Experimental and numerical study on the longitudinal-crack failure of double-shoulder tool joint
Source abstract
Abstract
Abstract In recent years, the failure accidents of double-shoulder tool joint caused by longitudinal-crack occur frequently during drilling with increasing deep and ultra-deep wells, directional wells, extended reach wells and horizontal wells, which not only decreases rate of penetration, but also results in huge economic losses. Although the frictional heat check cracking can cause cracking initiation according to the standard API RP 7G, it has been found heat check cracking is just one of the cracking initiation mechanism rather than crack propagation mechanism; in other words, there are various other causes of crack initiation and propagation. Hence, in order to find out the failure mechanism caused by longitudinal-crack, the failure analysis of one typical double-shoulder joint with longitudinal crack has been investigated in detail from three aspects including its service load, its own structure feature and fracture toughness by combining experimental inspection and finite element simulation. The results from macro-analysis, micro-analysis, chemical component analysis, mechanical properties analysis, stress and deformation analysis, show that this failure mechanism of double-shoulder joint is closely and directly related to overlarge combined load (tensile force, torsion and bending), its own structure feature and difference of fracture toughness between transverse section and longitudinal section. Firstly, the martensite is produced on the thread surface due to severe fraction heat between threads caused by overlarge combined load during jarring releasing of double-shoulder joint, which leads to the inter-granular crack initiation. Secondly, the circumferential stress release is restricted by thread connection. Thirdly, the transverse fracture toughness of material is lower than longitudinal fracture toughness. Finally, the longitudinal-crack failure of this double-shoulder joint occurs under overlarge alternating combined load. It is suggested that if the thread taper of double-shoulder joint is decreased and the area of secondary shoulder is increased under extreme working environment, the bearing capacity of connection can be improved and the failure accident caused by longitudinal-crack can be avoided effectively.
Source: openaire · Quality: candidate unverified · Source record ↗
Research context
OpenAlex topics: Fatigue and fracture mechanics · Hydrogen embrittlement and corrosion behaviors in metals · Metal Alloys Wear and Properties
SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.
References (18)
Show source-provided references
1. Helin · 1999
2. API RP 7G[S] · 1998
3. Failure analysis of Φ127mm IEU G105 drill pipe wash out10.1016/j.engfailanal.2011.06.018 ↗
4. Failure analysis of drill pipe: a review10.1016/j.engfailanal.2015.10.012 ↗
5. Longitudinal crack failure analysis of box of S135 tool joint in ultra-deep well10.1016/j.engfailanal.2014.11.022 ↗
6. A study on axial cracking failure of drill pipe body10.1016/j.engfailanal.2015.11.004 ↗
7. Fatigue crack growth analysis of drill pipes during rotary drilling operations by the multiple reference state weight function approach10.1016/j.engfailanal.2016.12.013 ↗
8. A comprehensive analysis on the longitudinal fracture in the tool joints of drill pipes10.1016/j.engfailanal.2017.03.019 ↗
9. Failure analysis and appropriate design of drill pipe upset transition area10.1016/j.engfailanal.2013.02.006 ↗
10. API Spec 5DP, Specification for Drill Pipe.
11. Contact stress analysis and calculation of stress concentration factors at the tool joint of a drill pipe
12. Michacl · 2007
13. 3D dynamic simulation of groove and ridge in two-body abrasive wear by finite element method
14. Failure analysis and solution studies on drill pipe thread gluing at the exit side of horizontal directional drilling10.1016/j.engfailanal.2013.05.017 ↗
15. Betten · 2008 · 256
16. Honghuo · 2007
17. Failure analysis and solution studies on drill pipe thread gluing at the exit side of horizontal directional drilling10.1016/j.engfailanal.2013.05.017 ↗
18. Controlled residual stresses introduction to improve fatigue resistance of rotary shouldered connections used in oil drilling industry10.1016/j.ijpvp.2010.10.005 ↗