Adhesive composite joint reinforcement using button shape interlocking features
Source abstract
Abstract
Abstract The composite panels have high strength-to-weight ratio. Adhesive connections are the most common methods of joining in composites. The composite connections are being used in industries such as aerospace, automotive, marine and etc. Low strength is one of the disadvantages of the adhesive connections. Strength improvement is considered in different researches. In this study, using a button shape edge is considered as a new method for strengthening the adhesively bonded composite connections. The effect of geometrical parameters of the button shape edge was investigated numerically and experimentally. These parameters are the radius and height of the button. The influences of the type of the adhesive was also considered in this study. Increasing the radius up to six times the adherent thickness, increased the strength of the joints, significantly. For the optimized geometry (Height = Radius = six times the adherent thickness), the load-bearing capability of the adhesive joint increased up to 300%. Numerical studies showed that the maximum of peel and shear stresses also reduce about 160% and 70%, respectively, for the optimal case. It was also obtained that the height diminution increased the peel and shear stresses in the button shape connections.
Source: openaire · Quality: candidate unverified · Source record ↗
Research context
OpenAlex topics: Mechanical Behavior of Composites · Structural Load-Bearing Analysis · Composite Structure Analysis and Optimization
SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.
References (32)
Show source-provided references
1. MWCNT–epoxy nanocomposite sensors for structural health monitoring10.3390/electronics7080143 ↗
2. Reedy · J. Adhes. Sci. Technol. · 1996 · 10 · 3310.1163/156856196X00436 ↗
3. Investigation of mechanical behavior of alfa and gamma nano- alumina/epoxy composite made by VARTM
4. Experimental investigation of the effects of adhesive defects on the single lap joint strength10.1016/j.ijadhadh.2017.08.005 ↗
5. Experimental investigation of nano-alumina effecton the filling time in VARTM process10.4314/jfas.v8i2s.146 ↗
6. Effect of residual stresses on crack behaviour in single edge bending specimens10.1111/j.1460-2695.2012.01704.x ↗
7. Parametric study of adhesive joints with composites10.1016/j.ijadhadh.2012.01.019 ↗
8. Influence of boundary conditions on stress distributions in a single-lap adhesively bonded joint10.1016/j.ijadhadh.2014.01.009 ↗
9. Investigating the performances of stepwise patched double lap joint10.1016/j.ijadhadh.2013.01.005 ↗
10. FEM stress analysis and strength prediction of scarf adhesive joints under static bending moments10.1016/j.ijadhadh.2013.02.010 ↗
11. Stress analysis and strength evaluation of scarf adhesive joint with dissimilar adherends subjected to static tensile loadings10.1299/jmmp.3.1033 ↗
12. Use of epoxy/multiwalled carbon nanotubes as adhesives to join graphite fibre reinforced polymer composites10.1088/0957-4484/14/7/316 ↗
13. Performance of bi-adhesive bonded aluminium lap joints10.1016/S0143-7496(03)00024-1 ↗
14. Experimental investigation of nanoparticles effects on cohesive model and bridging laws of mode I fracture in the adhesive joints10.1080/01694243.2017.1284639 ↗
15. Variable modulus adhesives: an approach to optimised joint performance10.1016/j.ijadhadh.2004.08.002 ↗
16. Experimental and numerical study on the composite adhesive joint reinforcement using wavy edge10.1080/01694243.2017.1395578 ↗
17. A reinforcing technique for the adhesive bonded composite joints using metallic wires10.1080/01694243.2017.1290573 ↗
18. The optimization of comeld joints: a novel technique for bonding composites and metal
19. Evaluation of different lap-shear joint geometries for automotive applications10.1016/j.ijadhadh.2006.09.016 ↗
20. Stress analysis on a wavy-lap bonded joint for composites10.1016/j.ijadhadh.2003.12.001 ↗
21. Adhesively bonded single lap joints with non-flat interfaces10.1016/j.ijadhadh.2011.09.004 ↗
22. The strength of the adhesively bonded step-lap joints for different step numbers10.1016/j.compositesb.2014.06.023 ↗
23. A three-dimensional finite element stress analysis and strength prediction of stepped-lap adhesive joints of dissimilar adherends subjected to bending moments10.1016/j.ijadhadh.2010.01.006 ↗
24. Numerical design and multiobjective optimisation of novel adhesively bonded joints employing interlocking surface morphology10.1016/j.ijadhadh.2017.06.002 ↗
25. Mechanical performance and failure behaviour of miniature aluminium joints with novel interlocking reinforcement10.1016/j.ijadhadh.2019.102431 ↗
26. Characterization of cohesive model and bridging laws in mode I and II fracture in nano composite laminates10.15282/jmes.12.4.2018.24.0370 ↗
27. Trapezoidal traction–separation laws in mode II fracture in nano-composite and nano-adhesive joints10.1177/0731684418761001 ↗
28. Novel study on keyhole less friction stir spot welding of Al 2024 reinforced with alumina nanopowder10.1007/s00170-018-3142-z ↗
29. Study on the new friction stir spot weld joint reinforcement technique on 5754 aluminum alloy10.1177/0954406217729419 ↗
30. 2019
31. Investigation of drilling composite sandwich structures10.1007/s00170-014-6427-x ↗
32. Effects of nanoparticles on nanocomposites mode I and II fracture: a critical review10.1002/9781119526445.ch12 ↗