Enhanced microstructure, mechanical properties, and thermal stability of powder metallurgy Al-Ni-Cu-Fe alloy through thermomechanical processing and recrystallization
Source abstract
Abstract
Powder metallurgy (PM) Al-Ni-Cu-Fe alloys are promising for use as lightweight, heat-resistant structural components in automotive and industrial applications. However, their practical use is limited by interfacial inhomogeneities and second-phase segregation. To address these challenges, this study implemented a novel three-stage post-sintering processing route comprising T4 solution pre-treatment, thermomechanical processing through hot rolling, and T6 aging. The T4 pretreatment promoted grain coarsening and reduced elemental segregation, thus improving alloy workability. Thermomechanical processing through hot rolling facilitated dynamic recrystallization, resulting in a uniform dispersion of secondary phases. The subsequent T6 aging refined the grains to an equiaxed structure and reduced the rolling-induced texture. As a result, the alloy achieved a tensile strength above 280 MPa, ∼7 % ductility, and maintained remarkable thermal stability below 200 °C. The strengthening was primarily attributed to grain-boundary pinning and hard-phase contributions from Al 9 FeNi and Al 3 (Zr, Sc), along with nano-precipitated Al 2 Cu and thermally stable quasi-periodic phases. These quasi-periodic phases formed semi-coherent interfaces with Al 9 FeNi and the matrix, serving as stress buffers to stabilize grain boundaries and enhance overall thermal stability. Together, these synergistic effects highlight the alloy's potential for high-temperature structural applications and provide insights to advance the development of heat-resistant PM aluminum alloys.
Source: openalex_inverted_index · Quality: baseline
Research context
OpenAlex topics: Aluminum Alloy Microstructure Properties · Aluminum Alloys Composites Properties · Microstructure and mechanical properties
SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.
References (56)
Show source-provided references
1. Advantages and effectiveness of the powder metallurgy in manufacturing technologies
2. Development and applications of aluminum alloys for aerospace industry10.1016/j.jmrt.2023.09.274 ↗
3. Recent developments in powder metallurgy based aluminum alloy composite for aerospace applications10.1016/j.matpr.2019.07.568 ↗
4. Strengthening retention and structural stability of the Al-Al3Ni eutectic at high temperatures10.1016/j.scriptamat.2022.114679 ↗
5. Ambient-and elevated temperature properties of Sc-and Zr-modified Al–6Ni alloys strengthened by Al3Ni microfibers and Al3(Sc, Zr) nanoprecipitates10.1016/j.msea.2022.142963 ↗
6. Effects of pre-and post-friction surfacing heat treatment on microstructure and corrosion behavior of nickel-aluminide reinforced Al-Cu-Mg alloy10.1016/j.jallcom.2022.164211 ↗
7. Anomalous kinetics, patterns formation in recalescence, and final microstructure of rapidly solidified Al-rich Al-Ni alloys10.1016/j.actamat.2022.118384 ↗
8. Effects of Ni on the microstructure, hot tear and mechanical properties of Al–Zn–Mg–Cu alloys under as-cast condition10.1016/j.jallcom.2019.153458 ↗
9. A novel method for improving the microstructure and the properties of Al-Si-Cu alloys prepared using rapid solidification/powder metallurgy
10. Structural characterization of unique core-shell shaped Al3Ni2/Al3Ni in-situ intermetallic in Al–4Cu-xNi via powder metallurgy (P/M)
11. Effects of silicon on the metallurgy and sintering response of Al–Ni–Mg PM alloys10.1016/j.msea.2006.11.038 ↗
12. Precipitation behavior in an Al–Cu–Mg–Si alloy during aging10.1016/j.msea.2019.138369 ↗
13. Precipitation phenomena and strengthening mechanism of Al–Cu alloys deposited by in-situ rolled wire-arc additive manufacturing10.1016/j.msea.2022.143770 ↗
14. Structure and mechanical behavior of ultrafine-grained aluminum-iron alloy stabilized by nanoscaled intermetallic particles10.1016/j.actamat.2019.01.027 ↗
15. Towards high mechanical performance Al–Cu–Mg–Fe–Ni alloy: influence of composition, solution treatment and aged process on microstructural evolution and mechanical properties10.1016/j.jmrt.2023.01.166 ↗
16. Thermal stability of Al–Fe–Ni alloy at high temperatures10.1016/j.jmrt.2019.01.028 ↗
17. Effects of the microstructure and texture characteristics on mechanical properties of the Al–Ni–Cu–Fe alloy manufactured by laser powder bed fusion10.1016/j.jmrt.2023.10.120 ↗
18. Effects of temperature and bimodal microstructure on the mechanical properties and fracture mechanisms of high-strength Al-Ni-Cu-Fe alloy fabricated through laser powder bed fusion
19. Design, microstructure and thermal stability of a novel heat-resistant Al-Fe-Ni alloy manufactured by selective laser melting10.1016/j.jallcom.2021.160949 ↗
20. Enhanced mechanical properties and thermal stability in additively manufactured Al-Ni alloy by Sc addition10.1016/j.jallcom.2022.167894 ↗
21. On the origin of a remarkable increase in the strength and stability of an Al rich Al-Ni eutectic alloy by Zr addition10.1016/j.actamat.2019.03.025 ↗
22. The solid-state combustion synthesis of in-situ hybrid (Al3Ni+Al2O3)/Al composites and evaluation of its mechanical properties10.1016/j.jallcom.2022.167917 ↗
23. Powder metallurgy aluminum alloys: structure and porosity
24. The coupling effect of vacuum, pressure and temperature on microstructure and mechanical properties of PM aluminum alloy10.1016/j.vacuum.2021.110728 ↗
25. Effects of cold and hot densification on the mechanical properties of a 7XXX series powder metallurgy alloy10.1179/174329009X409723 ↗
26. Study on mechanical and ballistic performances of boron carbide reinforced Al 6061 aluminum alloy produced by powder metallurgy10.1016/j.compositesb.2018.04.043 ↗
27. Microstructural evolution of a forged 2XXX series aluminum powder metallurgy alloy10.1016/j.matchar.2019.03.033 ↗
28. Microstructure and mechanical properties of powder metallurgy 2024 aluminum alloy during cold rolling10.1016/j.jmrt.2021.09.120 ↗
29. Processing methods and property evaluation of Al2O3 and SiC reinforced metal matrix composites based on aluminum 2xxx alloys10.1557/jmr.2016.131 ↗
30. On the simulation of wrought AA4032 via P/M processing10.1016/j.msea.2007.05.064 ↗
31. Effect of swaging and rolling post sintering treatments on the corrosion behaviour of Alumix 321 PM alloy10.1016/j.powtec.2017.07.034 ↗
32. Advancements in microstructure, texture characterization, and mechanical properties of powder metallurgy Al-Si-Mg-Fe alloy for engineering applications10.1016/j.jallcom.2023.172941 ↗
33. Effects of hyper-high-temperature solid-solution treatment on microstructure evolution and nanoprecipitation of the Al-Ni-Cu-Fe-Zr-Sc alloy manufactured by selective laser melting10.1016/j.jallcom.2021.160781 ↗
34. Industrial processing of a novel Al–Cu–Mg powder metallurgy alloy10.1016/j.msea.2012.09.049 ↗
35. Processing and microstructure of powder metallurgy Al-Fe-Ni alloys10.1007/BF02663431 ↗
36. Effect of hot deformation on microstructure and porosity of additively manufactured 7050 Al alloy10.1002/adem.202301124 ↗
37. Thermal mechanical processing of press and sinter Al-Cu-Mg-Sn-(AlN) metal matrix composite materials10.3390/met8070480 ↗
38. Regulating microstructures and mechanical properties of Al–Fe–Ni alloys10.1016/j.pnsc.2019.12.006 ↗
39. Metallurgical assessment of a hypereutectic aluminum–silicon P/M alloy10.1016/j.jmatprotec.2009.07.007 ↗
40. Effects of rolling deformation on precipitation behavior and mechanical properties of Al–Zn–Mg–Cu alloy10.1016/j.msea.2022.143342 ↗
41. Diffusional relaxation of stress concentration at second phase particles10.1016/0001-6160(78)90064-0 ↗
42. Effect of microalloying additions on microstructural evolution and thermal stability in cast Al-Ni alloys10.1016/j.jallcom.2024.174810 ↗
43. Coarsening-and creep resistance of precipitation-strengthened Al–Mg–Zr alloys processed by selective laser melting10.1016/j.actamat.2020.02.008 ↗
44. Achieving high strength-ductility synergy through high-density coherent precipitation in twin-roll cast Al–Zn–Mg–Cu strips10.1016/j.msea.2022.143592 ↗
45. Superposed hardening from precipitates and dislocations enhances strength-ductility balance in Al-Cu alloy10.1016/j.ijplas.2022.103413 ↗
46. Multiple quasicrystal approximants with the same lattice parameters in Al-Cr-Fe-Si alloys
47. Study of engineering developing decagonal-like rational approximant structure of Al–Ni–Cu–Fe–Mn–Cr senary system in aluminum alloy through additive manufacturing
48. Quasi‐crystals and their crystalline homologues in the Al60Mn11Ni4 ternary alloy10.1111/j.1365-2818.1988.tb04558.x ↗
49. Effect of Cu and Cr addition on the structure, anticorrosion and nanomechanical properties of new Al-Ni-Fe-(Cr, Cu) alloys10.1016/j.jallcom.2023.170839 ↗
50. Powder metallurgical processing of Sn-reinforced Al-Cu-Fe quasicrystals: structure, microstructure and toughening behavior
51. FCC rolling textures reviewed in the light of quantitative comparisons between simulated and experimental textures10.1080/10408436.2014.899485 ↗
52. Superior mechanical properties and microstructural evolution of powder metallurgy 2195 Al-Li alloy subjected to hot extrusion10.1016/j.jallcom.2023.171184 ↗
53. High-ductility powder metallurgy superalloy prepared using a new hot oscillatory pressing strategy10.1016/j.jallcom.2024.176633 ↗
54. Quasicrystals at high pressures and temperatures: a review10.1007/s12210-023-01183-z ↗
55. Chemical bonding and physical properties in quasicrystals and their related approximant phases: known facts and current perspectives10.3390/app9102132 ↗
56. Thermal stability of aluminum alloys10.3390/ma13153441 ↗