Failure analysis of the elements of a forced-in joint operating in rotational bending conditions
Source abstract
Abstract
Abstract Forced-in joints, especially those operating in harsh conditions, are susceptible to premature damage and wear. Such a situation may lead to incidents with severe consequences. Microcracks or changes in the structure of the joint elements may contribute to the development of fatigue cracks and unexpected damage during operation. In this work, typical damage and wear which may be observed at a shaft and sleeve surface made of structural materials used in production of the wheel and axle of the rail vehicle axle set. That damage and wear have come into being as a result of both the pressing process and operation. After the pressing process, the surface of the elements was distinguished by typical traces such as scratches running long the pressing direction, by dents and micropulluots. Brown fretting wear traces at a small distance from the joint edges have been noted at the shaft and sleeve surfaces subjected to fatigue tests through the operation of the rotational bending moment. Fretting wear comprises, to a large extent, material build-ups which have come into being as a result of adhesion-related processes. During operation, those build-ups underwent plastic deformation and oxidation.
Source: openaire · Quality: candidate unverified · Source record ↗
Research context
OpenAlex topics: Mechanical stress and fatigue analysis · Metal Alloys Wear and Properties · Mechanical Failure Analysis and Simulation
SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.
References (30)
Show source-provided references
1. Stress analysis in a bush while assembling a conical interference fit joint
2. Fretting wear behaviors of a railway axle steel10.1016/j.triboint.2009.12.031 ↗
3. Influence of technological methods increasing surface layer durability on axles fretting wear in railway wheel sets10.17531/ein.2016.1.1 ↗
4. The supporting-educational system of constructing the forced-in joint
5. A study on the experimental investigation of low frequency vibration wave assisted disassembly of press-fit joints10.1016/j.jmapro.2019.11.014 ↗
6. L. Boissonnet, B. Duffau, P. Montmitonnet, Tribological study of a press-fit assembling process, ICTMP 2010, Jun 2010, Nice, France. 10 p. hal-00527847.
7. Failure mechanism analysis on railway wheel shaft of power locomotive10.1016/j.engfailanal.2019.05.013 ↗
8. Modeling on bearing behavior and damage evolution of single-lap bolted composite interference-fit joints10.1016/j.compstruct.2019.01.044 ↗
9. Stress distribution modeling for interference-fit area of each individual layer around composite laminates joint10.1016/j.compositesb.2015.04.013 ↗
10. Analysis of elastic-plastic interference-fit joints10.1016/j.proeng.2014.10.276 ↗
11. The carrying capacity of conical interference-fit joints with laser reinforcement zones10.1016/j.jmatprotec.2010.02.004 ↗
12. Wear margin of ship machine units with press fits
13. Parameters affecting the damage tolerance behaviour of railway axles10.1016/j.engfracmech.2010.03.013 ↗
14. The influence of bone damage on press-fit mechanics10.1016/j.jbiomech.2014.01.029 ↗
15. K. Karwala, H. Kulikowski, A. Tułecki, Technological problems of wheelset durability in terms of adaptation of rail vehicles to increased speeds. PhD thesis, 1991.
16. Experimental investigation of fretting wear of coated spring clip and inlet ring in land-based gas turbines at elevated temperature
17. Torsional fretting fatigue strength of a shrink-fitted shaft with a grooved hub10.1016/S0301-679X(00)00102-X ↗
18. Effect of hardness differential on metal-to-metal fretting damage10.1016/j.wear.2013.01.003 ↗
19. Effects of thickness and cycle parameters on fretting wear behavior of CVD diamond coatings on steel substrates10.1016/j.surfcoat.2010.06.026 ↗
20. Fretting wear of stainless steels under variable temperature conditions: Introduction of a ‘composite’ wear law10.1016/j.wear.2009.08.029 ↗
21. Influence of humidity on the endurance of silver-plated electrical contacts subjected to fretting wear10.1016/j.surfcoat.2018.07.109 ↗
22. Fretting behavior of the AISI 304 stainless steel under different atmosphere environments10.1016/j.triboint.2015.02.016 ↗
23. Waterhouse · 1972
24. Fretting wear-induced evolution of surface damage in press-fitted shaft10.1016/j.wear.2017.05.014 ↗
25. Effect of plastic deformation and fretting wear on the fretting fatigue of scaled railway axles10.1016/j.ijfatigue.2019.105371 ↗
26. Fretting wear simulation in a clamped joint based on the example of a rail vehicle wheelset
27. The effect of gross sliding fretting wear on stress distributions in thin W-DLC coating systems10.1016/j.triboint.2010.01.018 ↗
28. Kyungmok Kim, Alexander M. Korsunsky, Dissipated energy and fretting damage in CoCrAlY-MoS2 coatings, Tribol. Int. 43 (2010) 676–684.10.1016/j.triboint.2009.10.007 ↗
29. Fretting wear behavior of duplex PEO/chameleon coating on Al alloy10.1016/j.surfcoat.2018.07.100 ↗
30. Fretting wear and fretting fatigue behaviors of diamond-like carbon and graphite-like carbon films deposited on Ti-6Al-4V alloy10.1016/j.apsusc.2014.06.006 ↗