Comparison of Strengthening Methods for Self-Compacting Concrete Slabs against Blast Loads using EBR and NSM Technique
Source abstract
Abstract
This study examines the blast resistance of self-compacting concrete (SCC) slabs strengthened using two Fiber Reinforced Polymer (FRP) techniques: externally bonded reinforcement (EBR) and near-surface mounted (NSM). Four SCC slabs were tested: one non-strengthened control slab (NC), two slabs reinforced with polypropylene fibers (FC) and two slabs retrofitted with carbon fiber-reinforced polymer (CFRP) techniques (FC-EBR and FC-NSM). Blast loading was applied using Emulite explosives, with 1231 g used for the control slab and approximately 2070 g for the strengthened specimens. The adopted charge mass was determined by preliminary calibration tests and expressed in TNT equivalency using standard blast scaling laws to ensure the applied load represented a severe, realistic scenario. The experimental program was complemented by advanced finite element simulations performed in ABAQUS, incorporating the Concrete Damage Plasticity (CDP) and Conwep blast models. The FC slab demonstrated an 87.5% reduction in maximum displacement relative to the NC slab, despite being subjected to a higher explosive charge. In addition, the NSM-strengthened slabs exhibited superior performance, achieving a 12.3% reduction in central displacement compared to the EBR system, with maximum displacements of 2.93 mm (FC-EBR) and 2.57 mm (FC-NSM), respectively. This enhancement could be attributed to the improved bond characteristics and reduced debonding risk of the NSM method. Overall, both strengthening techniques effectively increased the slabs’ blast resistance. The close agreement between experimental and numerical results confirms the reliability of the ABAQUS model in predicting structural behavior under blast loading.
Source: openalex_inverted_index · Quality: baseline
Research context
OpenAlex topics: Structural Response to Dynamic Loads · Structural Behavior of Reinforced Concrete · Innovative concrete reinforcement materials
SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.
References (43)
Show source-provided references
1. ABAQUS (2020). (2020). RI, USA: Dassault Systèmes Simulia Corp.
2. Abdesselam, A., Merdas, A., Fiorio, B., & Chikh, N.-E. (2023). Experimental and numerical study on RC beams strengthened by NSM using CFRP reinforcements. Periodica Polytechnica. Civil Engineering, 67(4), 1214–1233.
3. ACI 237R-07. (2007). Self-Consolidating Concrete.
4. ACI 440.2R-02. (2017). Guide for the Design and Construction of Externally Bonded FRP Systems for Strengthening Concrete Structures.
5. Alaa Al Nussairi. (2018). Characterising the Static and Impact Load Resistance of One-Way RC Slabs Strengthened by NSM CFRP Rods. University of Bristol.
6. Ansari, A., Shariatmadar, H., & Beydokhti, E. Z. (2023). Comparison between EBR method and a NSM new technique for strengthening concrete beam-column joints. Iranian Journal of Science and Technology, Transactions of Civil Engineering, 47(6), 3399–3413.10.1007/s40996-023-01151-5 ↗
7. Chen, L., Sun, W., Chen, B., Xu, S., Liang, J., Ding, C., & Feng, J. (2020). A comparative study on blast-resistant performance of steel and PVA fiber-reinforced concrete: Experimental and numerical analyses. Crystals, 10(8), 707.10.3390/cryst10080707 ↗
8. Coughlin, A. M., Musselman, E. S., Schokker, A. J., & Linzell, D. G. (2010). Behavior of portable fiber reinforced concrete vehicle barriers subject to blasts from contact charges. International Journal of Impact Engineering, 37(5), 521–529.10.1016/j.ijimpeng.2009.11.004 ↗
9. Drdlová, M., Popovič, M., & Koutný, O. (2018). Blast resistance of hybrid fibre reinforced concrete containing polyvinyl alcohol, polypropylene and steel fibres with various shape parameters. The European Physical Journal Special Topics, 227(1), 111–126.10.1140/epjst/e2018-00061-y ↗
10. Effiong, J. U., & Ede, A. N. (2022). Experimental investigation on the strengthening of reinforced concrete beams using externally bonded and near-surface mounted natural fibre reinforced polymer composites—a review. Materials, 15(17), 5848.10.3390/ma15175848 ↗
11. Fang, Q., & Zhang, J. (2013). Three-dimensional modelling of steel fiber reinforced concrete material under intense dynamic loading. Construction and Building Materials, 44, 118–132. https://doi.org/10.1016/j.conbuildmat.2013.02.06710.1016/j.conbuildmat.2013.02.067 ↗
12. Guler, S., Akbulut, Z. F., Siad, H., & Lachemi, M. (2021). Effect of macro polypropylene, polyamide and steel fibers on the residual properties of SCC at ambient and elevated temperatures. Construction and Building Materials, 289, Article 123154. https://doi.org/10.1016/j.conbuildmat.2021.12315410.1016/j.conbuildmat.2021.123154 ↗
13. Hamdy, A. E., Abdalla, H. A., Abdelhamed, G. D., & Elansary, A. A. (2025). Experimental and numerical behavior of strengthened reinforced concrete slabs. Journal of Engineering and Applied Science, 72(1), 38.10.1186/s44147-025-00604-0 ↗
14. Han, Z., Qu, W., & Zhu, P. (2023). Research on hybrid FRP–steel-reinforced concrete slabs under blast load. Buildings, 13(4), 1058.10.3390/buildings13041058 ↗
15. Hosseini, M., Jian, B., Zhang, J., Li, H., Lorenzo, R., Hosseini, A., Ghosh, P., Shen, F., Yang, D., & Wang, Z. (2023). Numerical study on the behaviour of hybrid FRPs reinforced RC slabs subjected to blast loads. Journal of Renewable Materials, 11(9), 3517.10.32604/jrm.2023.028164 ↗
16. International Federation for Structural Concrete, fib B. 14. (2001). Externally Bonded FRP Reinforcement for RC Structures.
17. Jackson, C. M., Jacques, E., & Saatcioglu, M. (2022). Blast retrofit of one-way reinforced concrete members using externally bonded FRP and FRP anchorage. International Journal of Protective Structures, 13(2), 209–235.10.1177/20414196221087347 ↗
18. Karlos, V., Solomos, G., & Larcher, M. (2016). Analysis of the blast wave decay coefficient using the Kingery-Bulmash data. International Journal of Protective Structures, 7(3), 409–429.10.1177/2041419616659572 ↗
19. Kingery, C. N., & Bulmash, G. (1984). Airblast parameters from TNT spherical air burst and hemispherical surface burst. US Army Armament and Development Center, Ballistic Research Laboratory.
20. Li, J., Wu, C., & Hao, H. (2015). An experimental and numerical study of reinforced ultra-high performance concrete slabs under blast loads. Materials & Design, 82, 64–76.10.1016/j.matdes.2015.05.045 ↗
21. Li, J., Wu, C., Hao, H., Wang, Z., & Su, Y. (2016). Experimental investigation of ultra-high performance concrete slabs under contact explosions. International Journal of Impact Engineering, 93, 62–75.10.1016/j.ijimpeng.2016.02.007 ↗
22. Liu, J., Wei, J., Li, J., Su, Y., & Wu, C. (2024). A comprehensive review of ultra-high performance concrete (UHPC) behaviour under blast loads. Cement and Concrete Composites, 148, Article 105449.10.1016/j.cemconcomp.2024.105449 ↗
23. Luccioni, B., Isla, F., Codina, R., Ambrosini, D., Zerbino, R., Giaccio, G., & Torrijos, M. C. (2018). Experimental and numerical analysis of blast response of High Strength Fiber Reinforced Concrete slabs. Engineering Structures, 175, 113–122.10.1016/j.engstruct.2018.08.016 ↗
24. Maazoun, A., Belkassem, B., Reymen, B., Matthys, S., Vantomme, J., & Lecompte, D. (2018). Blast response of RC slabs with externally bonded reinforcement: Experimental and analytical verification. Composite Structures, 200, 246–257.10.1016/j.compstruct.2018.05.102 ↗
25. Maghsoudi, M., & Maghsoudi, A. A. (2017). Moment redistribution and ductility of CFRP strengthened and non-strengthened unbonded post-tensioned indeterminate I-beams composed of UHSSCC. Composite Structures, 174, 196–210.10.1016/j.compstruct.2017.04.057 ↗
26. Makhlouf, M. H., El-Azab, I. A., & Mansour, M. H. (2024). Flexural improvement of RC slabs by FRP or steel using different strengthening systems and novel anchoring techniques. International Journal of Concrete Structures and Materials, 18(1), 45.10.1186/s40069-024-00683-y ↗
27. Mao, L., Barnett, S., Begg, D., Schleyer, G., & Wight, G. (2014). Numerical simulation of ultra high performance fibre reinforced concrete panel subjected to blast loading. International Journal of Impact Engineering, 64, 91–100. https://doi.org/10.1016/j.ijimpeng.2013.10.00310.1016/j.ijimpeng.2013.10.003 ↗
28. Měrková, A., Kheml, P., Hala, P., Sovják, R., Leicht, L., Máca, P., & Beckmann, B. (2025). Influence of protective layers on the resistance of concrete structures under blast and impact loading. https://doi.org/10.21012/FC12.114510.21012/FC12.1145 ↗
29. Millard, S. G., Molyneaux, T. C. K., Barnett, S. J., & Gao, X. (2010). Dynamic enhancement of blast-resistant ultra high performance fibre-reinforced concrete under flexural and shear loading. International Journal of Impact Engineering, 37(4), 405–413.10.1016/j.ijimpeng.2009.09.004 ↗
30. Nam, J., Kim, H., & Kim, G. (2017). Experimental investigation on the blast resistance of fiber-reinforced cementitious composite panels subjected to contact explosions. International Journal of Concrete Structures and Materials, 11(1), 29–43.10.1007/s40069-016-0179-y ↗
31. Nam, J.-W., Kim, H.-J., Kim, S.-B., Yi, N.-H., & Kim, J.-H.J. (2010). Numerical evaluation of the retrofit effectiveness for GFRP retrofitted concrete slab subjected to blast pressure. Composite Structures, 92(5), 1212–1222.10.1016/j.compstruct.2009.10.031 ↗
32. Ohkubo, K., Beppu, M., Ohno, T., & Satoh, K. (2008). Experimental study on the effectiveness of fiber sheet reinforcement on the explosive-resistant performance of concrete plates. International Journal of Impact Engineering, 35(12), 1702–1708.10.1016/j.ijimpeng.2008.07.022 ↗
33. Padhi, A. P., Bhandari, V., Chakraborty, S., Kumar, V., Chakrabarti, A., & Chowdhury, R. (2022). A New Deep Learning Accelerated Blast Loading Effect Analysis. International Symposium on Plasticity and Impact Mechanics, 197–203.10.1007/978-981-99-6255-6_17 ↗
34. Pham, T. M., & Hao, H. (2016). Review of concrete structures strengthened with FRP against impact loading. Structures, 7, 59–70.10.1016/j.istruc.2016.05.003 ↗
35. Qsymah, A., & Ayasrah, M. (2024). Finite element analysis of two-way reinforced concrete slabs strengthened with FRP under flexural loading. Buildings, 14(11), 3389.10.3390/buildings14113389 ↗
36. Shirbhate, P. A., & Goel, M. D. (2020). A critical review of tnt equivalence factors for various explosives. Recent Advances in Computational Mechanics and Simulations: Volume-I: Materials to Structures, 471–478.10.1007/978-981-15-8138-0_36 ↗
37. Simoens, B., Lefebvre, M. H., & Minami, F. (2011). Infuence of different parameters on the TNT-equivalent of an explosion. Central European Journal of Energetic Materials, 8(1), 53–67.
38. Swisdak Jr, M. M. (1994). Simplified Kingery airblast calculations.
39. Teng, J.-G., Chen, J.-F., Smith, S. T., & Lam, L. (2002). FRP: strengthened RC structures.
40. Wei, T., & Hargather, M. J. (2021). A new blast wave scaling. Shock Waves, 31(3), 231–238. https://doi.org/10.1007/s00193-021-01012-y10.1007/s00193-021-01012-y ↗
41. Xiao, Y., Chen, Z., Zhou, J., Leng, Y., & Xia, R. (2017). Concrete plastic-damage factor for finite element analysis: Concept, simulation, and experiment. Advances in Mechanical Engineering, 9(9), Article 1687814017719642. https://doi.org/10.1177/168781401771964210.1177/1687814017719642 ↗
42. Zhang, C., & Abedini, M. (2023). Evaluation of near surface mounted (NSM) FRP technique for strengthening of reinforced concrete slabs. Advances in Concrete Construction, 16(4), 205–216.
43. Zhao, C. F., & Chen, J. Y. (2013). Damage mechanism and mode of square reinforced concrete slab subjected to blast loading. Theoretical and Applied Fracture Mechanics, 63, 54–62. https://doi.org/10.1016/j.tafmec.2013.03.00610.1016/j.tafmec.2013.03.006 ↗