Characterization of bamboo particleboard bonded with Nelumbo nucifera seed starch-citric acid-based adhesive
Source abstract
Abstract
This study evaluates bio-based Nelumbo nucifera starch-citric acid adhesives as sustainable alternatives to urea-formaldehyde for bamboo particleboard fabrication. Particleboards were produced using Semantan bamboo ( Gigantochloa scortechinii) particles with three adhesive formulations: BPS100 (100 % starch), BPS75 (75 % starch, 25 % citric acid), and BPS50 (50 % starch, 50 % citric acid), targeting a density of 0.80 g/cm³ according to ASTM D1037 standards. Physical properties, including thickness swelling and water absorption, were assessed alongside mechanical properties such as modulus of rupture (MOR) and internal bond (IB) strength. The BPS50 formulation exhibited the lowest thickness swelling (76.85 %) and water absorption (134.5 %), as well as the highest MOR (5.448 MPa) and IB strength (0.372 MPa), outperforming both BPS75 and BPS100. However, the MOR value remains below the minimum required standard for general purposed particleboard, indicating the need for further development. FTIR analysis confirmed the formation of ester linkages between starch and citric acid, with enhanced carbonyl signals correlating with improved properties. While these findings highlight the potential of starch-citric acid adhesives as renewable, formaldehyde-free bio-adhesives for lignocellulosic particleboard composites, further optimization is necessary to meet industrial performance standards.
Source: expertdata · Quality: candidate unverified · Source record ↗
Research context
OpenAlex topics: Natural Fiber Reinforced Composites · Lignin and Wood Chemistry · Advanced Cellulose Research Studies
SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.
References (60)
Show source-provided references
1. Latest advancements in high-performance bio-based wood adhesives: a critical review10.1016/j.jmrt.2022.10.156 ↗
2. Oil revenue and production cost disconnect and its impact on the environment: economic globalization in Asia-Pacific economic cooperation countries10.1016/j.gsf.2023.101772 ↗
3. Chapter 14 - formaldehyde: Risk assessment, environmental, and health hazard
4. Respiratory effects due to occupational exposure to formaldehyde: systematic review with meta-analysis10.4103/0019-5278.32461 ↗
5. An overview of different types and potential of bio-based adhesives used for wood products10.1016/j.ijadhadh.2021.102992 ↗
6. Subasi · 2020
7. Low formaldehyde binders for mineral wool insulation: a review
8. Environmentally friendly starch-based adhesives for bonding high-performance wood composites: a review10.3390/f13101614 ↗
9. A review of biodegradable thermoplastic starches, their blends and composites: recent developments and opportunities for single-use plastic packaging alternatives
10. Thermoplastic starch: a possible biodegradable food packaging material—a review10.1111/jfpe.12447 ↗
11. Chemical and physical modifications of starch for renewable polymeric materials
12. Adhesive and flame-retardant properties of starch/Ca(2+) gels with different amylose contents10.3390/molecules28114543 ↗
13. Structural and physicochemical properties of lotus seed starch-chlorogenic acid complexes prepared by microwave irradiation10.1007/s13197-020-04881-w ↗
14. Physicochemical properties and molecular structure of lotus seed starch10.1016/j.carbpol.2022.120515 ↗
15. High amylose-based bio composites: structures, functions and applications10.3390/polym14061235 ↗
16. Granular architecture of lotus seed starch and its impact on physicochemical properties10.1016/j.foodres.2023.113564 ↗
17. Prediction of enhanced interfacial bonding strength for basalt fiber/epoxy composites by micromechanical and thermomechanical analyses10.1016/j.compositesa.2020.106208 ↗
18. The characteristics of citric acid-bonded composite boards produced from alkaline-modified fibrovascular bundle of salacca sumatrana fronds10.1080/15440478.2024.2315505 ↗
19. Effect of water absorption on the mechanical properties of bamboo/glass-reinforced polybenzoxazine hybrid composite
20. Importance of interfacial adhesion condition on characterization of plant-fiber-reinforced polymer composites: a review10.3390/polym13030438 ↗
21. Green preparation of citric acid crosslinked starch for improvement of physicochemical properties of Cyperus starch10.4274/tjps.galenos.2019.65624 ↗
22. Properties of particleboard from oil palm biomasses bonded with citric acid and tapioca starch10.3390/polym13203494 ↗
23. Effect of hot-pressing and hydrothermal parameters on recycled wood particles and particleboards
24. A study of the influence of press parameters on particleboards' performance10.1007/s00107-020-01507-y ↗
25. Influence of formulation and hot-pressing conditions on the performance of bio-based molasses adhesive for plywood10.32604/jrm.2024.052052 ↗
26. 2020
27. Interface and bonding mechanisms of plant fibre composites: an overview10.1016/j.compositesb.2016.06.055 ↗
28. Effect of citric acid induced crosslinking on the structure and properties of potato starch/chitosan composite films10.1016/j.foodhyd.2019.105208 ↗
29. Preparation and physicochemical characterization of starch/pectin and chitosan blend bioplastic films as future food packaging materials10.1016/j.jece.2023.111825 ↗
30. Effect of chemical modification with citric acid on the physicochemical properties and resistant starch formation in different starches
31. The effect of citric acid concentrations on the mechanical, thermal, and structural properties of starch edible films10.1111/ijfs.16933 ↗
32. An empirical IR frequency map for ester C=O stretching vibrations10.1021/acs.jpca.6b02887 ↗
33. Utilization of sweet sorghum bagasse and citric acid for manufacturing of particleboard I: effects of pre-drying treatment and citric acid content on the board properties10.1016/j.indcrop.2016.01.042 ↗
34. Utilization of sweet sorghum bagasse and citric acid for manufacturing of particleboard II: influences of pressing temperature and time on particleboard properties10.1007/s10086-016-1605-0 ↗
35. Citric acid: an ecofriendly cross-linker for the production of functional biopolymeric materials
36. Citric acid crosslinked soluble soybean polysaccharide films for active food packaging applications10.1016/j.foodchem.2023.138009 ↗
37. Modification of novel bio-based adhesive made from citric acid and sucrose by ZnCl210.1016/j.ijadhadh.2021.102866 ↗
38. Utilization of sweet sorghum bagasse and citric acid in the manufacturing of particleboard. III: influence of adding sucrose on the properties of particleboard10.15376/biores.12.4.7498-7514 ↗
39. Advances in the modification of starch via esterification for enhanced properties10.1007/s10924-020-02006-0 ↗
40. How can cellulosic fibers enhance adhesion in engineered wood?10.1016/j.mser.2024.100852 ↗
41. Effect of starch addition on properties of citric acid-bonded particleboard made from bamboo10.15376/biores.12.4.8068-8077 ↗
42. Shah · 2023 · 103
43. Effects of heat-moisture treatment after citric acid esterification on structural properties and digestibility of wheat starch, A- and B-type starch granules10.1016/j.foodchem.2018.08.079 ↗
44. Effect of citric acid on swelling resistance and physicochemical properties of post-crosslinked electrospun polyvinyl alcohol fibrous membrane10.3390/polym15071738 ↗
45. Formulation and characterization of crosslinked polyvinyl alcohol (PVA) membranes: effects of the crosslinking agents10.1007/s00289-020-03142-2 ↗
46. High water resistance polyvinyl alcohol hydrogel film prepared by melting process combining with citric acid cross-linking
47. Effect of citric acid cross linking on the mechanical, rheological and barrier properties of chitosan10.3390/molecules27165118 ↗
48. Fabrication and characterization of citric acid crosslinked, sea buckthorn leaves extract incorporated PVA-based films with improved antioxidative and UV-shielding properties for food packaging applications10.1007/s41783-024-00174-1 ↗
49. Effect of chemical composition of bamboo fibers on water sorption10.1007/s10570-021-03988-3 ↗
50. Mechanical behavior of bamboo, and its biomimetic composites and structural members: a systematic review10.1007/s42235-023-00430-1 ↗
51. Starch-derived superabsorbent polymers in agriculture applications: an overview10.1007/s00289-021-03842-3 ↗
52. Current status and perspectives of starch powders modified by cold plasma: a review10.1007/s10924-023-03027-1 ↗
53. Lignin biosynthesis and its diversified roles in disease resistance10.3390/genes15030295 ↗
54. Functional surfaces, films, and coatings with lignin - a critical review10.1039/D2RA08179B ↗
55. Hydrophobic treatment of natural fibers and their composites—a review10.1177/1528083716654468 ↗
56. Effect of mechanical activation on starch crosslinking with citric acid10.1016/j.ijbiomac.2021.06.139 ↗
57. Microbond fibre bundle pullout technique to evaluate the interfacial adhesion of polyethylene and polypropylene self reinforced composites10.1186/s40563-019-0121-z ↗
58. Synthesis, characterization, and application of starch-based adhesives modified with itaconic acid and N-hydroxyethyl acrylamide10.1016/j.indcrop.2023.116524 ↗
59. Influence of citric acid addition and fiber treatment on tensile properties of ramie fiber reinforced poly-lactic acid (PLA) green composite
60. Influence of citric acid on the bond strength of beech wood10.3390/polym13162801 ↗