journal article·2026-06Open access

Trajectory-dependent melt dynamics and microstructure evolution in laser wire additive manufacturing of 6063 aluminum alloy

Zhuoqi Cai, Yun Zhao, Chengwei Yuan, Mengxue Wang, Jiacheng Wang, Jun Xiao, Fan Jiang

Abstract

In laser wire-feed additive manufacturing of 6063 aluminum alloy, highly concentrated heat input and steep thermal gradients easily cause molten pool instability, irregular droplet transfer, and uneven energy distribution. This study systematically explores how oscillation trajectories regulate droplet transfer stability, molten pool dynamics, bead geometry, and microstructural evolution during de position. Under the same processing parameters, four typical oscillation patterns (“|”, “8”, “∞“, “○“) were compared. Energy distribution was analyzed via trajectory functions, droplet transfer and melt flow were observed by high-speed imaging, surface morphology was examined by laser confocal microscopy, and microstructure and crystallographic texture were characterized by optical microscopy and electron backscatter diffraction (EBSD). Results show oscillation trajectories significantly affect energy redistribution and melt convection, thus modulating droplet dynamics and solidification. The “|” trajectory had limited lateral stirring and periodic flow interruptions, causing rough surfaces and coarse grains. The “8” trajectory enhanced central energy and penetration but induced local flow instability at intersections. The “∞” trajectory formed continuous symmetric dual-loop flow, achieving uniform melt flow, the largest width-to-height ratio, refined grains (with a maximum grain size reduction of 18.63% compared to the “8” trajectory), and the weakest texture. The “○” trajectory ensured good surface smoothness and little spatter but slight cross-sectional asymmetry. In conclusion, the “∞” trajectory optimally balances geometry control and microstructure refinement.
Source: openalex_inverted_index · Quality: baseline

Research context

OpenAlex topics: Additive Manufacturing Materials and Processes · High Entropy Alloys Studies · Additive Manufacturing and 3D Printing Technologies

SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.

References (25)

Show source-provided references
1. A review of Laser Additive Manufacturing (LAM) aluminum alloys: methods, microstructures and mechanical properties10.1016/j.optlastec.2024.110722 ↗
2. Eutectic aluminum alloys fabricated by additive manufacturing: a comprehensive review10.1016/j.jmst.2025.06.016 ↗
3. Multiscale defect engineering for synergistic strength, electrical and thermal conductivity in aluminum alloys: a review10.1016/j.jmrt.2025.12.113 ↗
4. Influence of Follow-up wire feeding strategy on aluminum alloy Laser Wire additive manufacturing forming10.1016/j.optlastec.2025.113457 ↗
5. Review of the laser powder bed fusion of nitinol: defect Formation and prediction
6. Heat transfer and flow of molten pool in single track multi-layer aluminum alloy Laser Wire additive manufacturing10.1016/j.optlastec.2024.111858 ↗
7. Droplet transfer characteristics in high-power Laser–MAG hybrid welding: influenceof energy parameters10.1016/j.optlastec.2024.111496 ↗
8. Inter-Wire Current driven molten pool flow in oscillating-laser quad-wire deposition process10.1016/j.jmapro.2025.05.031 ↗
9. Effect of welding speed on microstructure and properties of laser-welded S31254 super austenitic stainless steel ultra-thin sheets10.1016/j.jmrt.2025.12.109 ↗
10. Microstructure evolutionand property improvement of nickel-based Alloy/Duplex stainless steel welded joints with oscillating laser offset10.1016/j.jmrt.2025.08.030 ↗
11. Experimental and numerical analysis of molten pool dynamics in adjustable ring-mode laser welding of TC4 titanium alloys10.1016/j.ijthermalsci.2025.110548 ↗
12. Effect of heat input on microstructure and impact toughness of X80 FCAW-S weld joint10.1016/j.jmrt.2026.01.052 ↗
13. Wear behaviors of laser-directed energy deposited inconel 625 alloys-based composite coating by different oscillating laser paths10.1016/j.optlastec.2025.113900 ↗
14. Enhanced surface finish and reduced porosity of TiC nanoparticles reinforced 2219 aluminum alloy deposit fabricated via oscillating Laser-Arc hybrid additive manufacturing10.1016/j.jmapro.2024.04.071 ↗
15. Synergistic enhancement of weld stability and mechanical performance in laser welding of titanium alloy by coupling ring-shaped mode and beam oscillation10.1016/j.jmatprotec.2025.119053 ↗
16. Laser beam oscillation strategy for Weld geometry variation10.1016/j.jmapro.2022.10.016 ↗
17. Microstructural characteristics and mechanical properties of Al-Cu alloys fabricated via 8-Shaped oscillating Laser Wire additive manufacturing10.1016/j.msea.2024.147101 ↗
18. Determination of beam oscillating pattern for tailoring melt flow and microstructural characteristics of laser WeldedTi–6Al–4V alloy10.1016/j.ijthermalsci.2024.109156 ↗
19. Numerical and experimental investigation of heat transfer and flow in oscillating laser dual-wire deposition10.1016/j.ijthermalsci.2025.109741 ↗
20. Characteristic of Keyhole,Molten pool and microstructure of oscillating laser TIG hybrid welding10.1016/j.optlastec.2023.109142 ↗
21. Laser beam oscillation welding of Ta-10W refractory alloy: molten pool, keyhole behavior and porosity10.1016/j.ijrmhm.2025.107550 ↗
22. Research on hole inhibiting mechanism of 5A06 aluminum alloy during laser oscillating FuseDeposition forming10.1016/j.optlastec.2023.109530 ↗
23. Formation and migration of bubbles under different laser oscillation paths during laser welding process of medium-thick Al alloy10.1016/j.ijheatmasstransfer.2024.126553 ↗
24. Effect of oscillation parameters on adjustable-ring mode (ARM) laser beam welding of aluminum alloys10.1016/j.jmapro.2024.01.060 ↗
25. Microstructure evolution and porosity suppression in high-power Laser-Arc hybrid welded thick aluminum alloy T-Joints through high-frequency beam oscillation10.1016/j.jmrt.2025.04.198 ↗