Effect of tool rotational speed on friction stir spot welds of AZ31B Mg alloy to AISI 304 stainless steel
Source abstract
Abstract
Abstract AZ31B Mg alloy were welded to AISI 304 stainless steel (which is a very challenging task because of their huge different chemical and physical features) by friction stir spot welding (FSSW) at different tool rotation speeds (700, 1000, and 1300 rpm) while keeping other conditions the same. Welds were evaluated and compared by examining their cross-sectional geometry, XRD pattern, tensile shear strength, fracture way and area. From cross-sections of welds, it was obtained that joining area expanded when speed was enhanced and the weld made through 1300 rpm had the largest one. Therefore, weld fabricated with the highest speed of 1300 rpm displayed the biggest tensile shear load of 3741 N while that manufactured with the lowest speed of 700 rpm possessed the lowest of 2430 N. All welds showed tensile shear type fracture and fracture occurred from the hooking regions where joining took place. From the fracture joint region, the weld of 700 rpm had the smallest joined area, whereas that of 1300 rpm showed the biggest. Higher speed produced a stronger joint, which agreed with a bigger bonding area and broken joint region. Also, joint became more ductile with increasing speed. Some phases were detected in joints.
Source: crossref · Quality: baseline
Research context
OpenAlex topics: Advanced Welding Techniques Analysis · Aluminum Alloys Composites Properties · Aluminum Alloy Microstructure Properties
SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.
Affiliations
Astronautical Engineering Department, Sivas University of Science and Technology , Sivas, 58000 , Türkiye
References (68)
Show source-provided references
1. P. K. Mallick, Materials, Design and Manufacturing for Lightweight Vehicles, Sawston, Cambridge, UK, Elsevier, Woodhead Publishing, 2010.10.1533/9781845697822.2.275 ↗
2. S. M. Manladan, Y. Zhang, S. Ramesh, Y. Cai, S. Ao, and Z. Luo, “Resistance element welding of magnesium alloy and austenitic stainless steel in three-sheet configurations,” J. Mater. Process. Technol., vol. 274, 2019, Art. no. 116292, https://doi.org/10.1016/j.jmatprotec.2019.116292.10.1016/j.jmatprotec.2019.116292 ↗
3. Y. Li, Y. Liu, C. Liu, C. Li, Z. Ma, Y. Huang, Z. Wang, and W. Li, “Microstructure evolution and mechanical properties of linear friction welded S31042 heat-resistant steel,” J. Mater. Sci. Technol., vol. 34, no. 4, pp. 653–659, 2018, https://doi.org/10.1016/j.jmst.2017.11.031.10.1016/j.jmst.2017.11.031 ↗
4. R. S. Mishra and Z. Y. Ma, “Friction stir welding and processing,” Mater. Sci. Eng. Rep., vol. 50, nos. 1–2, pp. 1–78, https://doi.org/10.1016/j.mser.2005.07.001.10.1016/j.mser.2005.07.001 ↗
5. R. Nandan, T. DebRoy, and H. K. D. H. Bhadeshia, “Recent advances in friction-stir welding – process, weldment structure and properties,” Prog. Mater. Sci., vol. 53, no. 6, pp. 980–1023, 2008, https://doi.org/10.1016/j.pmatsci.2008.05.001.10.1016/j.pmatsci.2008.05.001 ↗
6. X. Cao, M. Jahazi, J. P. Immarigeon, and W. Wallace, “A review of laser welding techniques for magnesium alloys,” J. Mater. Process. Technol., vol. 171, no. 2, pp. 188–204, 2006, https://doi.org/10.1016/j.jmatprotec.2005.06.068.10.1016/j.jmatprotec.2005.06.068 ↗
7. G. S. Cole and A. M. Sherman, “Lightweight materials for automotive applications,” Mater. Charact., vol. 35, no. 1, pp. 3–9, 1995, https://doi.org/10.1016/1044-5803(95)00063-1.10.1016/1044-5803(95)00063-1 ↗
8. G. Song, T. Li, J. Yu, and L. Liu, “A review of bonding immiscible Mg/steel dissimilar metals,” Materials, vol. 11, no. 12, p. 2515, 2018, https://doi.org/10.3390/ma11122515.10.3390/ma11122515 ↗
9. D. Ren and L. Liu, “Interface microstructure and mechanical properties of arc spot welding Mg–steel dissimilar joint with Cu interlayer,” Mater. Des., vol. 59, pp. 369–376, 2014, https://doi.org/10.1016/j.matdes.2014.03.006.10.1016/j.matdes.2014.03.006 ↗
10. G. Song, G. An, and L. Liu, “Effect of gradient thermal distribution on butt joining of magnesium alloy to steel with Cu-Zn alloy interlayer by hybrid laser-tungsten inert gas welding,” Mater. Des., vol. 35, pp. 323–329, 2012, https://doi.org/10.1016/j.matdes.2011.09.006.10.1016/j.matdes.2011.09.006 ↗
11. S. Jana, Y. Hovanski, G. J. Grant, K. Mattlin, “Effect of tool feature on the joint strength of dissimilar friction stir lap welds,” Friction Stir Welding and Processing VI, San Diego, California, 2011, pp. 205–211.10.1002/9781118062302.ch25 ↗
12. L. Liu, L. Xiao, D. L. Chen, J. C. Feng, S. Kim, and Y. Zhou, “Microstructure and fatigue properties of Mg-to-steel dissimilar resistance spot welds,” Mater. Des., vol. 45, pp. 336–342, 2013, https://doi.org/10.1016/j.matdes.2012.08.018.10.1016/j.matdes.2012.08.018 ↗
13. W. M. Thomas, E. D. Nicholas, J. C. Needham, M. G. Murch, S. P. Temple, and C. J. Dawes, “Friction Stir Butt Welding,” International Patent Application No. PCT/GB92/02203, December, 1991.
14. S. Kumar and C. Wu, “Suppression of intermetallic reaction layer by ultrasonic assistance during friction stir welding of Al and Mg based alloys,” J. Alloys Compd., vol. 827, 2020, Art. no. 154343, https://doi.org/10.1016/j.jallcom.2020.154343.10.1016/j.jallcom.2020.154343 ↗
15. Z. Liang, K. Chen, X. Wang, J. Yao, Q. Yang, L. Zhang, and A. Shan, “Effect of tool offset and tool rotational speed on enhancing mechanical property of Al/Mg dissimilar FSW joints,” Metall. Mater. Trans. A, vol. 44, pp. 3721–3731, 2013, https://doi.org/10.1007/s11661-013-1700-4.10.1007/s11661-013-1700-4 ↗
16. J. Q. Su, T. W. Nelson, R. Mishra, and M. Mahoney, “Microstructural investigation of friction stir welded 7050-T651 aluminium,” Acta Mater., vol. 51, no. 3, pp. 713–729, 2003, https://doi.org/10.1016/S1359-6454(02)00449-4.10.1016/S1359-6454(02)00449-4 ↗
17. K. V. Jata, K. K. Sankaran, and J. Ruschau, “Friction stir welding effects on microstructure and fatigue of aluminum alloy 7050-T7451,” Metall. Mater. Trans. A, vol. 31, pp. 2181–2192, 2000, https://doi.org/10.1007/s11661-000-0136-9.10.1007/s11661-000-0136-9 ↗
18. C. G. Rhodes, M. W. Mahoney, W. H. Bingel, R. Spurling, and C. Bampton, “Effects of friction stir welding on microstructure of 7075 aluminium,” Scripta Mater., vol. 36, no. 1, pp. 69–75, 1997, https://doi.org/10.1016/S1359-6462(96)00344-2.10.1016/S1359-6462(96)00344-2 ↗
19. H. B. Chen, K. Yan, T. Lin, S. B. Chen, C. Y. Jiang, and Y. Zhao, “The investigation of typical welding defects for 5456 aluminum alloy friction stir welds,” Mater. Sci. Eng. A, vol. 433, nos. 1–2, pp. 64–69, 2006, https://doi.org/10.1016/j.msea.2006.06.056.10.1016/j.msea.2006.06.056 ↗
20. R. Rai, A. De, H. K. D. H. Bhadeshia, and T. DebRoy, “Review: friction stir welding tools,” Sci. Technol. Weld. Join., vol. 16, no. 4, pp. 325–342, 2011, https://doi.org/10.1179/1362171811Y.0000000023.10.1179/1362171811Y.0000000023 ↗
21. P. Pourahmad and M. Abbasi, “Materials flow and phase transformation in friction stir welding of Al 6013/Mg,” Trans. Nonferrous Metals Soc. China, vol. 23, no. 5, pp. 1253–1261, 2013, https://doi.org/10.1016/S1003-6326(13)62590-X.10.1016/S1003-6326(13)62590-X ↗
22. B. Fu, G. Qin, F. Li, X. Meng, J. Zhang, and C. Wu, “Friction stir welding process of dissimilar metals of 6061-T6 aluminum alloy to AZ31B magnesium alloy,” J. Mater. Process. Technol., vol. 218, pp. 38–47, 2015, https://doi.org/10.1016/j.jmatprotec.2014.11.039.10.1016/j.jmatprotec.2014.11.039 ↗
23. Y. C. Chen and K. Nakata, “Microstructural characterization and mechanical properties in friction stir welding of aluminum and titanium dissimilar alloys,” Mater. Des., vol. 30, no. 3, pp. 469–474, 2009, https://doi.org/10.1016/j.matdes.2008.06.008.10.1016/j.matdes.2008.06.008 ↗
24. I. Galvão, D. Verdera, D. Gesto, A. Loureiro, and D. M. Rodrigues, “Influence of aluminium alloy type on dissimilar friction stir lap welding of aluminium to copper,” J. Mater. Process. Technol., vol. 213, no. 11, pp. 1920–1928, 2013, https://doi.org/10.1016/j.jmatprotec.2013.05.004.10.1016/j.jmatprotec.2013.05.004 ↗
25. J. Zhang, Y. Shen, X. Yao, H. Xu, and B. Li, “Investigation on dissimilar underwater friction stir lap welding of 6061-T6 aluminum alloy to pure copper,” Mater. Des., vol. 64, pp. 74–80, 2014, https://doi.org/10.1016/j.matdes.2014.07.036.10.1016/j.matdes.2014.07.036 ↗
26. Y. C. Chen and K. Nakata, “Effect of tool geometry on microstructure and mechanical properties of friction stir lap welded magnesium alloy and steel,” Mater. Des., vol. 30, no. 9, pp. 3913–3919, 2009, https://doi.org/10.1016/j.matdes.2009.03.007.10.1016/j.matdes.2009.03.007 ↗
27. Y. Meng, Y. Ma, S. Chen, Y. Han, S. Chen, J. Huang, and J. Yang, “Friction stir butt welding of magnesium alloy to steel by truncated cone-shaped stirring pin with threads,” J. Mater. Process. Technol., vol. 291, 2021, Art. no. 117038, https://doi.org/10.1016/j.jmatprotec.2020.117038.10.1016/j.jmatprotec.2020.117038 ↗
28. D. Kim, H. Badarinarayan, I. Ryu, J. H. Kim, C. Kim, K. Okamoto, R. H. Wagoner, and K. Chung, “Numerical simulation of friction stir spot welding process for aluminum alloys,” Met. Mater. Int., vol. 16, pp. 323–332, 2010, https://doi.org/10.1007/s12540-010-0425-9.10.1007/s12540-010-0425-9 ↗
29. A. Arici and S. Mert, “Friction stir spot welding of polypropylene,” J. Reinf. Plast. Compos., vol. 27, no. 18, pp. 2001–2004, 2008, https://doi.org/10.1177/0731684408089134.10.1177/0731684408089134 ↗
30. S. Lathabai, M. Painter, G. Cantin, and V. Tyagi, “Friction spot joining of an extruded Al–Mg–Si alloy,” Scripta Mater., vol. 55, no. 10, pp. 899–902, 2006, https://doi.org/10.1016/j.scriptamat.2006.07.046.10.1016/j.scriptamat.2006.07.046 ↗
31. A. Gerlich, P. Su, M. Yamamoto, and T. H. North, “Effect of welding parameters on the strain rate and microstructure of friction stir spot welded 2024 aluminum alloy,” J. Mater. Sci., vol. 42, pp. 5589–5601, 2007, https://doi.org/10.1007/s10853-006-1103-7.10.1007/s10853-006-1103-7 ↗
32. P. H. Thornton, A. R. Krause, and R. G. Davies, “The aluminum spot weld,” Weld. J., vol. 75, no. 3, pp. 101–108, 1996.
33. A. Gean, S. A. Westgate, J. C. Kucza, and J. C. Ehrstrom, “Static and fatigue behavior of spot-welded 51 82–0 aluminum alloy sheet,” Weld. J., vol. 78, no. 3, pp. 80–86, 1999.
34. B. Irving, “Why aren’t airplanes welded?” Weld. J., vol. 76, no. 1, pp. 31–41, 1997.
35. C. B. Smith, J. F. Hinrichs, P. C. Ruehl, Friction Stir and Friction Stir Spot Welding-Lean, Mean, and Green, Sheet Metal Welding Conference XI, Paper 2–5, Sterling heights, MI, May 11–14, 2004.
36. Y. Uematsu and K. Tokaji, “Comparison of fatigue behaviour between resistance spot and friction stir spot welded aluminium alloy sheets,” Sci. Technol. Weld. Join., vol. 14, no. 1, pp. 62–71, 2009, https://doi.org/10.1179/136217108X338908.10.1179/136217108X338908 ↗
37. Z. H. Zhang, X. Q. Yang, J. L. Zhang, G. Zhou, X. D. Xu, and B. L. Zou, “Effect of welding parameters on microstructure and mechanical properties of friction stir spot welded 5052 aluminum alloy,” Mater. Des., vol. 32, nos. 8–9, pp. 4461–4470, 2011, https://doi.org/10.1016/j.matdes.2011.03.058.10.1016/j.matdes.2011.03.058 ↗
38. D. Mitlin, V. Radmilovic, T. Pan, J. Chen, Z. Feng, and M. L. Santella, “Structure–properties relations in spot friction welded (also known as friction stir spot welded) 6111 aluminum,” Mater. Sci. Eng. A, vol. 441, nos. 1–2, pp. 79–96, 2006, https://doi.org/10.1016/j.msea.2006.06.126.10.1016/j.msea.2006.06.126 ↗
39. P. Briskham, N. Blundell, L. Han, R. Hewitt, and K. Young, “Comparison of self-pierce riveting, resistance spot welding and spot friction joining for aluminium automotive sheet,” in SAE Special Publication SP-2034, SAE Technical Paper 2006-01-0774, USA, Warrendale.10.4271/2006-01-0774 ↗
40. A. Gerlich, P. Su, T. H. North, and G. J. Bendzsak, “Friction stir spot welding of aluminum and magnesium alloys,” Mater. Forum, vol. 29, pp. 290–294, 2005, https://doi.org/10.4271/2005-01-1255.10.4271/2005-01-1255 ↗
41. K. Miyagawa, M. Tsubaki, T. Yasui, and M. Fukumoto, “Spot welding between aluminium alloy and low-carbon steel by friction stirring,” Weld. Int., vol. 23, no. 8, pp. 559–564, 2009, https://doi.org/10.1080/09507110802543039.10.1080/09507110802543039 ↗
42. Y. Uematsu, T. Kakiuchi, Y. Tozaki, and H. Kojin, “Comparative study of fatigue behaviour in dissimilar Al alloy/steel and Mg alloy/steel friction stir spot welds fabricated by scroll grooved tool without probe,” Sci. Technol. Weld. Join., vol. 17, no. 5, pp. 348–356, 2012, https://doi.org/10.1179/1362171812Y.0000000014.10.1179/1362171812Y.0000000014 ↗
43. S. Bozzi, A. L. Etter, T. Baudin, V. Klosek, J. G. Kerbiguet, and B. Criqui, “Influence of FSSW parameters on fracture mechanisms of 5182 aluminium welds,” J. Mater. Process. Technol., vol. 210, no. 11, pp. 1429–1435, 2010, https://doi.org/10.1016/j.jmatprotec.2010.03.022.10.1016/j.jmatprotec.2010.03.022 ↗
44. R. Z. Xu, D. R. Ni, Q. Yang, C. Z. Liu, and Z. Y. Ma, “Influence of Zn interlayer addition on microstructure and mechanical properties of friction stir welded AZ31 Mg alloy,” J. Mater. Sci., vol. 50, pp. 4160–4173, 2015, https://doi.org/10.1007/s10853-015-8841-3.10.1007/s10853-015-8841-3 ↗
45. Y. C. Chen and K. Nakata, “Friction stir lap welding of magnesium alloy and zinc-coated steel,” Mater. Trans., vol. 50, no. 11, pp. 2598–2603, 2009, https://doi.org/10.2320/matertrans.M2009022.10.2320/matertrans.M2009022 ↗
46. Y. Chen, J. Chen, B. ShalchiAmirkhiz, M. J. Worswick, and A. P. Gerlich, “Microstructures and properties of Mg alloy/DP600 steel dissimilar refill friction stir spot welds,” Sci. Technol. Weld. Join., vol. 20, no. 6, pp. 494–501, 2015, https://doi.org/10.1179/1362171815Y.0000000033.10.1179/1362171815Y.0000000033 ↗
47. Specimens Dimensions and Procedure for Shear Testing Resistance Spot and Embossed Projection Welded Joints, JIS Z 3136, Japanese Standards Association, Tokyo, Japan, 1999.
48. Q. Yang, S. Mironov, Y. S. Sato, and K. Okamoto, “Material flow during friction stir spot welding,” Mater. Sci. Eng. A, vol. 527, no. 16–17, pp. 4389–4398, 2010, https://doi.org/10.1016/j.msea.2010.03.082.10.1016/j.msea.2010.03.082 ↗
49. O. O. Ojo, E. Taban, and E. Kaluc, “Effect of residual Alclad on friction stir spot welds of AA2219 alloys,” Mater. Test., vol. 60, no. 10, pp. 979–988, 2018, https://doi.org/10.3139/120.111245.10.3139/120.111245 ↗
50. X. Fu, K. Chen, C. Liu, M. Wang, and X. Hua, “Microstructure and mechanical properties of dissimilar friction stir lap welding between AZ31 Mg alloy and DC01 steel,” Mater. Charact., vol. 187, 2022, Art. no. 111870, https://doi.org/10.1016/j.matchar.2022.111870.10.1016/j.matchar.2022.111870 ↗
51. H. I. Khalaf, R. Al-Sabur, and H. A. Derazkola, “Effect of number of tool shoulders on the quality of steel to magnesium alloy dissimilar friction stir welds,” Arch. Civ. Mech. Eng., vol. 23, p. 125, 2023, https://doi.org/10.1007/s43452-023-00673-z.10.1007/s43452-023-00673-z ↗
52. Y. Ding, G. You, H. Wen, P. Li, X. Tong, and Y. Zhou, “Microstructure and mechanical properties of inertia friction welded joints between alloy steel 42CrMo and cast Ni-based superalloy K418,” J. Alloys Compd., vol. 803, no. 30 September, pp. 176–184, 2019, https://doi.org/10.1016/j.jallcom.2019.06.136.10.1016/j.jallcom.2019.06.136 ↗
53. J. R. Davis, ASM Specialty Handbook: Aluminum and Aluminum Alloys, Novelty, OH, USA, ASM International, 2007, pp. 41–46.
54. V. G. Davydov, T. D. Rostova, V. V. Zakharov, Y. A. Filatov, and V. I. Yelagin, “Scientific principles of making an alloying addition of scandium to aluminium alloys,” Mater. Sci. Eng. A, vol. 280, no. 1, pp. 30–36, 2000, https://doi.org/10.1016/S0921-5093(99)00652-8.10.1016/S0921-5093(99)00652-8 ↗
55. K. E. Knipling, D. N. Seidma, and D. C. Dunand, “Ambient- and high- temperature mechanical properties of isochronally aged Al-0.06Sc, Al-0.06Zr and Al-0.06Sc-0.06Zr (at.%) alloys,” Acta Mater., vol. 59, no. 3, pp. 943–954, 2011, https://doi.org/10.1016/j.actamat.2010.10.017.10.1016/j.actamat.2010.10.017 ↗
56. J. Liu, P. Yao, N. Q. Zhao, C. S. Shi, H. J. Li, X. Li, D. S. Xi, and S. Yang, “Effect of mi-nor Sc and Zr on recrystallization behavior and mechanical properties of novel Al-Zn-Mg-Cu alloys,” J. Alloys Compd., vol. 657, pp. 717–725, 2016, https://doi.org/10.1016/j.jallcom.2015.10.122.10.1016/j.jallcom.2015.10.122 ↗
57. J. R. Davis and Associates, Aluminum and Aluminum Alloys Handbook, Prepared under the direction of the ASM International Handbook Commitee, Materials Park, OH, ASM International, 1993.
58. K. S. Abdel-Halim, M. Bahgat, and O. A. Fouad, “Thermal synthesis of nanocrystalline fcc Fe-Ni alloy by gaseous reduction of coprecipitated NiFe2O4 from secondary resources,” J. Mater. Sci. Technol., vol. 22, no. 12, pp. 1396–1400, 2006, https://doi.org/10.1179/174328406X131019.10.1179/174328406X131019 ↗
59. J. Lee, S. Lee, J. Heo, and O. SungCho, “Feasibility of cathodic plasma electrolytic oxidation for corrosion resistant stainless steel against chloride-based matter,” Transactions of the Korean Nuclear Society Virtual Spring Meeting July 9–10, 2020.
60. A. Mani, S. Mohan, G. Renganathan, K. Athinarayanaswamy, and R. Srinivasan, “Non-stoichiometric Cu3.8 Ni phase in electrochemically layered Cu-Ni thin films,” J. Mater. Sci. Lett., vol. 15, no. 12, 1996, https://doi.org/10.1007/bf00274902.10.1007/BF00274902 ↗
61. I. Nikulin, A. Kipelova, S. Malopheyev, and R. Kaibyshev, “Effect of second phase particles on grain refinement during equal-channel angular pressing of an Al–Mg–Mn alloy,” Acta Mater., vol. 60, no. 2, pp. 487–497, 2012, https://doi.org/10.1016/j.actamat.2011.10.023.10.1016/j.actamat.2011.10.023 ↗
62. Y. Wang, B. Yang, M. Gao, and R. Guan, “Deformation behavior and dynamic recrystallization during hot compression in homogenized Al–6Mg–0.8Mn alloys,” Mater. Sci. Eng. A, vol. 840, 2022, Art. no. 142953, https://doi.org/10.1016/j.msea.2022.142953.10.1016/j.msea.2022.142953 ↗
63. J. Liao, N. Yamamoto, and K. Nakata, “Effect of dispersed intermetallic particles on microstructural evolution in the friction stir weld of a fine-grained magnesium alloy,” Metall. Mater. Trans. A, vol. 40, pp. 2212–2219, 2009, https://doi.org/10.1007/s11661-009-9921-2.10.1007/s11661-009-9921-2 ↗
64. L. Cao, Y. Liu, H. C. Chen, L. Zhang, H. Sun, and G. Bi, “Investigation of intermetallics formation and joint performance of laser welded Ni to Al,” Appl. Sci., vol. 13, no. 3, p. 1356, 2023, https://doi.org/10.3390/app13031356.10.3390/app13031356 ↗
65. U. Özdemir, S. Sayer, and Ç. Yeni, “Effect of pin penetration depth on the mechanical properties of friction stir spot welded aluminum and copper,” Mater. Test., vol. 54, no. 4, pp. 233–239, 2012, https://doi.org/10.3139/120.110322.10.3139/120.110322 ↗
66. O. Ekinci and Z. Balalan, “Influence of tool pin shape and rotation speed for friction stir spot welding of AZ91 magnesium alloy sheets,” Mater. Test., vol. 65, no. 8, pp. 1281–1291, 2023, https://doi.org/10.1515/mt-2023-0016.10.1515/mt-2023-0016 ↗
67. X. J. Wang, Y. L. Wu, Z. K. Zhang, T. K. Guo, Y. X. Lu, and J. P. Shi, “The study of the microstructure and mechanical properties of friction stir spot welding joint between AZ31B magnesium alloy and steel,” Adv. Mater. Res., vol. 668, pp. 818–822, 2013, https://doi.org/10.4028/www.scientific.net/AMR.668.818.10.4028/www.scientific.net/AMR.668.818 ↗
68. F. Sarsilmaz and B. G. Çelik, “Microstructural and numerical variation of friction spot welded AA7075 couples,” Mater. Test., vol. 65, no. 9, pp. 1373–1381, 2023, https://doi.org/10.1515/mt-2023-0142.10.1515/mt-2023-0142 ↗