Porous structure and compressive failure mechanism of additively manufactured cubic-lattice tantalum scaffolds
Source abstract
Abstract
Additively manufactured tantalum scaffolds have attracted increased attention for their high potential for bone tissue reconstruction and other industrial applications. Porous structure designs, mechanical property evaluation, and material failure investigation are needed for this new structural and functional material. In this study, cubic lattice tantalum scaffolds with porosities of 65%, 75%, and 85% were designed and fabricated by selective laser melting, and the porous architecture and microstructure were characterized. The compressive mechanical behavior and material failure mechanism were explored by experimental compression tests and finite element analysis (FEA). The designed scaffold porous structure parameters included the following: side length of unit cell 880 μm, 1020 μm, and 1220 μm; pore size 380 μm, 520 μm, and 720 μm; and strut diameter 250 μm. The pore parameters of fabricated scaffolds matched well with those of the designed scaffolds. Struts were dense without macro/microscopic cracks and other microstructure defects resulting from laser melting. Porosity significantly affected the compressive mechanical properties. As the porosity decreased from 85% to 65%, the compressive strength and elastic modulus increased from 17.6±0.5 MPa and 0.7±0.2 GPa to 40.5±0.8 MPa and 1.5±0.6 GPa, respectively. Compression testing results indicated that additively manufactured cubic lattice tantalum scaffolds show ductile deformation behavior and excellent mechanical reliability. When the strain was as high as 50%, the scaffolds with different porosities exhibited plastic failure with progressive layer-by-layer collapse behavior determined by the coupling of buckling and bending deformation, demonstrating their high ductility. Collapse initially occurred in the upper and lower lattice layers of the scaffolds. Large deformation resulted in strut fracturing with micro crack propagation. Most of the fracturing sites were at the vertical struts and conjunctions, not the horizontal struts. FEA revealed that the stress was primarily concentrated on the vertical struts, and the struts in the upper and lower layers withstood greater stress than the struts in the middle layers. The stress in the vertical struts was distributed along the inclination angle of 45° with respect to the loading direction. Stress was not concentrated at the horizontal struts. The results of the FEA were consistent with the experimental results of the compression tests and showed that the load-bearing capability of cubic lattice tantalum scaffolds can be enhanced by increasing the diameter of the vertical struts.
Source: openalex_inverted_index · Quality: baseline
Research context
OpenAlex topics: Bone Tissue Engineering Materials · Additive Manufacturing and 3D Printing Technologies · Additive Manufacturing Materials and Processes
SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.
References (58)
Show source-provided references
1. Biocompatibility and osteogenesis of refractory metal implants, titanium, hafnium, niobium, tantalum and rhenium10.1016/S0142-9612(00)00275-1 ↗
2. Porous tantalum structures for bone implants: fabrication, mechanical and in vitro biological properties10.1016/j.actbio.2010.01.046 ↗
3. Experimental and clinical performance of porous tantalum in orthopedic surgery10.1016/j.biomaterials.2006.04.041 ↗
4. Tantalum is a good bone graft substitute in tibial tubercle advancement10.1007/s11999-009-1115-0 ↗
5. The physicochemical/biological properties of porous tantalum and the potential surface modification techniques to improve its clinical application in dental implantology10.1016/j.msec.2015.01.007 ↗
6. Characteristics of bone ingrowth and interface mechanics of a new porous tantalum biomaterial10.1302/0301-620X.81B5.0810907 ↗
7. Porous tantalum stimulates the proliferation and osteogenesis of osteoblasts from elderly female patients10.1002/jor.21251 ↗
8. Biocompatibility and osteogenic properties of porous tantalum10.3892/etm.2015.2208 ↗
9. Osseoincorporation of porous tantalum trabecular-structured metal: a histologic and histomorphometric study in humans10.11607/prd.3004 ↗
10. Structure, metallurgy, and mechanical properties of a porous tantalum foam10.1002/1097-4636(2001)58:2<180::AID-JBM1005>3.0.CO;2-5 ↗
11. Effect of porous tantalum on promoting the osteogenic differentiation of bone marrow mesenchymal stem cells in vitro through the MAPK/ERK signal pathway
12. In vitro and in vivo study of 3D-printed porous tantalum scaffolds for repairing bone defects10.1021/acsbiomaterials.8b01094 ↗
13. Porous tantalum VS. Titanium implants: enhanced mineralized matrix formation after stem cells proliferation and differentiation10.3390/jcm9113657 ↗
14. Mechanical performance of additively manufactured pure silver antibacterial bone scaffolds10.1016/j.jmbbm.2020.104090 ↗
15. Investigation of Ti64 sheathed cellular anatomical structure as a tibia implant10.1088/2057-1976/ab0bd7 ↗
16. Classification of biomaterial functionality
17. Additively manufactured porous tantalum implants10.1016/j.actbio.2014.12.003 ↗
18. Three-dimensional printed porous tantalum prosthesis for treating inflammation after total knee arthroplasty in one-stage surgery – a case report
19. Comparison of 3D-printed porous tantalum and titanium scaffolds on osteointegration and osteogenesis10.1016/j.msec.2019.109908 ↗
20. Tantalum bone implants printed by selective electron beam manufacturing (SEBM) and their clinical applications
21. Additive manufacturing of trabecular tantalum scaffolds by laser powder bed fusion: mechanical property evaluation and porous structure characterization10.1016/j.matchar.2020.110694 ↗
22. Mechanical properties of AlSi10Mg lattice structures fabricated by selective laser melting10.1016/j.matdes.2020.108709 ↗
23. Effects of scan line spacing on pore characteristics and mechanical properties of porous Ti6Al4V implants fabricated by selective laser melting10.1016/j.matdes.2014.05.021 ↗
24. Investigation of cell shape effect on the mechanical behaviour of open-cell metal foams
25. Architecture design of periodic truss-lattice cells for additive manufacturing
26. Influence of cell shape on mechanical properties of Ti–6Al–4V meshes fabricated by electron beam melting method10.1016/j.actbio.2014.06.010 ↗
27. Deformation behavior of heterogeneous multi-morphology lattice core hybrid structures
28. Influence of load orientation and of types of loads on the mechanical properties of porous Ti6Al4V biomaterials10.1016/j.matdes.2017.09.045 ↗
29. Mechanical properties of AM Ti6Al4V porous scaffolds with various cell structures10.1007/s12598-019-01231-4 ↗
30. The development status and trend of environmental friendly vacuum pressure impregnation resin at home and abroad
31. Bionic mechanical design and 3D printing of novel porous Ti6Al4V implants for biomedical applications10.1631/jzus.B1800622 ↗
32. The biomimetic design and 3D printing of customized mechanical properties porous Ti6Al4V scaffold for load-bearing bone reconstruction10.1016/j.matdes.2018.04.065 ↗
33. Dynamic Young's moduli of tungsten and tantalum at high temperature and stress10.1016/j.jnucmat.2010.12.222 ↗
34. Finite element analysis of Schwarz P surface pore geometries for tissue-engineered scaffolds
35. The influence of cell morphology on the compressive fatigue behavior of Ti-6Al-4V meshes fabricated by electron beam melting10.1016/j.jmbbm.2016.01.034 ↗
36. Finite element analysis of porous commercially pure titanium for biomedical implant application10.1016/j.msea.2018.04.009 ↗
37. Pore size of porous hydroxyapatite as the cell-substratum controls BMP-induced osteogenesis10.1093/oxfordjournals.jbchem.a021589 ↗
38. Bioresorbability, porosity and mechanical strength of bone substitutes: what is optimal for bone regeneration?10.1016/j.injury.2011.06.008 ↗
39. Superelastic behaviors of biomedical porous NiTi alloy with high porosity and large pore size prepared by spark plasma sintering10.1016/j.jallcom.2015.05.063 ↗
40. Application of combined porous tantalum scaffolds loaded with bone morphogenetic protein 7 to repair of osteochondral defect in rabbits10.1007/s00264-018-3800-7 ↗
41. Mesenchymal stem cell-loaded porous tantalum integrated with biomimetic 3D collagen-based scaffold to repair large osteochondral defects in goats10.1186/s13287-019-1176-2 ↗
42. R. Van Audekercke, M. Martens, Mechanical Properties of Cancellous Bone, Natural and Living Biomaterials, CRC Press2018, pp. 89-98.10.1201/9781351074902-6 ↗
43. Porosity of human mandibular condylar bone
44. Topological design and additive manufacturing of porous metals for bone scaffolds and orthopaedic implants: a review10.1016/j.biomaterials.2016.01.012 ↗
45. Cellular solids, structure and properties
46. Mechanical characterization of 3D printed multi-morphology porous Ti6Al4V scaffolds based on triply periodic minimal surface architectures
47. Titanium-based biomaterials for preventing stress shielding between implant devices and bone10.1155/2011/836587 ↗
48. Development of tantalum scaffold for orthopedic applications produced by space-holder method10.1016/j.matdes.2015.05.067 ↗
49. Effect of laser processing parameters on mechanical properties of porous tantalum fabricated by laser multi-layer micro-cladding10.1108/RPJ-05-2014-0068 ↗
50. Mechanical properties of cancellous tissue in compression test and nanoindentation
51. Biomechanics of trabecular bone10.1146/annurev.bioeng.3.1.307 ↗
52. Failure mechanisms of additively manufactured porous biomaterials: effects of porosity and type of unit cell10.1016/j.jmbbm.2015.06.012 ↗
53. CoCrMo cellular structures made by Electron Beam Melting studied by local tomography and finite element modelling10.1016/j.matchar.2016.04.006 ↗
54. Compressive properties of Ti-6Al-4V lattice structures fabricated by selective laser melting: design, orientation and density
55. Experimental characterization of SLM and EBM cubic lattice structures for lightweight Applications10.1007/s11340-019-00481-8 ↗
56. Mechanical properties of additively manufactured variable lattice structures of Ti6Al4V10.1016/j.msea.2021.140925 ↗
57. Finite element analysis of mechanical behavior, permeability of irregular porous scaffolds and lattice-based porous scaffolds10.1088/2053-1591/ab3ac1 ↗
58. Compression–compression fatigue behaviour of gyroid-type triply periodic minimal surface porous structures fabricated by selective laser melting10.1016/j.actamat.2019.09.042 ↗