journal article·2021-03

Temperature effects on failure mode of double lap glass-aluminum and glass-GFRP joints with epoxy and acrylic adhesive

Chiara Borsellino, Santi Urso, Tiziana Alderucci, Gianluca Chiappini, Marco Rossi, Placido Munafò

Publisher page

Abstract

Abstract In this experimental study, a series of mechanical tests were conducted on double-lap joint specimens, where glass sheets were adhesively bonded on two different supports, namely aluminum and glass fiber reinforced polymer (GFRP). Five different types of adhesives (three epoxy and two acrylic) were compared and three temperature conditions (room temperature, work temperature and maximum service temperature) were investigated. The main aim is to verify the applicability of this type of junction on civil applications, such as windows, glass facades, and so on. The first part of this study describes the results of tensile tests conducted in order to verify the compatibility of the bonding system at room temperature; the second part illustrates the degradation of the adhesive bonding due to high temperatures; in fact, if used in civil applications, these junctions are generally exposed to severe temperatures that could reach the glass transition temperature of the used adhesive, this leads to the necessity to verify the correct functionality of the adhesive joint. The results evidenced that the mechanical performance of adhesive junctions is considerably reduced as the temperature increases. This phenomenon is more evident in acrylic adhesives rather than epoxy ones. The epoxy adhesives in all tests exhibited the highest load carrying, while the acrylic ones showed the highest joint elongations. Different failure modes, classified as “Adhesive Failure”, “Cohesive Failure”, ‘‘Light-Fiber-Tear Failure” or “Mixed Failure”, were observed at room temperature while, at high temperatures, only “adhesive failure” was observed. The study demonstrates that high temperatures have a remarkable impact on the mechanical properties of adhesive junctions. Such effect should be suitably taken into account in the design and verification phase of components. The research results can be appropriately used in practical applications.
Source: openaire · Quality: candidate unverified · Source record ↗

Research context

OpenAlex topics: Structural Behavior of Reinforced Concrete · Structural Load-Bearing Analysis · Mechanical Behavior of Composites

SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.

References (22)

Show source-provided references
1. Environmental ageing on GFRP pultruded joints: comparison between different adhesives10.1016/j.compstruct.2015.07.067 ↗
2. Recent all-composites and hybrid fiber-reinforced polymer bridges and buildings10.1002/pse.66 ↗
3. Use of FRP pultruded members for electricity transmission towers10.1016/j.compstruct.2013.05.025 ↗
4. Development of a slim window frame made of glass fibre reinforced polyester10.1016/j.enbuild.2010.05.028 ↗
5. Experimental study of the adhesive glass-steel joint behavior in a tensegrity floor10.1016/j.ijadhadh.2018.04.017 ↗
6. Behavior and failure strength of laminated glass beams
7. A review of the present and future utilisation of FRP composites in the civil infrastructure with reference to their important in-service properties10.1016/j.conbuildmat.2010.04.062 ↗
8. Turvey · 2013 · 440
9. Ductile double-lap joints from brittle GFRP laminates and ductile adhesives, part I: experimental investigation10.1016/j.compositesb.2007.02.015 ↗
10. A steel-reinforced hybrid GFRP deck panel for temporary bridges10.1016/j.conbuildmat.2012.02.029 ↗
11. Behavior of pultruded fiber-reinforced polymer beams subjected to concentrated loads in the plane of the web10.1061/(ASCE)CC.1943-5614.0000082 ↗
12. Adhesive joints in glass structures: effects of various materials in the connection, thickness of the adhesive layer, and ageing10.1016/j.ijadhadh.2016.09.007 ↗
13. Mechanical performances of GFRP-steel specimens bonded with different epoxy adhesives, before and after the ageing treatments10.1016/j.compstruct.2017.03.020 ↗
14. Adhesive joints for low- and high-temperature use: an overview10.1080/00218464.2014.943395 ↗
15. A review on the temperature and moisture degradation of adhesive joints
16. Manufacture of adhesive joints and bulk specimens with high temperature adhesives10.1016/S0143-7496(03)00101-5 ↗
17. Uni En 755-2 · 2016
18. ASTM D638 · 2014
19. ASTM D3528-16 Standard test method for strength properties of double lap shear adhesive joints by tension loading.
20. Comparison of fracture behavior between acrylic and epoxy adhesives10.1016/j.ijadhadh.2017.02.011 ↗
21. Strength of adhesively bonded stainless steel joints10.1016/S0143-7496(03)00049-6 ↗
22. ASTM D5573-99. Standard practice for classifying failure modes in fiber reinforced plastic (FRP) joints.