Improving the fretting and corrosion fatigue performance of 300M ultra-high strength steel using the ultrasonic surface rolling process
Source abstract
Abstract
Abstract 300M ultra-high strength steels (300M steels) are frequently used in the manufacture of aircraft landing gear due to their high strength and ductility. However, their high sensitivity to surface defects accelerates fatigue failure and hinders their wider application. In this work, ultrasonic surface rolling processing (USRP) was used to process 300M steel. The surface roughness, hardness, microstructure, and residual stresses before and after USRP treatment were compared. The surface roughness for USRP-treated samples (0.062 μm) was found to be lower than that for untreated samples (0.32 μm). In addition, a plastically deformed layer was generated on the surface of USRP-treated samples that resulted in higher hardness. Beneficial compressive residual stresses were introduced as a result of USRP treatment. The better surface finish, higher surface hardness and compressive residual stresses lead to significant improvement in the resistance of the 300M steels to fretting fatigue and corrosion fatigue. The fretting fatigue life increased from 11.9 K cycles to 56.3 K cycles, while the corrosion fatigue life increased from 29.9 K cycles to 702.1 K cycles.
Source: openaire · Quality: candidate unverified · Source record ↗
Research context
OpenAlex topics: Surface Treatment and Residual Stress · Metal Alloys Wear and Properties · Metal and Thin Film Mechanics
SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.
References (50)
Show source-provided references
1. Fretting fatigue behavior of high-strength steel monostrands under bending load10.1016/j.ijfatigue.2014.08.009 ↗
2. Very high cycle fatigue of a high strength steel under sea water corrosion: a strong corrosion and mechanical damage coupling10.1016/j.ijfatigue.2015.01.004 ↗
3. Fracture mechanics applied to engineering problems-strain energy density fracture criterion10.1016/0013-7944(74)90033-2 ↗
4. Effect of surface mechanical attrition treatment on low cycle fatigue properties of an austenitic stainless steel10.1016/j.ijfatigue.2017.06.011 ↗
5. Studies on fatigue life enhancement of pre-fatigued spring steel specimens using laser shock peening10.1016/j.matdes.2013.08.104 ↗
6. Effect of laser shock peening on residual stress, microstructure and fatigue behavior of ATI 718Plus alloy10.1016/j.ijfatigue.2017.04.016 ↗
7. The effects of deep rolling and shot peening on fretting fatigue resistance of Aluminum-7075-T610.1016/j.msea.2009.03.020 ↗
8. Fatigue performance improvement in AISI 4140 steel by dynamic strain aging and dynamic precipitation during warm laser shock peening10.1016/j.actamat.2010.10.032 ↗
9. Mitigation of SCC and corrosion fatigue failures in 300M landing gear steel using mechanical suppression
10. Fretting fatigue tests on shrink-fit specimens and investigations into the strength enhancement induced by deep rolling10.1016/j.ijfatigue.2015.08.007 ↗
11. Effect of shot blasting on plain fatigue and fretting fatigue behaviour of Al-Mg-Si alloy AA606110.1016/j.ijfatigue.2004.07.007 ↗
12. Effect of shot peening on the fatigue resistance of laser surface melted 20CrMnTi steel gear10.1016/j.msea.2015.01.074 ↗
13. The influence of shot peening on the fatigue response of Ti-6Al-4V surfaces subject to different machining processes10.1016/j.ijfatigue.2018.02.022 ↗
14. Effects of shot-peening on fretting-fatigue behavior of Ti-6Al-4V10.1115/1.1448323 ↗
15. On the effect of shot-peening on fretting fatigue of Al7075-T6 under cyclic normal contact loading10.1016/j.surfcoat.2017.08.067 ↗
16. Enhancement of fatigue strength of SAE 9245 steel by shot peening10.1016/S0167-577X(02)00838-8 ↗
17. Effect of shot peening on fretting fatigue of Ti811 alloy at elevated temperature10.1016/j.ijfatigue.2008.10.004 ↗
18. Effect of ultrasonic surface rolling at low temperatures on surface layer microstructure and properties of HIP Ti-6Al-4V alloy10.1016/j.surfcoat.2017.01.099 ↗
19. Surface nanocrystallization of 17–4 precipitation-hardening stainless steel subjected to ultrasonic surface rolling process10.1016/j.msea.2018.04.033 ↗
20. Microstructure and surface properties of 17–4PH stainless steel by ultrasonic surface rolling technology10.1016/j.surfcoat.2017.04.052 ↗
21. Determination of the plastic properties of materials treated by ultrasonic surface rolling process through instrumented indentation10.1016/j.msea.2014.01.096 ↗
22. Effects of the different frequencies and loads of ultrasonic surface rolling on surface mechanical properties and fretting wear resistance of HIP Ti–6Al–4V alloy10.1016/j.apsusc.2016.07.120 ↗
23. Influence of the ultrasonic surface rolling process on stress corrosion cracking susceptibility of high strength pipeline steel in neutral pH environment10.1039/C7RA05425D ↗
24. Study on surface characteristics of 7050–T7451 aluminum alloy by ultrasonic surface rolling process10.1007/s00170-016-8659-4 ↗
25. Influence of ultrasonic surface rolling on microstructure and wear behavior of selective laser melted Ti-6Al-4V alloy10.3390/ma10101203 ↗
26. Effect of the ultrasonic surface rolling process on the fretting fatigue behavior of Ti-6Al-4V alloy10.3390/ma10070833 ↗
27. Investigations on the nanocrystallization of 40Cr using ultrasonic surface rolling processing10.1016/j.apsusc.2008.06.034 ↗
28. On the determination of residual stress and strain fields by sharp indentation testing. PartI: theoretical and numerical analysis10.1016/S1359-6454(01)00122-7 ↗
29. Improvement of the fatigue strength of SUS304 austenite stainless steel using ultrasonic nanocrystal surface modification10.1016/j.surfcoat.2012.12.033 ↗
30. Effects of ultrasonic nanocrystal surface modification on the wear and micropitting behavior of bearing steel in boundary lubricated steel-steel contacts10.1016/j.wear.2017.09.012 ↗
31. The effects of ultrasonic nanocrystal surface modification on the fatigue performance of 3D-printed Ti6410.1016/j.ijfatigue.2017.05.019 ↗
32. Finite element modeling of ultrasonic surface rolling process10.1016/j.jmatprotec.2011.07.009 ↗
33. Fracture mechanics approach to fretting fatigue and problems to be solved10.1016/S0301-679X(02)00136-6 ↗
34. Initiation and propagation of fretting fatigue cracks10.1016/0043-1648(76)90079-X ↗
35. General relationship between strength and hardness10.1016/j.msea.2011.08.061 ↗
36. Investigation on the fretting fatigue behaviors of Ti-6Al-4V dovetail joint specimens treated with shot-peening10.1016/j.wear.2016.12.004 ↗
37. The basic relationships between residual stress, white layer, and fatigue life of hard turned and ground surfaces in rolling contact10.1016/j.cirpj.2009.12.002 ↗
38. Finite element method and experimental investigation on the residual stress fields and fatigue performance of cold expansion hole10.1016/j.matdes.2009.09.031 ↗
39. Fretting wear and friction reduction of CP titanium and Ti-6Al-4V alloy by ultrasonic nanocrystalline surface modification10.1016/j.surfcoat.2012.06.046 ↗
40. Fretting wear behavior of laser peened Ti-6Al-4V10.1080/10402004.2012.686087 ↗
41. Prediction of cracking in Ti-6Al-4V alloy under fretting-wear: use of the SWT criterion10.1016/j.wear.2004.11.026 ↗
42. Residual stress and surface roughness in fretting fatigue10.1088/0022-3727/25/1A/036 ↗
43. Improvement of the fretting fatigue and fretting wear of Ti6Al4V by duplex surface modification10.1016/S0257-8972(99)00279-0 ↗
44. Influence of residual stresses from shot peening on fretting fatigue crack growth10.1111/j.1460-2695.2007.01165.x ↗
45. Fretting fatigue behaviour of shot-peened Ti-6Al-4V at room and elevated temperatures10.1046/j.1460-2695.2003.00677.x ↗
46. Fretting behavior of shot peened Ti-6Al-4V under slip controlled mode10.1016/j.wear.2005.03.022 ↗
47. Analysis of fretting fatigue of cavitation shotless peened Ti-6Al-4V10.1007/s11249-010-9581-9 ↗
48. Improvement in fretting wear and fatigue resistance of Ti-6Al-4V by application of several surface treatments and coatings10.1016/S0257-8972(98)00528-3 ↗
49. Mechanics of fretting fatigue crack formation10.1016/0043-1648(96)06937-2 ↗
50. The aspect ratio of surface grooves and metastable pitting of stainless steel10.1016/S0010-938X(01)00039-7 ↗