
52. Gradient nanostructure and residual stresses induced by Ultrasonic Nano-crystal Surface Modification in 304 austenitic stainless steel for high strength and high ductility10.1016/j.msea.2014.06.114 ↗
53. Effects of ultrasonic nanocrystal surface modification (UNSM) on residual stress state and fatigue strength of AISI 30410.1007/s11665-009-9445-3 ↗
54. Residual stresses after deep rolling of a torsion bar made from high strength steel10.1016/j.jmatprotec.2014.11.042 ↗
55. On the effect of deep-rolling and laser-peening on the stress-controlled low- and high-cycle fatigue behavior of Ti-6Al-4V at elevated temperatures up to 550 °c10.1016/j.ijfatigue.2012.03.008 ↗
56. The effects of deep rolling and shot peening on fretting fatigue resistance of Aluminum-7075-T610.1016/j.msea.2009.03.020 ↗
57. The influence of deep rolling on the surface integrity of AISI 1060 high carbon steel10.1016/j.procir.2014.04.006 ↗
58. The influence of low-plasticity burnishing process on the fatigue life of friction-stir-processed Al 7075–T6 samples10.1111/ffe.12950 ↗
59. Effect of shot-peening and low-plasticity burnishing on the high-cycle fatigue strength of DIN 34CrNiMo6 alloy steel10.1016/j.ijfatigue.2018.10.014 ↗
60. An engineering high cycle fatigue strength prediction model for low plasticity burnished samples10.1016/j.ijfatigue.2017.06.013 ↗
61. Effect of the ultrasonic surface rolling process on the fretting fatigue behavior of Ti-6Al-4V alloy10.3390/ma10070833 ↗
62. Determination of the plastic properties of materials treated by ultrasonic surface rolling process through instrumented indentation10.1016/j.msea.2014.01.096 ↗
63. Surface nanocrystallization and its effect on fatigue performance of high-strength materials treated by ultrasonic rolling process10.1007/s00170-015-7485-4 ↗
64. Investigations on the nanocrystallization of 40Cr using ultrasonic surface rolling processing10.1016/j.apsusc.2008.06.034 ↗
65. The effects of ultrasonic nanocrystal surface modification on the fatigue performance of 3D-printed Ti6410.1016/j.ijfatigue.2017.05.019 ↗
66. Enhanced surface properties of austenitic stainless steel by electropulsing-assisted ultrasonic surface rolling process10.1016/j.surfcoat.2015.10.026 ↗
67. Development of ultrasonic thread root rolling technology for prolonging the fatigue performance of high strength thread10.1016/j.jmatprotec.2014.05.019 ↗
68. A direct comparison in the fatigue resistance enhanced by surface severe plastic deformation and shot peening in a C-2000 superalloy10.1016/j.msea.2009.10.028 ↗
69. Fracture behavior of an austenitic stainless steel with nanoscale deformation twins10.1016/j.scriptamat.2016.09.012 ↗
70. Effect of surface nanostructure on tensile behavior of superalloy IN71810.1016/j.matdes.2014.04.084 ↗
71. Hall-petch relation and boundary strengthening10.1016/j.scriptamat.2004.06.002 ↗
72. Strain-controlled cyclic stability and properties of Cu with highly oriented nanoscale twins10.1016/j.actamat.2014.08.011 ↗
73. Improved fatigue resistance of gradient nanograined Cu10.1016/j.actamat.2018.12.018 ↗
74. Effect of shot-peening on the fretting wear and crack initiation behavior of Ti-6Al-4V dovetail joint specimens10.1016/j.ijfatigue.2017.10.020 ↗
75. Effect of shot peening on the freeting wear of Ti-6Al-4V10.1016/S0043-1648(01)00671-8 ↗