journal article·2020-07

Relationship between the surface free energy and stiffness modulus of bitumen modified with micro-nano-carbon black from end-of-life tires

Rashid Tanzadeh, Gholamali Shafabakhsh

Publisher page

Abstract

Abstract In this research, carbon black (CB) particles were produced from the pyrolysis of crumb rubber (CR), and nano-carbon black (NCB) was obtained from CB particles. A commonly used performance grade (PG) binder (PG 64-22) was modified with different dosages of CB and NCB particles. After the basic laboratory bitumen test, the penetration index and stiffness modulus of the modified bitumen were calculated. The cohesion and adhesion work between different combinations of modified bitumen and aggregates (quartzite, granite, limestone, and sandstone) were measured in the absence and presence of water. Results showed that the penetration index and stiffness modulus of the bitumen modified with CB and NCB particles increased, while the static contact angle decreased. Limestone and quartzite showed the lowest work of adhesion, whereas sandstone demonstrated the highest work of adhesion in wet conditions. According to compatibility parameter (CP) data, limestone and quartzite had the most compatible aggregates-bitumen structure. With the addition of higher CB and NCB percentages, the CP value depicted an increasing trend. Finally, according to two new statistical models, a direct relationship existed between the work of cohesion and stiffness modulus of the modified bitumen.
Source: openaire · Quality: candidate unverified · Source record ↗

Research context

OpenAlex topics: Asphalt Pavement Performance Evaluation · Infrastructure Maintenance and Monitoring · Polymer Nanocomposites and Properties

SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.

References (46)

Show source-provided references
1. Recycling of waste tire rubber in asphalt and portland cement concrete: an overview10.1016/j.conbuildmat.2013.11.027 ↗
2. The influence of crumb rubber modifier (CRM) microstructures on the high-temperature properties of CRM binders10.1080/10298430500373336 ↗
3. Laboratory performance evaluation of warm-mix asphalt containing high percentages of reclaimed asphalt pavement10.3141/2294-11 ↗
4. Heitzman · 1992
5. Epps · 1994
6. Lightly pyrolyzed tire rubber used as potential asphalt alternative10.1016/j.conbuildmat.2016.02.208 ↗
7. Carbon black - its nature and possible effects on the characteristics of bituminous road binders
8. Effects of carbon black on the thermal, mechanical and electrical properties of pitch-matrix composites10.1016/j.carbon.2004.04.005 ↗
9. Mechanistic evaluation of modified asphalt paving mixtures10.1139/l94-101 ↗
10. Comparison of carbon black from pyrolyzed tires to other fillers as asphalt rheology modifiers
11. Modification of bitumen with scrap tire pyrolytic carbon black. Comparison with commercial carbon black Part I: mechanical and rheological properties
12. Performance evaluation of bitumen modified with pyrolysis carbon black made from waste tires10.1016/j.conbuildmat.2016.02.143 ↗
13. Effect of carbon black on the high and low-temperature properties of bitumen
14. Poulikakos · 2003
15. Potential applications of nanotechnology in pavement engineering10.1061/(ASCE)0733-947X(2009)135:10(764) ↗
16. Nanomaterials applied in asphalt modification: a review10.1016/j.jmst.2013.04.008 ↗
17. Nanoclay-modified asphalt materials: preparation and characterization10.1016/j.conbuildmat.2010.06.070 ↗
18. Rheological properties and chemical bonding of asphalt modified with nanosilica10.1061/(ASCE)MT.1943-5533.0000690 ↗
19. Evaluation the effect of nano-TiO2 on the rutting and fatigue behavior of asphalt mixtures10.1016/j.conbuildmat.2013.12.064 ↗
20. Physical, rheological, and aging properties of bitumen containing organic expanded vermiculite and nano-zinc oxide
21. Nanoclay-modified asphalt materials preparation and characterization10.1016/j.conbuildmat.2010.06.070 ↗
22. Evaluation of rheological behavior and performance to permanent deformation of nanomodified asphalt mixtures with carbon nanotubes10.1139/cjce-2015-0546 ↗
23. Physicochemical characterisations of the bitumen–aggregate interface to get a better understanding of stripping phenomena10.1080/14680629.2013.803494 ↗
24. Stripping at the Bitumen−Aggregate interface: a laboratory method to assess the loss of chemical adhesion10.1021/acs.energyfuels.8b03410 ↗
25. Moisture susceptibility of asphalt mixtures. Part 1: Mechanisms10.1080/10298430701792128 ↗
26. An essay on the cohesion of fluids10.1098/rstl.1805.0005 ↗
27. Attractive forces at interfaces10.1021/ie50660a008 ↗
28. Estimation of the surface free energy of polymers10.1002/app.1969.070130815 ↗
29. Bitumen surface energy characterization using a contact angle approach10.1061/(ASCE)0899-1561(2006)18:6(759) ↗
30. Little · 2006
31. Investigation of moisture damage resistance of GTR-modified asphalt binder by static contact angle measurements10.1016/j.conbuildmat.2015.07.032 ↗
32. Using energy parameters based on the surface free energy concept to evaluate the moisture susceptibility of hot mix asphalt10.1080/14680629.2014.990049 ↗
33. Influence of process conditions on product yield of waste tyre pyrolysis- A review10.1007/s11814-016-0126-2 ↗
34. Investigating fatigue behavior of nanoclay and nano hydrated lime modified bitumen using LAS test10.1061/(ASCE)MT.1943-5533.0001376 ↗
35. Optimized experimental design for natural clinoptilolite zeolite ball milling to produce nanopowders10.1016/j.powtec.2010.05.034 ↗
36. Investigating the effect of nanoparticles on the rutting behaviour of hot-mix asphalt
37. Way · 2011
38. A study of moisture damage in plastomeric polymer modified asphalt binder using functionalized AFM tips
39. Ghabchi · 2013
40. Evaluation for warm mix additive-modified asphalt binders using spectroscopy techniques10.1061/(ASCE)MT.1943-5533.0000562 ↗
41. Assessment of a sessile drop device and a new testing approa measuring contact angles on aggregates and asphalt binders10.1061/(ASCE)MT.1943-5533.0000852 ↗
42. The rheological properties of asphaltic bitumens
43. Radovskiy · 2018
44. Contact angle measurement and contact angle interpretation10.1016/S0001-8686(98)00087-6 ↗
45. Bitumen surface energy characterization using a contact angle Approach10.1061/(ASCE)0899-1561(2006)18:6(759) ↗
46. Influence of nano silica and diatomite on the physicochemical and mechanical properties of the binder at unaged and oxidized conditions10.1016/j.conbuildmat.2016.09.140 ↗