Bucket wheel excavator: Integrity assessment of the bucket wheel boom tie-rod welded joint
Source abstract
Abstract
Abstract The bucket wheel boom tie-rods are vital structural parts of the bucket wheel excavators (BWE). Their failures inevitably cause BWE collapse and are followed, among other things, by a substantial financial loss (millions of €). Non-destructive testing revealed a flaw in the butt welded joint of the body and eye-plate of the bucket wheel tie-rod. Its size exceeds the level allowed by current technical regulations. An integrity assessment of the bucket wheel tie-rod has been carried out, i.e. the remaining fatigue life has been determined based on the stress-state characteristics in the welded joint and defined by experimental research in real working conditions. The calculation results show that despite the excessive size of the internal flaw the welded joint integrity is not compromised. During periodical inspections of the welded joint in the past two years (BWE was put into operation in December 2007) changes that could compromise the structural integrity were not observed. In this way, by using a “fail-safe” philosophy design, a considerable financial saving (ca. 1,600,000 €) was achieved while at the same time there was no threat to the worker’s safety and life, the safety of the machine and the production process in the open pit mine.
Source: openaire · Quality: candidate unverified · Source record ↗
Research context
OpenAlex topics: Mechanical Engineering Research and Applications · Mechanical Failure Analysis and Simulation · Industrial Engineering and Technologies
SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.
References (30)
Show source-provided references
1. Failure analysis of the end eye connection of the bucket wheel excavator portal tie-rod support10.1016/j.engfailanal.2008.06.006 ↗
2. An analysis of the causes of a BWE counterweight boom support fracture10.1016/j.engfailanal.2009.06.001 ↗
3. Araujo LS, de Almeida LH, Batista EM. Analysis of a bucketwheel stacker reclaimer structural failure. In: Proceedings of the conference “materials science & technology 2009”, Charles R. morin memorial symposium on failure analysis and prevention: 2009. Pitsburgh: proceedings on CD.
4. Failure analysis of stacker–cum reclaimer in ore handling plant10.1007/s11668-008-9183-0 ↗
5. Bošnjak S, Stojanović D. Expertise of failure of the mechanized open storage of coal in the thermal power plant TENT B. University of Belgrade, Faculty of Mechanical Engineering. Report No. 267/05, Belgrade; 2005 [in Serbian].
6. Structural failure of a telescopic shiploader during installation10.1007/s11668-007-9049-x ↗
7. Technical failure investigation of welded structures (or how to get the most out of failures)10.1016/j.engfailanal.2005.01.005 ↗
8. Failure of components and products by ‘engineered-in’ defects: case studies10.1016/j.engfailanal.2004.12.008 ↗
9. Methodologies for failure analysis: a critical survey10.1016/j.matdes.2003.09.020 ↗
10. Pantelić M. Maintenance conception improvement via operational safety management of excavator units at coal mines. PhD dissertation, University of Kragujevac, Technical Faculty in Čačak; Čačak; 2009 [in Serbian].
11. Construction of diagnostic models of the states of developing fault for working parts of the multi-bucket excavator
12. In-service fatigue failure of engineered products and structures – case study review10.1016/j.engfailanal.2008.08.008 ↗
13. Fatigue life prediction of heavy mining equipment. Part 1: fatigue load assessment and crack growth rate tests10.1016/j.jcsr.2007.01.008 ↗
14. Fatigue life prediction of heavy mining equipment. Part 2: behaviour of corner crack in steel welded box section and remaining fatigue life determination10.1016/j.jcsr.2007.04.003 ↗
15. New approaches in heavy duties industrial processes monitoring by using smart sensors
16. Bartelmus · 2006
17. A new feature for monitoring the condition of gearboxes in non-stationary operating conditions10.1016/j.ymssp.2009.01.014 ↗
18. ISO 4063. Welding brazing, soldering and braze welding of metals – nomenclature of processes and reference numbers for symbolic representation on drawings. INTERNATIONAL ORGANIZATION FOR STANDARDIZATION; 1990.
19. EN 10002-1. Metallic materials – tensile testing – part 1: method of test (at ambient temperature). EUROPEAN COMMITTEE FOR STANDARDIZACION; 1990.
20. EN ISO 5817. Welding–fusion–welded joints in steel, nickel, titanium and their alloys (beam welding excluded) – quality levels for imperfection. EUROPEAN COMMITTEE FOR STANDARDIZACION; 2007.
21. EN 1714./prA. Non destructive examination of welds – ultrasonic examination of welded joints. EUROPEAN COMMITTEE STANDARDIZACION; 1997/2001.
22. Mathematical modeling of dynamic processes of bucket wheel excavators
23. On the dynamic modeling of bucket wheel excavators
24. Bošnjak S, Zrnić N, Petković Z. Bucket wheel excavators and trenchers – computer aided calculations of loads caused by resistance-to-excavation. In: Machine design (monograph). Novi Sad: Faculty of technical sciences; 2008. p. 121–8.
25. Comparative analysis of strength for variant structural solutions of lower structure for bucket wheel excavator KRUPP C-700S
26. Cracks, repair and reconstruction of bucket wheel excavator slewing platform10.1016/j.engfailanal.2008.11.009 ↗
27. ASTM E 647. Standard test method for measurement of fatigue crack growth rates. ASTM standard; 2000.
28. Vasil’chenko · 1979
29. Hertzberg · 1995
30. Methods for external validation of continuous system simulation model10.1080/13873959808837066 ↗