journal article·2026-02Open access

Microstructural evaluation and failure analysis of flow forming mandrels: Case studies

Qianxi He, Goulnara K. Dosbaeva

Abstract

• Metallography reveals defects and structural flaws in cold flow forming mandrels. • Subsurface cracks in failed mandrels identified by SEM, XRD, and stress analysis. • Proper EDM reduces white layer formation and surface tensile stress in mandrels. • Inter-critical annealing improves fracture toughness of DC53 tool steel. This study presents comprehensive metallographic observations on defects and other structural insufficiencies, such as micro-crack development and their causes during cold flow forming of different steel parts. Flow forming is an ideal process for manufacturing parts made of high-strength materials. The process’s high forming forces can produce these parts within tight dimensional and thickness tolerances. This requires the highest standards in surface consistency of hardened flow forming tools to perform serial production of parts (within the range of thousands). This paper shows the importance of structural insufficiencies, particularly under surface area and their role in the failure of flow forming tooling. Tool life is presented for different mandrels made of DC53 cold work steel. All of them were used in the flow forming process. Failure case studies were based on the failed versus well-performing mandrel taken from the production line. SEM, XRD analyses, metallographic studies and residual stresses evaluation were performed. Importance of properly performed EDM to minimize the white (re-cast) layer formation and surface stress is outlined. The present work also points out the role of inter-critical annealing on the fracture toughness of steel DC53.
Source: openalex_inverted_index · Quality: baseline

Research context

OpenAlex topics: Metal Forming Simulation Techniques · Metallurgy and Material Forming · Microstructure and Mechanical Properties of Steels

SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.

References (38)

Show source-provided references
1. An investigation of the development of defects during flow forming of high strength thin wall steel tubes10.1007/BF02715366 ↗
2. Fatigue analysis of cold pilger mill mandrel for tube drawing using Cad/Cae software
3. Spinning of tubes: a review10.1007/BF02834039 ↗
4. Real-time defects detection in flow-forming process10.1016/0924-0136(92)90193-V ↗
5. D. Marini, D. Cunningham, J. Corney, A review of flow forming processes and mechanisms, in: Mater. Form. ESAFORM 2015, Trans Tech Publications Ltd, 2015: pp. 750–758. https://doi.org/10.4028/www.scientific.net/KEM.651-653.750.10.4028/www.scientific.net/KEM.651-653.750 ↗
6. Change of microstructure and mechanical property in the failure process of H13 mandrel
7. Barlow · 2010
8. Geller · 1978
9. Failure and heat treatment of pilger mandrels made from X38CrMoV51 steel10.1016/S1350-6307(01)00037-1 ↗
10. Moiseev · 1998
11. INTERNATIONAL STANDARD, ISO 6508-1:2015 Rockwellhardness test, 2015 (2015) 1–20.
12. The role of the distance between fine non-metallic oxide inclusions on the fatigue strength of low-carbon steel10.3390/app13148354 ↗
13. A numerical study on the effects of DP steel microstructure on the yield locus and the stress–strain response under strain path change10.1007/s12289-022-01731-2 ↗
14. Study of the influence of carbide inhomogeneity on operational and technological properties of high-speed tool steels10.1088/1757-899X/986/1/012007 ↗
15. L.H. Chiu, H.C. Liao, S.C. Lin, Y.T. Pan, H.Y. Liou, Carbide distribution effect on wear behavior of cold work tool steels, in: Metall. Technol. Mater., Trans Tech Publications Ltd, 2012: pp. 240–243. https://doi.org/10.4028/www.scientific.net/AMR.567.240.10.4028/www.scientific.net/AMR.567.240 ↗
16. Electro-discharge machining (EDM) versus hard turning and grinding—comparison of residual stresses and surface integrity generated in AISI O1 tool steel10.1016/j.jmatprotec.2007.04.131 ↗
17. R. Sen, P. Charkraborti, J. Debbarma, Wear behavior in wire of wire cut EDM, in: Mech. Control Eng. III, Trans Tech Publications Ltd, 2015: pp. 70–76. https://doi.org/10.4028/www.scientific.net/AMM.704.70.10.4028/www.scientific.net/AMM.704.70 ↗
18. Becker · 2002
19. Influence of shallow and deep cryogenic treatment on the residual state of stress of 4140 steel10.1016/j.jmatprotec.2010.10.018 ↗
20. Quantitative assessment of stress redistribution effect at the crack tip after unloading under compression10.1016/j.engfracmech.2025.111441 ↗
21. Investigation on tool wear mechanisms and machining tribology of hardened DC53 steel through modified CBN tooling geometry in hard turning10.1007/s00170-023-11528-5 ↗
22. Three-dimensional wear parameters and wear mechanisms in turning hardened steels with PCBN tools10.1016/j.wear.2017.11.017 ↗
23. On the use of Charpy transition temperature as reference temperature for the choice of a pipe steel10.1016/j.engfailanal.2013.11.001 ↗
24. Effect of intercritical annealing parameters and starting microstructure on the microstructural evolution and mechanical properties of a medium-Mn third generation advanced high strength steel10.3390/met12020356 ↗
25. Effect of intercritical annealing on the microstructure and mechanical properties of 0.1C-13Cr-3Ni Martensitic stainless steel10.3390/met11030392 ↗
26. Interpretation of Charpy impact energy characteristics by microstructural evolution of dynamically compressed specimens in three tempered martensitic steels10.1016/j.msea.2015.09.099 ↗
27. The effect of the intercritical annealing process on the microstructure evolution, strength, and toughness of cryogenic 5.5Ni steel10.1016/j.matchar.2025.115005 ↗
28. Effect of intercritical annealing on the mechanical properties of dual-phase steel10.1080/03019233.2022.2062163 ↗
29. Experimental analysis of the ductile-to-brittle transition in high-strength thin metal sheets: charpy and novel impact tensile tests10.1007/s11340-025-01227-5 ↗
30. Influence of carbide and inclusion contents on the fatigue properties of high speed steels and tool steels10.1016/S0142-1123(00)00087-6 ↗
31. Microstructural characterisation of brittle fracture initiation sites in reactor pressure vessel steels
32. Influence of carbide morphology on the deformation and fracture mechanisms of spheroidized 14CrMoR steel10.3390/met9111221 ↗
33. Magnetic evaluation of creep in modified 9Cr–1Mo steel10.1016/j.scriptamat.2007.07.004 ↗
34. Effect of post-heat treatment on residual stress and tensile strength of hybrid additive and subtractive manufacturing10.1007/s00170-019-03705-2 ↗
35. Void-induced ductile fracture of metals: experimental observations10.3390/ma15186473 ↗
36. Fracture appearance and mechanisms of deformation and fracture10.31399/asm.hb.v11.a0006774 ↗
37. Characteristics and mechanisms of hydrogen-induced quasi-cleavage fracture of lath martensitic steel10.1016/j.actamat.2021.116635 ↗
38. Microstructure, mechanical properties, and wear behavior of an improved rock-breaking cutter ring steel used on tunnel boring machine10.1007/s11665-025-11271-w ↗