Carbon nanotube reinforced epoxy based adhesive: Correlations between chemical functional and failure modes
Source abstract
Abstract
This paper addresses correlational studies among failure mode analysis, fracture morphology, and the chemical changes for a single-lap bonded joint (SLJ) based on an industrial adhesive. The SLJ bonded joint was selected due to its stress combination inside the adhesive, i.e., peel and shear. The increase in the Fourier-transform Infrared (FTIR) intensity of chemical functional, i.e., rocking of CH 2 group, C–O–C stretching of oxirane group, C–C stretching vibration, C=C aromatic ring stretching, are related to the ductile-like fracture morphology due to more molecular mobility. At meanwhile, the increase in intensity of asymmetrical vibration CH 2 and O–H stretching vibrations are related to brittle-like morphology fracture. The cohesive failure is related to the ductile-like failure morphology, while the adhesive failure is linked to brittle-like morphology fracture. At room temperature, then best option is the 0.25 wt % carbon nanotubes (CNT), as cohesive failure modes are prevalent. The addition of carbon nanotubes to the industrial adhesive reduces the high temperature environmental degradation. However, the addition of carbon nanotubes had small influence into glass transition temperature variations. Considering the amount of CNT dispersed into the epoxy system, and the 100 °C long time exposures, it seems that the 1.0 wt % CNT content is the best option. The reasons for such differences are due to changes at chemical functional caused by the prolonged exposure to temperature higher than the glass transition temperature. Such changes were identified by the FTIR spectroscopy analysis.
Source: expertdata · Quality: candidate unverified · Source record ↗
Research context
OpenAlex topics: Mechanical Behavior of Composites · Carbon Nanotubes in Composites · Force Microscopy Techniques and Applications
SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.
References (39)
Show source-provided references
1. Continuum damage modelling of environmental degradation in joints bonded with EA9321 epoxy adhesive10.1016/j.ijadhadh.2007.08.005 ↗
2. Strength and failure analysis of adhesive single-lap joints under shear loading: effects of surface morphologies and overlap zone parameters10.1016/j.jmapro.2020.04.042 ↗
3. Adhesive selection for single lap bonded joints: experimentation and advanced techniques for strength prediction10.1080/00218464.2014.994703 ↗
4. Effect of thermal aging on the mechanical performance of timber-timber single-lap adhesive joints10.1016/j.ijadhadh.2021.102883 ↗
5. Improved design for metallic and composite single-lap joints10.2514/1.28934 ↗
6. Stress expressions of single-lap adhesive joints of dissimilar adherends10.1016/S0263-8223(97)00062-7 ↗
7. An experimental and numerical study on adhesive joints for composites10.1016/j.compstruct.2003.09.052 ↗
8. Fatigue behavior of carbon fibre reinforced plastic and aluminum single-lap adhesive joints after the transverse pre-impact10.1016/j.ijfatigue.2020.105973 ↗
9. The key to designing durable adhesively bonded joints10.1016/0010-4361(94)90033-7 ↗
10. An updated review of adhesively bonded joints in composite materials10.1016/j.ijadhadh.2016.10.010 ↗
11. Strength and failure modes of surface treated CFRP secondary bonded single-lap joints in static and fatigue tensile loading regimes10.1016/j.compositesa.2020.105897 ↗
12. A review on the environmental degradation effects on fatigue behaviour of adhesively bonded joints10.1111/ffe.13239 ↗
13. Mechanical behaviour of adhesively bonded composite single lap joints under quasi-static and impact conditions with variation of temperature and overlap10.1177/0021998318766641 ↗
14. Effect of operating temperature on aged single lap bonded joints10.1016/j.dt.2019.05.015 ↗
15. Modeling nanoclay effects into laminates failure strength and porosity10.1016/j.compstruct.2007.12.009 ↗
16. Bending investigation on carbon fiber/epoxy composites nano-modified by graphene10.1590/S1678-58782012000300007 ↗
17. An investigation on industrial adhesive nano-modified by graphene nanoplatelets under extreme environmental conditions10.1016/j.ijadhadh.2021.102982 ↗
18. Tribological investigation of nanographite platelets as additive in anti-wear lubricant: a top-down approach10.1115/1.4027479 ↗
19. The carbon nanotubes effect into single-lap joint failure modes and load capacity: a macromechanical analysis10.1590/1980-5373-mr-2017-0442 ↗
20. Mechanical and electrical properties of graphene and carbon nanotube reinforced epoxy adhesives: experimental and numerical analysis10.1016/j.compositesa.2019.02.027 ↗
21. SikaPower ® -456 LB
22. Standard test method for apparent shear strength of single-lap-joint adhesively bonded metal specimens by tension loading (metal-to-metal)
23. Noncovalent engineering of carbon nanotube surface by imidazolium ionic liquids: a promising strategy for enhancing thermal conductivity of epoxy composites10.1016/j.compositesa.2019.105517 ↗
24. Interface mechanics in carbon nanomaterials-based nanocomposites10.1016/j.compositesa.2020.106212 ↗
25. Improved impact strength of epoxy by the addition of functionalized multiwalled carbon nanotubes and reactive diluent10.1002/app.42587 ↗
26. Standard test methods for cone penetration of lubricating grease using one-quarter
27. Fracture surface and mechanical properties of epoxy composites10.1002/9783527824083.ch10 ↗
28. Effect of different multi-walled carbon nanotubes MWCNTs on mechanical and physical properties of epoxy nanocomposites10.1088/1757-899X/1094/1/012166 ↗
29. Enhanced mechanical and thermal properties of monocomponent high performance epoxy resin by blending with hydroxyl terminated polyethersulfone10.1016/j.polymertesting.2018.05.039 ↗
30. FTIR investigations on hydrolysis and condensation reactions of alkoxysilane terminated polymers for use in adhesives and sealants10.1016/j.ijadhadh.2015.10.014 ↗
31. Reinforcing brittle and ductile epoxy matrices using carbon nanotubes masterbatch10.1016/j.compositesa.2014.02.016 ↗
32. Fracture behavior of epoxy nanocomposites modified with polyol diluent and amino-functionalized multi-walled carbon nanotubes: a loading rate study10.1016/j.compositesa.2013.12.014 ↗
33. Fabrication, characterization, morphological and thermal investigations of functionalized multi-walled carbon nanotubes reinforced epoxy nanocomposites10.1016/j.porgcoat.2020.105962 ↗
34. Effect of carbon nanotube dispersion on glass transition in cross-linked epoxy-carbon nanotube nanocomposites: role of interfacial interactions10.1021/jp401614p ↗
35. Thermo-physical and impact properties of epoxy nanocomposites reinforced by single-wall carbon nanotubes10.1016/j.polymer.2004.05.036 ↗
36. The effect of temperature on the mechanical properties of adhesives for the automotive industry
37. Interpretation of FTIR spectra of polymers and Raman spectra of car paints by means of likelihood ratio approach supported by wavelet transform for reducing data dimensionality10.1007/s00216-015-8558-9 ↗
38. Atomic oxygen degradation mechanisms of epoxy composites for space applications10.1016/j.polymdegradstab.2019.05.026 ↗
39. Effects of temperature and moisture on the fracture behaviour of composite adhesive joints10.1016/j.ijadhadh.2020.102607 ↗