Cyclic deformation and fatigue behavior of additively manufactured 17–4 PH stainless steel
Source abstract
Abstract
Abstract Static and fatigue experiments were conducted on conventionally manufactured (CM) and additively manufactured (AM) 17–4 PH stainless steels in ambient air. The fatigue experiments were tested under the fully reversed strain-controlled condition with the strain amplitudes ranging from 0.15% to 1.0%. The two manufacturing conditions result in similar tensile strengths but the AM 17–4 PH stainless steel has a significantly lower ductility than that of the CM steel. The fatigue limit of the CM 17–4 PH stainless steel is approximately 640 MPa and the fatigue limit of the AM steel is approximately 300 MPa. The strain-life fatigue curves of both materials display a kink point from low cycle fatigue regime to high cycle fatigue regime. Defects and porosity from the additive manufacturing process contribute to the weakened fatigue properties and ductility of the AM stainless steel.
Source: openaire · Quality: candidate unverified · Source record ↗
Research context
OpenAlex topics: Additive Manufacturing Materials and Processes · Welding Techniques and Residual Stresses · Additive Manufacturing and 3D Printing Technologies
SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.
References (50)
Show source-provided references
1. Beaman JJ, Deckard CR. Selective laser sintering with assisted powder handling. U.S. Patent No. 4,938,816, 1990.
2. Laser additive manufacturing of metallic components: materials, processes and mechanisms10.1179/1743280411Y.0000000014 ↗
3. Optimized postweld heat treatment procedures for 17–4 PH stainless steels
4. Aging reactions in a 17–4 PH stainless steel10.1016/S0254-0584(01)00460-6 ↗
5. Microstructure and mechanical behavior of 17–4 precipitation hardenable steel processed by selective laser melting10.1007/s11665-014-1226-y ↗
6. The strength, fracture toughness, and low cycle fatigue behavior of 17–4 PH stainless steel10.1007/BF02646331 ↗
7. Effects of aging on the microstructure of 17–4 PH stainless steel10.1016/0025-5416(88)90420-X ↗
8. Tensile and fatigue properties of 17–4 PH stainless steel at high temperatures10.1007/s11661-002-0180-8 ↗
9. Effect of strain rate on high-temperature low-cycle fatigue of 17–4 PH stainless steels10.1016/j.msea.2004.08.063 ↗
10. Effect of reverted austenite on mechanical properties of precipitation hardenable 17–4 stainlesssteel10.1016/j.msea.2013.01.011 ↗
11. Additive manufacturing of metals10.1016/j.actamat.2016.07.019 ↗
12. Wire based additive layer manufacturing: Comparison of microstructure and mechanical properties of Ti-6Al-4V components fabricated by laser-beam deposition and shaped metal deposition10.1016/j.jmatprotec.2011.01.018 ↗
13. On the mechanical behaviour of titanium alloy TiAl6V4 manufactured by selective laser melting: Fatigue resistance and crack growth performance10.1016/j.ijfatigue.2012.11.011 ↗
14. A comparison of the tensile, fatigue, and fracture behavior of Ti-6Al-4V and 15–5 PH stainless steel parts made by selective laser melting10.1007/s00170-013-5106-7 ↗
15. Effects of defects in laser additive manufactured Ti-6Al-4V on fatigue properties10.1016/j.phpro.2014.08.120 ↗
16. Microstructure evolution, tensile properties, and fatigue damage mechanisms in Ti-6Al-4V alloys fabricated by two additive manufacturing techniques10.1016/j.proeng.2015.08.007 ↗
17. Fatigue performance of laser additive manufactured Ti–6Al–4V in very high cycle fatigue regime up to 109 cycles10.3389/fmats.2015.00072 ↗
18. Mechanical behavior of additive manufactured, powder-bed laser-fused materials10.1016/j.msea.2015.10.068 ↗
19. Torsional fatigue behavior of wrought and additive manufactured Ti-6Al-4V by powder bed fusion including surface finish effect10.1016/j.ijfatigue.2017.03.002 ↗
20. Multiaxial fatigue behavior of wrought and additive manufactured Ti-6Al-4V including surface finish effect10.1016/j.ijfatigue.2017.03.044 ↗
21. Fatigue performance of additive manufactured TiAl6V4 using electron and laser beam melting10.1016/j.ijfatigue.2016.05.001 ↗
22. Microstructures and properties of 17–4 PH stainless steel fabricated by selective laser melting10.1016/S2238-7854(12)70029-7 ↗
23. Fatigue performance of additive manufactured metallic parts10.1108/13552541311302932 ↗
24. On the fatigue crack growth behavior in 316L stainless steel manufactured by selective laser melting10.1016/j.engfracmech.2014.03.008 ↗
25. Fatigue analysis in selective laser melting: review and investigation of thin-walled actuator housings
26. Effects of process time interval and heat treatment on the mechanical and microstructural properties of direct laser deposited 316L stainless steel10.1016/j.msea.2015.07.056 ↗
27. Effect of processing parameters on microstructure and tensile properties of austenitic stainless steel 304L made by directed energy deposition additive manufacturing10.1016/j.actamat.2016.03.019 ↗
28. Effects of building orientation and heat treatment on fatigue behavior of selective laser melted 17–4 PH stainless steel10.1016/j.ijfatigue.2016.03.014 ↗
29. Fatigue assessment of laser additive manufactured AlSi12 eutectic alloy in the Very High Cycle Fatigue (VHCF) range up to 1E9 cycles10.1016/j.matpr.2016.07.004 ↗
30. Additive manufactured AlSi10Mg samples using Selective Laser Melting (SLM): Microstructure, high cycle fatigue, and fracture behavior10.1016/j.matdes.2011.07.067 ↗
31. Vander Voort. GF, Lucas GM, Manilova EP. Metallography and Microstructures of Stainless steels and Maraging steels, Metallography and Microstructures, Vol 9, ASM Handbook. ASM Int., 2004, p. 670–700.10.31399/asm.hb.v09.a0003767 ↗
32. ASTM International. E606/E606M-12 Standard Test Method for Strain-Controlled Fatigue Testing. West Conshohocken, PA, 2012.
33. Effect of the processing parameters on the proportion of retained austenite in laser surface melted tool steels10.1023/A:1006573620796 ↗
34. Young’s modulus of porous materials10.1007/BF00540451 ↗
35. Damage evolution and failure mechanisms in additively manufactured stainless steel10.1016/j.msea.2015.10.073 ↗
36. Effect of retained austenite on the microstructure and mechanical properties of martensitic precipitation hardening stainless steel10.1023/A:1004626907367 ↗
37. Fatigue: A complex subject- some simple approximations10.1007/BF02321056 ↗
38. Fatigue criterion for general multiaxial loading10.1046/j.1460-2695.2000.00247.x ↗
39. Bannantine · 1990
40. The classification of flaws of metal materials synthesized by the selective laser melting method and the capabilities of nondestructive testing methods for their detection10.1134/S1061830916010022 ↗
41. Benchmark experiments and characteristic cyclic plasticity deformation10.1016/j.ijplas.2007.10.003 ↗
42. Fatigue of AL6XN Stainless Steel10.1115/1.2931154 ↗
43. Multiaxial Fatigue of 16MnR Steel10.1115/1.3008041 ↗
44. Multiaxial fatigue of extruded AZ31B magnesium alloy10.1016/j.msea.2012.03.039 ↗
45. Effect of strain amplitude on tension-compression fatigue behavior of extruded Mg6Al1ZnA magnesium alloy10.1016/j.scriptamat.2010.01.052 ↗
46. An experimental study on cyclic deformation and fatigue of extruded ZK60 magnesium alloy10.1016/j.ijfatigue.2011.08.016 ↗
47. Multiaxial fatigue of extruded AZ61A magnesium alloy10.1016/j.ijfatigue.2010.09.020 ↗
48. Low cycle fatigue behavior of laser melting deposited TC18 titanium alloy10.1016/S1003-6326(13)62772-7 ↗
49. Fatigue of 7075–T651 aluminum alloy10.1016/j.ijfatigue.2007.07.005 ↗
50. Small fatigue crack growth under multiaxial stresses10.1016/j.ijfatigue.2013.02.002 ↗