γ-irradiation effect on the mechanical properties of in situ specimens made of structural epoxy adhesive and comparison with adhesive bulk behavior
Source abstract
Abstract
This work examines the effects of γ -irradiation (up to 500 kGy ) on the mechanical behavior of aluminum in situ specimens bonded with 3M TM Scotch-Weld TM EC-2216 B/A Gray, a commercial two-part epoxy adhesive. Shear tests were performed, from which failure data and incipient axial stiffness were obtained. The results were compared to those of dedicated finite element models that had been tuned with the previously obtained bulk cohesive properties of the adhesive. Analytic models to evaluate stress distribution in the adhesive and joints axial stiffness were applied to validate the developed models and to explain the relatively small stiffness variance (observed both in experimental and numerical analyses results) compared to that of the adhesive Young’s modulus. On the whole, the adhesive showed a good tolerance to radiation in the interval studied, as already observed for bulk specimens. Finite element models were found to be accurate in predicting of the stiffness for the entire deformative field, while they overestimated the failure loads and displacements also applying unconservative failure criteria. This is very likely due to the significant number of defects found on the fracture surfaces of bulk specimens.
Source: expertdata · Quality: candidate unverified · Source record ↗
Research context
OpenAlex topics: Mechanical Behavior of Composites · Fatigue and fracture mechanics · Electronic Packaging and Soldering Technologies
SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.
References (22)
Show source-provided references
1. Organic polymer materials in the space environment10.1016/j.paerosci.2016.02.002 ↗
2. Glossary of basic terms in polymer science (IUPAC Recommendations 1996)10.1351/pac199668122287 ↗
3. Empirical investigations on the effects of ionizing radiation on epoxy structural adhesives and resins: An overview
4. 2018
5. Post-cure and γ-irradiation effects on the elastoplastic behavior of structural epoxy adhesive bulk specimens10.1016/j.ijadhadh.2022.103225 ↗
6. Guarino · 2001
7. Manufacture of quality specimens
8. Mechanical properties of adhesives in situ and in bulk10.1016/0143-7496(94)90018-3 ↗
9. 2019
10. 2017
11. Bonded joints with composite adherends. Part I. Effect of specimen configuration, adhesive thickness, spew fillet and adherend stiffness on fracture10.1016/j.ijadhadh.2005.03.015 ↗
12. Influence of the spew fillet and other parameters on the stress distribution in the single lap joint10.1080/00218468108073182 ↗
13. Experimental and numerical investigation of the static response of environmentally aged adhesively bonded joints10.1016/j.ijadhadh.2012.08.007 ↗
14. Cold-curing epoxy resins: Aging and environmental effects. II-mechanical properties10.1515/POLYENG.2001.21.4.349 ↗
15. Baccaro · 2019
16. Ramberg · 1943
17. Schwer · 2008
18. Analytical models of adhesively bonded joints — Part I: Literature survey10.1016/j.ijadhadh.2008.06.005 ↗
19. The Stresses in Cemented Joints10.1115/1.4009336 ↗
20. Effect of adherend recessing on the tensile strength of single lap joints10.1080/00218464.2013.766132 ↗
21. Analytical stiffness analysis of adhesively bonded single-lap joints subjected to out-of-plane deflection due to tensile loading
22. Effect of poisson’s ratio strains in adherends on stresses of an idealized lap joint10.1243/03093247V082134 ↗