journal article·2026-03-26

Online monitoring of friction stir welding of dissimilar aluminum alloys

Senthilkumar Kannaiyan, Seeman Murugesan, Thirumalaikannan Dhamotharakannan, Sivaraj Paramasivam

Materials Testing· Volume 68· Issue 3
Publisher page

Abstract

Abstract Friction stir welding (FSW) provides an effective solution for joining dissimilar aluminum alloys like AA5083 and AA6061-T6, which are prone to issues like porosity and cracking when welded using conventional fusion methods. This study investigates the use of real-time acoustic emission (AE) monitoring to evaluate weld quality and detect defects such as piping and pinholes during the FSW process. Key AE parameters, including RMS, Hits, Amplitude, Counts, and AE Fast Fourier Transform (FFT) spectra, were examined alongside waveform characteristics. Mechanical testing revealed that defect-free joints achieved a tensile strength of 256 MPa and 82 % joint efficiency, whereas the presence of piping and pinhole defects lowered the strength to 235 MPa and 201 MPa, respectively. Microstructural analysis confirmed the formation of finer grains and higher hardness (93 Hv) in the stir zone of defect-free welds. AE Parametric monitoring showed marked increases in signal intensity in defective welds, especially those with pipping and pinhole defects, validating its potential for defect identification. Shifts in AE FFT spectra peak amplitude frequencies and distinct burst-type waveforms further demonstrated the capability of AE analysis to characterize weld conditions. These findings highlight the effectiveness of AE techniques as a nondestructive, real-time tool for monitoring weld integrity in industrial applications.
Source: crossref · Quality: baseline

Research context

OpenAlex topics: Advanced Welding Techniques Analysis · Aluminum Alloy Microstructure Properties · Welding Techniques and Residual Stresses

SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.

Affiliations

Manufacturing Engineering , 364052 Annamalai University Faculty of Engineering and Technology , Annamalai Nagar , India

Manufacturing Engineering , Annamalai University , Annamalai Nagar , India

References (48)

Show source-provided references
1. S. Kannan, B. Murugan, K. Moorthy, and J. Kumar, “Material flow and mechanical properties of friction stir welded AA 5052-H32 and AA6061-T6 alloys with Sc interlayer,” Mater. Test., vol. 65, no. 7, pp. 1127–1142, 2023, https://doi.org/10.1515/mt-2022-0352.10.1515/mt-2022-0352 ↗
2. N. N. Rajesh Jesudoss Hynes, M. Vivek Prabhu, and C. I. Pruncu, “An experimental insight of friction stir welding of dissimilar AA 6061/Mg AZ 31 B joints,” J. Eng. Manuf., vol. 236, nos. 6–7, pp. 1–21, 2021. https://doi.org/10.1177/09544054211043474.10.1177/09544054211043474 ↗
3. T. Dhamothara Kannan, P. Sivaraj, V. Balasubramanian, T. Sonar, M. Ivanov, and S. Murugaesan, “Microstructural characteristics and mechanical properties of rotary friction-welded dissimilar AISI 431 steel/AISI 1018 steel joints,” J. Mech. Behav. Mater., vol. 32, no. 1, p. 20220273, 2023, https://doi.org/10.1515/jmbm-2022-0273.10.1515/jmbm-2022-0273 ↗
4. F. Tolun, “Effect of tool rotational speed and position on mechanical and microstructural properties of friction stir welded dissimilar alloys AZ31B Mg and Al6061,” Mater. Test., vol. 64, no. 5, pp. 714–725, 2022, https://doi.org/10.1515/mt-2021-2080.10.1515/mt-2021-2080 ↗
5. T. Dhamothara Kannan, P. Sivaraj, and M. Seeman, “Mechanical and metallurgical characteristics of rota¬ry friction welded low carbon steel plate/rod joints,” Key Eng. Mater., vol. 934, no. 1, pp. 153–160, 2022. https://doi.org/10.4028/p-51a271.10.4028/p-51a271 ↗
6. A. Yürük, B. Bekir, and K. Nizamettin, “Microstructure and mechanical properties of friction stir welded dissimilar 5754-H111-6013-T6 aluminum alloy joints,” Mater. Test., vol. 61, no. 10, pp. 941–946, 2019, https://doi.org/10.3139/120.111404.10.3139/120.111404 ↗
7. T. Dhamothara Kannan, P. Sivaraj, V. Balasubramanian, T. Sonar, and M. Seeman, “Predicting mechanical properties of friction welded AISI 1020/AISI 1018 steel and AISI 431/AISI 1018 steel joints,” SAE Int. J. Mater. Manuf., vol. 6, no. 2, pp. 157–174, 2023, https://www.jstor.org/stable/27350497.10.4271/05-16-02-0013 ↗
8. C. Rajendran, S. Kasi, V. Balasubramanian, B. Haridasu, V. Kumar Mari, and R. Seerangan, “Dynamic recrystallization in friction stir welded AA2014 aluminium alloy joints to replace riveted joints,” Mater. Test., vol. 65, no. 7, pp. 1085–1096, 2023. https://doi.org/10.1515/mt-2022-0351.10.1515/mt-2022-0351 ↗
9. D. Kanagarajan, P. Sivaraj, M. Seeman, and R. Seetharaman, “Evaluation of the reliability on WC-40 % Co composites through Weibull analysis,” Mater.Tod. Proc., vol. 22, no. 2, pp. 519–524, 2020. https://doi.org/10.1016/j.matpr.2019.08.124.10.1016/j.matpr.2019.08.124 ↗
10. H. Jia, K. Wu, Y. Sun, F. Hu, and G. Chen, “Evaluation of axial force, tool torque and weld quality of friction stir welded dissimilar 6061/5083 aluminum alloys,” CIRP J. Manuf. Sci. Tech., vol. 37, no. 17, pp. 267–277, 2022. https://doi.org/10.1016/j.cirpj.2022.02.003.10.1016/j.cirpj.2022.02.003 ↗
11. P. Tayebi, A. Fazli, P. Asadi, and M. Soltanpour, “Formability analysis of dissimilar friction stir welded AA 6061 and AA 5083 blanks by SPIF process,” CIRP J. Manufac. Sci. Tech., vol. 25, no. 3, pp. 50–68, 2019. https://doi.org/10.1016/j.cirpj.2019.02.002.10.1016/j.cirpj.2019.02.002 ↗
12. G. Di Bella, F. Favaloro, and C. Borsellino, “Effect of process parameters on friction stir welded joints between dissimilar aluminum alloys, A review,” Metals, vol. 3, no. 7, p. 1176, 2023, https://doi.org/10.3390/met13071176.10.3390/met13071176 ↗
13. N. Malleswararao Battina, V. Siva Prasad Vanthala, and H. Krishna, “Effect of friction stir welding process parameters on mechanical and metallurgical behavior of AA6061-T6 and AA2017-T6 tailored blanks,” Eng. Res. Exp., vol. 3, no. 2, p. 025043, 2021. https://doi.org/10.1088/2631-8695/ac09d9.10.1088/2631-8695/ac09d9 ↗
14. T. Łazińska, M. Szachogłuchowicz, K. Grzelak, I. Szachogłuchowicz, and J. Mierzyński, “Microstructure and mechanical properties of dissimilar friction stir welded joint AA7020/AA5083 with different joining parameters,” Materials, vol. 15, no. 5, p. 1910, 2022. https://doi.org/10.3390/ma15051910.10.3390/ma15051910 ↗
15. S. Balamurugan, K. Jayakumar, and C. Nandakumar, “Investigation of mechanical, metallurgical and corrosion characteristics of friction stir welded dissimilar AA 5052-H32 and AA 6061-T6 joints,” J. Chin. Inst. Eng., vol. 46, no. 6, pp. 601–614, 2022. https://doi.org/10.1080/02533839.2023.2227875.10.1080/02533839.2023.2227875 ↗
16. S. Verma and V. Kumar, “Optimization of Friction Stir Welding Parameters of Dissimilar Aluminium Alloys 6061 and 5083 by Using Response Surface Methodology,” Proc. Inst. Mech. Eng. C: J. Mech. Eng. Sci., vol. 235, no. 23, pp. 7009–7020, 2021. https://doi.org/10.1177/09544062211005804.10.1177/09544062211005804 ↗
17. M. Makeshkumar, S. R. Surender, S. Arunprakash, R. Madesh, M. Sasi Kumar, and K. Sudharsan, “Microstructural and mechanical properties evaluation of dissimilar aluminum alloy and bronze joints using friction stir welding,” Mat. Today Proc., vol. 47, no. 15, pp. 5239–5244, 2021. https://doi.org/10.1016/j.matpr.2021.05.563.10.1016/j.matpr.2021.05.563 ↗
18. S. Mahmut Aktarer, D. Murat Sekban, T. Kucukomeroglu, and G. Purcek, “Microstructure, mechanical properties and formability of friction stir welded dissimilar materials of IF-steel and 6061 Al alloy,” Int. J. Min. Metal. Mat., vol. 26, no. 10, pp. 722–731, 2019. https://doi.org/10.1007/s12613-019-1783-z.10.1007/s12613-019-1783-z ↗
19. D. D. Ambrosio, G. Wagner, V. Yahiaoui, M. Paris, J. Y. Fazzini, and M. Cahuc, “Olivier, “On the potential applications of acoustic emission in friction stir welding,” J. Manuf. Pro., vol. 75, no. 1, pp. 461–475, 2022. https://doi.org/10.1016/j.jmapro.2022.01.012.10.1016/j.jmapro.2022.01.012 ↗
20. T. Vié, S. Deschanel, N. Godin, and B. Normand, “On the effect of coatings on the tensile and fatigue properties of 7075-T6 aluminum alloy monitored with Acoustic Emission (AE): Towards lifetime estimation,” Int. J. Fatigue, vol. 171, no. 6, p. 107578, 2023. https://doi.org/10.1016/j.ijfatigue.2023.107578.10.1016/j.ijfatigue.2023.107578 ↗
21. J. B. Hunt, B. A. Mazzeo, C. D. Sorensen, and Y. Hovanski, “A generalized method for In-Process defect detection in friction stir welding,” J. Manuf. Mat. Process., vol. 6, no. 4, p. 80, 2022, https://doi.org/10.3390/jmmp6040080.10.3390/jmmp6040080 ↗
22. P. Rabe, A. Schiebahn, and U. Reisgen, “Force feedback-based quality monitoring of the friction stir welding process utilizing an analytic algorithm,” Weld World., vol. 65, no. 5, pp. 845–854, 2020. https://doi.org/10.1007/s40194-020-01044-5.10.1007/s40194-020-01044-5 ↗
23. X. He, Z. Yan, H. Liang, and D. Wang, “Corrosion fatigue acoustic emission characteristics and evaluation of friction stir welding joints of AZ31 magnesium alloy in 3.5 wt.% NaCl solution,” J. Mater. Res. Tech., vol. 25, no. 19, pp. 4582–4594, 2023. https://doi.org/10.1016/j.jmrt.2023.06.240.10.1016/j.jmrt.2023.06.240 ↗
24. S. Senthilkumar, S. Narayanan, and S. Denis Ashok, “Acoustic emission–based monitoring approach for friction stir welding of aluminum alloy AA6063-T6 with different tool pin profiles,” Proc. Inst. Mech. Eng. B: J. Eng. Manuf., vol. 227, no. 3, pp. 407–416, 2013. https://doi.org/10.1177/0954405412472673.10.1177/0954405412472673 ↗
25. X. Yao, B. S. Vien, C. Davies, and W. K. Chiu, “Acoustic emission source characterisation during fatigue crack growth in Al 2024-T3 specimens,” Sensors, vol. 22, no. 22, p. 8796, 2022, https://doi.org/10.3390/s22228796.10.3390/s22228796 ↗
26. B. Wisner et al.., “Acoustic emission signal processing framework to identify fracture in aluminum alloys,” Eng. Frac. Mech., vol. 210, no. 14, pp. 367–380, 2019. https://doi.org/10.1016/j.engfracmech.2018.04.027.10.1016/j.engfracmech.2018.04.027 ↗
27. W. Mu, Y. Gao, Y. Wang, G. Liu, and H. Hu, “Modeling and analysis of acoustic emission generated by fatigue cracking,” Sensors, vol. 22, no. 3, p. 1208, 2022, https://doi.org/10.3390/s22031208.10.3390/s22031208 ↗
28. N. Angelopoulos and V. Kappatos, “An experimental assessment using acoustic emission sensors to effectively detect surface deterioration on steel plates,” Sensors, vol. 24, no. 19, p. 6462, 2024, https://doi.org/10.3390/s24196462.10.3390/s24196462 ↗
29. A. N. Salah, H. Mehdi, A. Mehmood, A. W. Hashmi, C. Malla, and R. Kumar, “Optimization of process parameters of friction stir welded joints of dissimilar aluminum alloys AA3003 and AA6061 by RSM,” Mater. Today: Proc., vol. 56, no. 4, pp. 1675–1683, 2022, https://doi.org/10.1016/j.matpr.2021.10.288.10.1016/j.matpr.2021.10.288 ↗
30. M. Mohammadi Sefat, H. Ghazanfari, and C. Blais, “Friction stir welding of 5052-H18 aluminum alloy: Modeling and process parameter optimization,” J. Mater. Eng. Perf., vol. 30, no. 1–2, pp. 1838–1850, 2021. https://doi.org/10.1007/s11665-021-05499-5.10.1007/s11665-021-05499-5 ↗
31. C. Zhang, G. Huang, Y. Cao, Q. Li, L. Niu, and Q. Liu, “Characterizations of microstructure, crystallographic texture and mechanical properties of dissimilar friction stir welding joints for AA2024 and AA7075 under different tool shoulder end profiles,” Mat. Today Com., vol. 25, no. 30, p. 101435, 2020. https://doi.org/10.1016/j.jmrt.2021.09.037.10.1016/j.mtcomm.2020.101435 ↗
32. A. R. I. F. Wahyudianto, M. N. Ilman, P. T. Iswanto, A. Kusmono, and A. Akhyar, “The effect of tool rotation speed on hardness, tensile strength, and microstructure of dissimilar friction stir welding of dissimilar AA5083 and AA6061-T6 alloys,” Key Eng. Mater., vol. 892, no. 1, pp. 159–168, 2021. https://doi.org/10.4028/www.scientific.net/KEM.892.159.10.4028/www.scientific.net/KEM.892.159 ↗
33. S. Nishant, S. K. Jha, and P. Prakash, “Welding speed effects in underwater and conventional friction stir welding of dissimilar aluminum alloy 6061-T6 and 5083-H12 joints,” Proc. Inst. Mech. Eng. B: J. Eng. Manuf., vol. 15, no. 3, pp. 450–465, 2025. https://doi.org/10.1177/09544054241311327.10.1177/09544054241311327 ↗
34. S. Nishant, S. K. Jha, and P. Prakash, “Effect of tool rotation speed on mechanical properties of underwater friction stir welding of 6061-T6 and 5083-H12 aluminium alloys,” Mat. Today: Proc., vol. 91, no. 1, pp. 138–142, 2023, https://doi.org/10.1016/j.matpr.2023.05.727.10.1016/j.matpr.2023.05.727 ↗
35. S. Verma and V. Kumar, “Optimization of friction stir welding parameters of dissimilar aluminium alloys 6061 and 5083 by using response surface methodology,” Proc. Ins. Mech. Eng., Part C: J. Mech. Eng. Sci., vol. 235, no. 23, pp. 7009–7020, 2021, https://doi.org/10.1177/09544062211005804.10.1177/09544062211005804 ↗
36. K. Senthil Kumar, M. Seeman, P. Sivaraj, and V. Balasubramanian, “Mechanical properties and metallurgical characteristics of friction stir welded dissimilar AA5083/AA6061 aluminum alloy joints,” AIP Conf. Pro., vol. 2747, no. 1, p. 030002, 2023, https://doi.org/10.1063/5.0132618.10.1063/5.0132618 ↗
37. R. S. Mishra and P. Rani, “Experimental investigation of joining of aluminum alloy 5083 by friction stir welding (FSW),” Int. J. Res. Eng. Innov., vol. 3, no. 5, pp. 306–309, 2019.10.36037/IJREI.2019.3504 ↗
38. G. Di Bella, C. Borsellino, M. Chairi, D. Campanella, and G. Buffa, “Effect of rotational speed on mechanical properties of AA5083/AA6082 friction stir welded T-Joints for naval applications,” Metals, vol. 14, no. 12, p. 1410, 2024. https://doi.org/10.3390/met14121410.10.3390/met14121410 ↗
39. P. Satish Kumar and M. Shiva Chander, “Effect of tool pin geometry on FSW dissimilar aluminum alloys (AA5083 & AA6061),” Mat. Today. Proc., vol. 39, pp. 472–477, 2020, https://doi.org/10.1016/j.matpr.2020.08.204.10.1016/j.matpr.2020.08.204 ↗
40. A. R. Essa, A. R. Aboud, M. M. Ahmed, A. E. El-Nikhaily, A. S. Easa, and M. I. Habba, “Friction stir welding of aluminum alloy 6082-T6 using eccentric shoulder tools to eliminate the need for tool tilting,” Sci. Rep., vol. 15, no. 1, p. 8801, 2025. https://doi.org/10.1038/s41598-025-91065-1.10.1038/s41598-025-91065-1 ↗
41. A. Ghiasvand, S. M. Noori, W. Suksatan, J. Tomków, S. Memon, and H. A. Derazkola, “Effect of tool positioning factors on the strength of dissimilar friction stir welded joints of AA7075-T6 and AA6061-T6,” Materials, vol. 15, no. 7, p. 2463, 2022. https://doi.org/10.3390/ma15072463.10.3390/ma15072463 ↗
42. M. Chai, X. Hou, and Q. Duan, “Identification and prediction of fatigue crack growth under different stress ratios using acoustic emission data,” Int. J. Fatigue, vol. 160, no. 2, p. 106860, 2022. https://doi.org/10.1016/j.ijfatigue.2022.106860.10.1016/j.ijfatigue.2022.106860 ↗
43. J. Huang et al.., “Acoustic emission technology-based multifractal and unsupervised clustering on crack damage monitoring for low-carbon steel,” Measurement, vol. 217, no. 2, p. 113042, 2023. https://doi.org/10.1016/j.measurement.2023.113042.10.1016/j.measurement.2023.113042 ↗
44. K. Senthilkumar, M. Seeman, T. Dhamotharakannan, V. Balasubramanian, and B. Prasanna Nagasai, “Characteristics analysis and monitoring of friction stir welded dissimilar AA5083/AA6061-T6 using acoustic emission technique,” Weld. Inter., vol. 38, no. 8, pp. 556–573, 2024, https://doi.org/10.1080/09507116.2024.2376187.10.1080/09507116.2024.2376187 ↗
45. P. Rabe, A. Schiebahn, and U. Reisgen, “Force feedback-based quality monitoring of the friction stir welding process utilizing an analytic algorithm,” Weld. World, vol. 65, no. 5, pp. 845–854, 2021. https://doi.org/10.1007/s40194-020-01044-5.10.1007/s40194-020-01044-5 ↗
46. M. Chyuan Lu, S. Juinn Chiou, B. Si Kuo, and M. Zong Chen, “Analysis of acoustic emission (AE) signals for quality monitoring of laser lap micro welding,” App. Sci., vol. 11, no. 15, p. 7045, 2021, https://doi.org/10.3390/app11157045.10.3390/app11157045 ↗
47. V. Kumar, S. Ghosh, M. Kumar Parida, and K. Albert, “Application of continuous wavelet transform based on fast fourier transform for the quality analysis of arc welding process,” I. J. Sys. Assur. Eng. Manage., vol. 15, no. 3, pp. 917–930, 2023. https://doi.org/10.21203/rs.3.rs-666437/v1.10.1007/s13198-023-02178-7 ↗
48. G. N. Morscher and R. Maxwell, “Monitoring tensile fatigue crack growth and fiber failure around a notch in laminate SiC/SiC composites utilizing acoustic emission, electrical resistance, and digital image correlation,” J. Eur. Cera. Soc., vol. 39, nos. 2–3, pp. 229–239, 2019, https://doi.org/10.1016/j.jeurceramsoc.2018.08.049.10.1016/j.jeurceramsoc.2018.08.049 ↗