Degradation of ferritic X10CrAlSi18 stainless steel caused by slurry
Source abstract
Abstract
Abstract The slurry erosion tests of ferritic X10CrAlSi18 steel were carried out using a slurry pot device. In order to investigate the erosion process, two series of tests were performed: first one with a constant impact velocity of 5 m/s, 7 m/s and 9 m/s and the second one, during which the impact velocity was changed after every exposure. During each test, an influence of test conditions on volume loss, surface hardness and roughness with exposure time was studied. The normalized erosion rate and erosion efficiency parameter increased linearly with velocity in the range between 5 and 9 m/s. Surface hardness increased exponentially with an exponent n = 0.27. The erosive efficiency parameter determined for tests carried out with variable impact velocity was higher than for tests with constant velocity. The erosion performance increased as the difference in consecutive impact velocity increased. At the beginning of slurry tests, surface hardness and roughness increased rapidly. A fluctuation in erosion rate and surface roughness was noted in the tests performed with variable impact velocity. The amplitudes of these fluctuations decreased with the test duration. Surface hardness influenced damage formed on the specimen’s surface. With increasing surface hardness, surface roughness (Ra parameter) decreased. For surface hardness over 280 HV flakes were formed on the specimen surface.
Source: openaire · Quality: candidate unverified · Source record ↗
Research context
OpenAlex topics: Erosion and Abrasive Machining · High-Temperature Coating Behaviors · Particle Dynamics in Fluid Flows
SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.
References (38)
Show source-provided references
1. Study the effect of impact angle on slurry erosion wear of four different ductile materials
2. An experimental investigation on slurry erosion wear characteristics of brass alloy
3. Erosion wear on centrifugal pump casing due to slurry flow10.1016/j.wear.2016.07.005 ↗
4. Microstructural influence in slurry erosion of ceramics10.1016/0043-1648(95)06679-9 ↗
5. Effect of grain size on the slurry erosive wear of Ce-TZP ceramics10.1016/S1359-6462(00)00415-2 ↗
6. Practical estimation of erosion damage caused by solid particle impact: Part 1: Effects of impact parameters on a predictive equation10.1016/j.wear.2005.01.039 ↗
7. Effect of size and concentration of silt particles on erosion of Pelton turbine buckets10.1016/j.energy.2009.06.015 ↗
8. Practical estimation of erosion damage caused by solid particle impact: Part 2: Mechanical properties of materials directly associated with erosion damage10.1016/j.wear.2005.01.040 ↗
9. Slurry erosion of steel – Review of tests, mechanisms and materials10.1016/j.wear.2018.05.010 ↗
10. Experimental study of particle size, shape and particle flow rate on erosion of stainless steel10.1016/j.powtec.2018.05.039 ↗
11. Erosion of surfaces by solid particles10.1016/0043-1648(60)90055-7 ↗
12. Erosion model on alumina ceramics: A retrospection, validation and refinement10.1016/j.wear.2007.03.002 ↗
13. Prediction of uneven wear in a slurry pipeline on the basis of measurements in a pot tester10.1016/0043-1648(94)06566-7 ↗
14. Slurry erosion performance of Ni-Al2O3 based thermal-sprayed coatings: Effect of angle of impingement10.1007/s11666-013-0013-x ↗
15. Effect of impacting particle kinetic energy on slurry erosion wear10.1007/s40735-015-0028-6 ↗
16. Slurry erosion mechanism of hydroturbine steel: Effect of operating parameters10.1007/s11249-013-0213-z ↗
17. Design and development of high-velocity slurry erosion test rig using CFD10.1007/s11665-012-0219-y ↗
18. Slurry erosion of ductile materials under normal impact condition10.1016/j.wear.2007.03.022 ↗
19. Slurry erosion characteristics and erosion mechanisms of stainless steel10.1016/j.triboint.2014.05.014 ↗
20. The performance of marine coatings and pipe materials under fluid-borne sand erosion10.1016/S0043-1648(98)00231-2 ↗
21. Study of the parametric dependence of erosion wear for the parallel flow of solid-liquid mixtures10.1016/S0301-679X(99)00047-X ↗
22. Development of mechanistic erosion equation for solid particles10.1016/j.wear.2015.01.031 ↗
23. Slurry erosion behaviour of thermomechanically treated 16Cr5Ni stainless steel10.1016/j.triboint.2017.11.025 ↗
24. Effects of surface hardness and other material properties on erosive wear of metals by solid particles10.1115/1.3443422 ↗
25. On ultrahigh velocity micro-particle impact on steels - A multiple impact study10.1016/j.wear.2013.10.011 ↗
26. Effect of erodent properties on the solid particle erosion mechanisms of brittle materials10.1007/s10853-013-7349-y ↗
27. The effect of velocity on the solid particle erosion rate of alloys10.1016/S0043-1648(99)00085-X ↗
28. Development of correlations for predicting the slurry erosion of ductile materials10.1115/1.4004342 ↗
29. Correlation between solid particle erosion of cermets and particle impact dynamics10.1016/j.triboint.2007.09.001 ↗
30. Nominal particle size of multi-sized particulate slurries for evaluation of erosion wear and effect of fine particles10.1016/j.wear.2003.10.013 ↗
31. Slurry erosion – design of test devices10.1515/adms-2017-0007 ↗
32. A re-examination of the ‘particle size effect’ in slurry erosion10.1016/S0043-1648(00)00556-1 ↗
33. Solid particle erosion of AISI 304, 316 and 420 stainless steels10.1016/j.wear.2012.12.047 ↗
34. Wear performance of quenched wear resistant steels in abrasive slurry erosion10.1016/j.wear.2016.02.019 ↗
35. A comprehensive review of solid particle erosion modeling for oil and gas wells and pipelines applications10.1016/j.jngse.2014.10.001 ↗
36. Solid particle erosion mechanisms of protective coatings for aerospace applications10.1016/j.surfcoat.2014.08.037 ↗
37. Erosion efficiency-a new parameter to characterize the dominant erosion micromechanism10.1016/0043-1648(90)90096-S ↗
38. Dislocation theory of yielding and strain ageing of iron10.1088/0370-1298/62/1/308 ↗