journal article·2023-10Open access

Effect of chemical composition on hot cracking susceptibility (HCS) using various hot cracking criteria

E. Pujiyulianto, Suyitno, K. Rajagukguk, B. Arifvianto, L. Katgerman, F. Paundra, H.T. Yudistira, F.P. Nurullah, A. Muhyi, M.F. Arif

Abstract

The paper aims to evaluate the effect of chemical composition on the Hot Cracking Susceptibility (HCS) using mechanical and non-mechanical hot cracking criteria during solidification. The criteria were SKK as a mechanical criterion. Feurer, Clyne Davis, and Katgerman as non-mechanical criteria. The criteria were implemented at various parameters to evaluate their abilities in the hot cracking susceptibility (HCS) prediction at varied chemical composition. In this study, The Mg content was varied in Al9Zn (1, 1.5, 2, 2.5 %wt.) Mg2Cu alloys and Cu content in Al9Zn2Mg (1, 1.5, 2, 2.5 %wt.) Cu alloys. The validation of the result is also conducted by comparing with the experimental data. Based on Feurer criterion, The hot cracking initiates at lower temperature and at higher critical rate of feeding and shrinkage with Cu content, and the hot cracking initiates at higher temperature with Mg content, and it initiates at higher critical rate of feeding and shrinkage from 1 up to 1.5 of Mg, and the critical rate of feeding and shrinkage remains constant from 1.5 up to 2.5 of Mg. Based on Clyne & Davies, the HCS decreases with Cu content from 1 up to 2 of Cu, and it increases from 2 up to 2.5 of Cu. The HCS decreases with Mg content from 1 up to 2 of Mg, and it remains constant from 2 up to 2.5 of Mg. Based on Katgerman criterion, the HCS decreases with Cu content from 1 up to 1.5 of Cu, it increases from 1.5 up to 2 of Cu, and it decreases from 2 up to 2.5 of Cu. The HCS decreases sequentially with Mg content. Based on SKK criterion, the HCS curves shift to the right with Cu content which means that the hot cracking initiates at lower temperature, and the HCS curves shift to the left with Mg content which means that the hot cracking initiates at higher temperature with Mg content. The Feurer, Clyne & Davies, and some specific range for SKK criteria are in agreement for the effect of Cu content on HCS of alloys, and Katgerman and some specific range for Clyne&Davies criteria are in agreement for the effect of Mg content on HCS of alloys.
Source: openaire · Quality: candidate unverified · Source record ↗

Research context

OpenAlex topics: Aluminum Alloy Microstructure Properties · Aluminum Alloys Composites Properties · Metallurgy and Material Forming

SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.

References (47)

Show source-provided references
1. Campbell · 1991
2. Hot tearing of aluminum alloys: a critical literature review
3. Suyitno · 2005
4. Complete Casting Handbook: Metal Casting Process, Metallurgy, Techniques and Design
5. Multiphase-field simulation of grain coalescence behavior and its effects on solidification cracking susceptibility during welding of Al-Cu alloys10.1016/j.matdes.2021.110146 ↗
6. Hattingh “Weld solidification cracking in a 304L stainless steel water tank”
7. Z. Gao, Y. Yang, L. Wang, B. Zhou, F. Yan, Formation mechanism and control of solidification cracking in laser-welded joints of steel/copper dissimilar metals, Metal, 12, 1147, 2022.10.3390/met12071147 ↗
8. C. Xia, S. Kou, Evaluating susceptibility of Ni-base alloys to solidification cracking by transverse-motion weldability test, Sci. Technol. Welding Join. 15(8) (2020) 1-8.10.1080/13621718.2020.1802897 ↗
9. Calculating the susceptibility of carbon steels to solidification cracking during welding10.1007/s11663-020-02021-5 ↗
10. Recent advances in hot tearing during casting of aluminum alloys10.1016/j.pmatsci.2020.100741 ↗
11. I.I. Novikov, Goryachelomkost tsvetnykh metallovi splavov (hot shortness of non-ferrous metals and alloys) 299, 1966.
12. Mechanical properties of solidifying shell of aluminum alloys
13. Physical modeling of the deformation mechanisms of semisolid bodies and a mechanical criterion for hot tearing10.1007/s11663-001-0124-5 ↗
14. J. Langlais, J.E. Gruzleski, A novel approach to assessing the hot tearing susceptibility of aluminum alloy, Mater. Sci. Forum 1 (2000) (2331-2337),167-172.10.4028/www.scientific.net/MSF.331-337.167 ↗
15. Deformation, strength, and fracture above the solidus temperature
16. Hot tearing criteria evaluation for direct-chill casting of an al-4.5 pct Cu alloy10.1007/s11661-005-0245-6 ↗
17. W.H. Kool Suyitno, L. Katgerman, Evaluation of mechanical and non-mechanical hot tearing criteria for dc casting of an aluminum alloy, Light Metals, 753-758, 2003.
18. L.Y. Zhao, Baoyin, N. Wang, V. Sahjwalla, R.D. Pehlke, The rheological properties and hot tearing behavior of an Al-Cu alloy, Int. J. Cast Met. Res. 13(3) (2000) 167-174.10.1080/13640461.2000.11819399 ↗
19. Mechanical properties in the semi-solid sate and hot tearing of aluminum alloys10.1016/S0079-6425(03)00037-9 ↗
20. resistance to hot tearing of cast metals during solidification
21. A new hot tearing criterion10.1007/s11661-999-0334-z ↗
22. M. Braccini, C.L. Martin, M. Suéry, Y. Bréchet, modeling of casting Welding and Advanced Solidification Processes IX, 18-24, 2000.
23. M. M’Hamdi, A. Mo, H.G. Fjær, TearSim, A two-phase model addressing hot tearing formation during aluminum direct chill casting, Metall. Mater. Trans. A, 37 (2006) 3069–3083.10.1007/s11661-006-0188-6 ↗
24. Development of thermal strain in the coherent mushy zone during solidification of aluminum alloys10.1007/s11661-004-0238-x ↗
25. T. W. Clyne, G.J. Davies, Solidification and casting of metals, The Metals Society (1979) 275-278.
26. A mathematical model for hot cracking of aluminum alloys during dc casting
27. Integrated approach for prediction of hot tearing10.1007/s11661-009-9941-y ↗
28. A modified hot tearing criterion for direct chill casting of aluminum alloys
29. Observation and prediction of the hot tear susceptibility of ternary Al-Si-Mg alloys10.1007/s11661-012-1132-6 ↗
30. L. Sweet, J. Taylor, M. Easton, M. Couper, N. Parson, Chemical additions to reduce hot tearing in the cast house. Light Metals: Springer International Publishing (2012) 1133–1138.10.1002/9781118359259.ch195 ↗
31. A.A. Griffith, The theory of rupture, In: Proc., Ist., Int., Congr., Appl., Mech. Biereno, C.B. Burgers, J.M(eds). Delft: Tech. Boekhandel en Drukkerij. J. Waltman Jr, 54-63.
32. The phenomena of rupture and flow in solids10.1098/rsta.1921.0006 ↗
33. U. Feurer, Quality Control of Engineering Alloys and the Role of Metals Science, Delft University of Technology, Delft, 1997, 131.
34. Effect of main elements (Zn, Mg, and Cu) on hot tearing susceptibility during direct-chill casting of 7xxx aluminum alloys10.1007/s11661-019-05268-z ↗
35. Effect of Cu on the hot tearing susceptibility of Al–6Zn–2.5Mg–xCu alloy10.1007/s40962-020-00438-x ↗
36. Kurz · 1992
37. 1970
38. Evaluation of quantitative hot cracking criteria10.1080/02670836.2022.2040129 ↗
39. A quest for a new hot tearing criterion10.1007/s11661-007-9169-7 ↗
40. Nonmechanical criteria proposed for prediction of hot tearing sensitivity in 2024 aluminum alloy10.1016/S1003-6326(18)64718-1 ↗
41. effect of cooling rate on the dendrite coherency point during solidification of Al2024 alloy10.1007/s11661-014-2697-z ↗
42. Investigation on the effect of cooling rate on hot tearing susceptibility of Al2024 alloy using thermal analysis10.1007/s11663-015-0450-7 ↗
43. L. Fa-Guo, D. Qing, Z. Jiao, D. Yong-Bing, F. Ya-Nan, X. Hong-Lan, Y. Fu-Cheng, S. Bao-De, in situ on columnar-equiaxed transition and an axial columnar dendrite growth of Al−15%Cu alloy by synchrotron radiography, Trans. Nonferrous Met. Soc. China, 24 (2014) 2112−2116.10.1016/S1003-6326(14)63320-3 ↗
44. Development of a new hot-cracking test for aluminium alloys
45. Oppong “Crack formation of camshaft castings: hot tearing susceptibility and root causes”10.1016/j.engfailanal.2023.107143 ↗
46. A. Almomani, A. Hamid I. Mourad, I. Barsoum, Effect of sulfur, phosphorus, silicon, and delta ferrite on weld solidification cracking of AISI 310S austenitic stainless steel, Eng. Fail. Anal. 139 (2022) 106488.10.1016/j.engfailanal.2022.106488 ↗
47. M.N. James, L. Matthews, D.G. Hattingh, Weld solidification cracking in a 304L stainless steel water tank, Eng. Fail. Anal. 115 (2020) 104614.10.1016/j.engfailanal.2020.104614 ↗