Study of laser surface texturing on the adhesion properties of SHF-2D epoxy zinc paint
Source abstract
Abstract
In this paper, laser surface texturing (LST) was performed on the surface of 6061 aluminum alloy using a pulsed laser, and then SHF-2D zinc epoxy coating (SP) was applied to the LST-processed surface. The adhesion performance under different laser spot overlap rates was investigated. The results show that the LST surface can increase the adhesion strength by 2∼3 times. The pattern of the spatter produced by laser irradiation determines the adhesion strength. The higher the height and the larger the spatter, the better it locks into the SP, thus effectively increasing the adhesion strength. The adhesion strength is greatest (up to 15.98 MPa) at a laser spot ratio of 10 %, due to the formation of an “upside-down” spatter. This splatter effectively locks into the paint in place, thereby greatly increasing the bond strength between the paint and the substrate.
Source: expertdata · Quality: candidate unverified · Source record ↗
Research context
OpenAlex topics: Laser Material Processing Techniques · Corrosion Behavior and Inhibition · Surface Modification and Superhydrophobicity
SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.
References (18)
Show source-provided references
1. Soft matter laser micro-texturing for friction reduction: an experimental investigation10.1016/j.triboint.2019.03.001 ↗
2. S. Ito, K. Takahashi, S. Sasaki, Generation mechanism of friction anisotropy by surface texturing under boundary lubrication, Tribol. Int. Available online 10 February 2019;.10.1016/j.triboint.2019.02.006 ↗
3. Effects of micro-knurling and femtosecond laser micro texturing on aluminum long-term surface wettability10.1016/j.apsusc.2019.02.025 ↗
4. Effect of liquid nitrogen cooling on grain growth and properties of laser cladding in-situ (Ti, Nb)C/Ni composite coatings
5. Laser surface texturing (LST) treatment before thermal spraying: a new process to improve the substrate-coating adherence10.1016/j.surfcoat.2010.07.044 ↗
6. Pre-/During-/Post-Laser processes to enhance the adhesion and mechanical properties of thermal-sprayed coatings with a reduced environmental impact10.1007/s11666-011-9629-x ↗
7. Laser surface texturing to enhance adhesion bond strength of spray coatings – cold spraying, wire-arc spraying, and atmospheric plasma spraying10.1016/j.surfcoat.2017.05.007 ↗
8. Critical influences of particle size and adhesion on the powder layer uniformity in metal additive manufacturing10.1016/j.jmatprotec.2018.10.037 ↗
9. Laser surface alloying on aluminum and its alloys: a review10.1016/j.optlaseng.2017.07.006 ↗
10. Fibre laser cutting of polycaprolactone sheet for stents manufacturing: a feasibility study10.1016/j.optlastec.2017.03.048 ↗
11. Laser assisted additive manufacturing of continuous fiber reinforced thermoplastic composites10.1016/j.matdes.2017.06.013 ↗
12. Fibre laser cutting of polymer tubes for stents manufacturing10.1016/j.promfg.2017.09.038 ↗
13. Effect of anisotropy in the build direction and laser-scanning conditions on characterization of short-glass-fiber-reinforced PBT for laser sintering10.1016/j.optlastec.2019.01.012 ↗
14. Quantifying the spread in crystallographic textures due to transients in strain path in shot-peening
15. Influence of combined shot peening and PEO treatment on corrosion fatigue behavior of 7A85 aluminum alloy10.1016/j.apsusc.2019.04.242 ↗
16. Evaluating oxidation behavior of amorphous aluminum phosphate coating10.1016/j.apsusc.2018.06.087 ↗
17. Effect of zinc soaps of rubber seed oil (RSO) and/or epoxidised rubber seed oil (ERSO) on the thermal stability of PVC plastigels10.1016/j.polymdegradstab.2007.05.002 ↗
18. Improvement of adhesion performance between aluminum alloy sheet and epoxy based on anodizing technique[J]