journal article·2025-05-26

Gas metal arc weldability of a Strenx 700MC-AISI304 dissimilar joint

Serhat Aksoy, Ramazan Kacar, Hayriye Ertek Emre, Samet Nohutcu

Materials Testing· Volume 67· Issue 5
Publisher page

Abstract

Abstract The Strenx 700MC steel is one of the HSLA steels used in the manufacturing of transportation, crane, and mining vehicles and machines due to its cold-forming abilities, strength, abrasion resistance, and weldability. The AISI304 austenitic stainless steel is also widely used in industry because of its strength, resistance to corrosion, and good weldability. In industrial applications, there is a demand for welding dissimilar steels, as well as the requirement for Strenx 700MC-AISI304 steel welded joints. Although conventional fusion welding methods are widely used in the joining of similar and dissimilar steels, MAG welding is the most widely used method in the industry due to easy adaptation to automation. The basic problem of dissimilar steels weldment is that the superior mechanical properties and corrosion resistance of the base metal of the joint are partially lost due to weld thermal cycling. For this purpose, the gas metal arc weldability of Strenx 700MC-AISI304 dissimilar steels is investigated. The mechanical properties of the weldment were determined by tensile test and hardness measurement, and their formability was detected by bending test. Additionally, the microstructure of the weldment and the fracture surfaces of the test samples were examined. Results confirm that the Strenx 700MC-AISI304 couple has been successfully joined by the GMAW method using austenitic stainless filler metal and that the strength and formability of the joint are within the acceptable range.
Source: crossref · Quality: baseline

Research context

OpenAlex topics: Welding Techniques and Residual Stresses · Metal Alloys Wear and Properties · Mechanical and Thermal Properties Analysis

SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.

Affiliations

175170 Karabük Üniversitesi , Karabuk , Türkiye

Karabük Üniversitesi Mühendislik Fakültesi , Karabuk , Türkiye

References (41)

Show source-provided references
1. P. G. Riofrío, C. Capela, and J. A. M. Ferreira, “Effect of the heat input on the mechanical properties of thin laser butt welds in an HSLA steel,” in 5th Iberian Conference on Structural Integrity, Portugal, IbCSI, 2020.
2. J. C. F. Jorge and J. L. D. Monteiro, “Influence of welding procedure and PWHT on HSLA steel weld metals,” J. Mater. Res. Technol., vol. 8, no. 1, pp. 561–571, 2019, https://doi.org/10.1016/j.jmrt.2018.05.007.10.1016/j.jmrt.2018.05.007 ↗
3. S. R. Nathan, V. Balasubramanian, G. R. Ardula, S. Tushar, M. Ivanov, and C. Rajendran, “Influence of tool plunging rate on mechanical properties and microstructure of friction stir welded DMR249A high strength low alloy (HSLA) steel butt joints,” Mater. Test., vol. 65, no. 10, pp. 1528–1538, 2023, https://doi.org/10.1515/mt-2023-0043.10.1515/mt-2023-0043 ↗
4. H. H. Wang, C. Q. Li, X. L. Wan, K. C. Nunes, Y. Li, and K. M. Wu, “Microstructural characteristics and impact toughness in YS690 MPa steel weld metal for offshore structures,” Sci. Technol. Weld. Join., vol. 22, no. 2, 2017, https://doi.org/10.1080/13621718.2016.1204774.10.1080/13621718.2016.1204774 ↗
5. L. T. Lago, M. Jambor, F. Nový, O. Bokůvka, Z. Florková, and Z. Florková, “Microstructure and residual stress analysis of Strenx 700 MC welded joint,” Prod. Eng. Arch., vol. 26, no. 2, pp. 41–44, 2020, https://doi.org/10.30657/pea.2020.26.09.10.30657/pea.2020.26.09 ↗
6. K. Aydin, M. Hıdıroğlu, and N. Kahraman, “Enhancing weld strength in high-strength steels: the role of regional preheating in RSW,” Mater. Test., vol. 66, no. 3, pp. 328–346, 2024, https://doi.org/10.1515/mt-2023-0241.10.1515/mt-2023-0241 ↗
7. S. Kozuh, M. Gojic, and L. Kosec, “Mechanical properties and microstructure of austenitic stainless steel after welding and post-weld heat treatment,” Kovove Mater.-Metal. Mater., vol. 47, no. 4, pp. 253–262, 2009.
8. M. Jayavelu, S. Kasi, V. Balasubramanian, S. Dara, and B. P. Nagasai, “Investigating microstructural evolution and wear resistance of AISI 316L stainless steel cladding deposited over mild steel using constant current GMAW and pulsed current GMAW processes,” Mater. Test., vol. 65, no. 7, pp. 1069–1084, 2023, https://doi.org/10.1515/mt-2022-0369.10.1515/mt-2022-0369 ↗
9. T. Sonar, et al.., “Effect of gas metal arc and cold metal transfer arc welding processes on microstructure and mechanical properties of AA8011-H18 alloy joints,” Mater. Test., vol. 66, no. 1, pp. 129–136, 2024, https://doi.org/10.1515/mt-2023-0208.10.1515/mt-2023-0208 ↗
10. G. Mao, et al.., “Effect of nickel contents on the microstructure and mechanical properties for low-carbon bainitic weld metals,” J. Mater. Eng. Perform., vol. 26, no. 5, pp. 2057–2071, 2017, https://doi.org/10.1007/s11665-017-2638-2.10.1007/s11665-017-2638-2 ↗
11. J. Jesus Jorge, et al.., “Mechanical properties and microstructure of SMAW welded and thermically treated HSLA-80 steel,” J. Mater. Res. Technol., vol. 7, no. 4, pp. 598–605, 2018, https://doi.org/10.1016/j.jmrt.2018.08.007.10.1016/j.jmrt.2018.08.007 ↗
12. B. De Meester, “The weldability of modern structural TMCP steels,” ISIJ Int., vol. 37, no. 6, pp. 537–551, 1997, https://doi.org/10.2355/isijinternational.37.537.10.2355/isijinternational.37.537 ↗
13. T. Satoh, H. Abe, T. Nakaoka, and Y. Hayata, “The fatigue life of the spot welded joint under a repeated load of R = −1. Comparison of mild steel and high strength steel,” Weld. World, vol. 37, no. 1, pp. 12–15, 1996.
14. C. Bo, “Choice of tool materials for punching and forming of extra- and ultra high strength steel sheet,” 3rd Int. Conf. Exhib. Des. Prod. Dies Molds, vol. 1, no. 3, pp. 1–22, 2004.
15. F. Hochhauser, W. Ernst, R. Rauch, R. Vallant, and N. Enzinger, “Influence of the soft zone on the strength of welded modern HSLA steels,” Weld. World, vol. 56, nos. 5–6, pp. 77–85, 2012, https://doi.org/10.1007/BF03321352.10.1007/BF03321352 ↗
16. H. G. Pisarski and R. E. Dolby, “The significance of softened HAZs in high strength structural steels,” Weld. World, vol. 47, nos. 5–6, pp. 32–34, 2012, https://doi.org/10.1007/BF03266387.10.1007/BF03266387 ↗
17. M. Mician, D. Harmaniak, F. Nový, J. Winczek, J. Moravec, and L. Trško, “Effect of the t8/5 cooling time on the properties of S960MC steel in the HAZ of welded joints evaluated by thermal physical simulation,” Metals, vol. 10, no. 2, p. 229, 2020, https://doi.org/10.3390/met10020229.10.3390/met10020229 ↗
18. M. Gáspár, “Effect of welding heat input on simulated HAZ areas in S960QL high strength steel,” Metals, vol. 9, no. 11, p. 1226, 2019, https://doi.org/10.3390/met9111226.10.3390/met9111226 ↗
19. F. Njock Bayock, P. Kah, B. Mvola, and P. Layus, “Effect of heat input and undermatched filler wire on the microstructure and mechanical properties of dissimilar S700MC/S960QC high-strength steels,” Metals, vol. 9, no. 8, p. 883, 2019, https://doi.org/10.3390/met9080883.10.3390/met9080883 ↗
20. W. Maurer, W. Ernst, R. Rauch, R. Vallant, and N. Enzinger, “Evaluation of the factors influencing the strength of HSLA steel weld joint with softened HAZ,” Weld. World, vol. 59, no. 6, pp. 809–822, 2015, https://doi.org/10.1007/s40194-015-0262-z.10.1007/s40194-015-0262-z ↗
21. M. Mičian, M. Frátrik, and M. Brůna, “Softening effect in the heat-affected zone of laser-welded joints of high-strength low-alloyed steels,” Weld. World, vol. 68, no. 6, pp. 1497–1514, 2024, https://doi.org/10.1007/s40194-024-01730-8.10.1007/s40194-024-01730-8 ↗
22. S. Wang, et al.., “Insights into microstructure evolution and fracture mechanisms of welded joints of high strength steel patchwork components,” J. Manuf. Processes, vol. 118, pp. 32–44, 2024, https://doi.org/10.1016/j.jmapro.2024.03.050.10.1016/j.jmapro.2024.03.050 ↗
23. D. M. Rodrigues, L. F. Menezes, A. Loureiro, and J. V. Fernandes, “Numerical study of the plastic behavior in tension of welds in high strength steels,” Int. J. Plast., vol. 20, no. 1, pp. 1–18, 2004, https://doi.org/10.1016/S0749-6419(02)00112-2.10.1016/S0749-6419(02)00112-2 ↗
24. M. Mician, M. Frátrik, and D. Kajánek, “Influence of welding parameters and filler material on the mechanical properties of HSLA SteelS960MC welded joints,” Metals, vol. 11, no. 2, p. 305, 2021, Available at: https://doi.org/10.3390/.10.3390/met11020305 ↗
25. MWA International, MWA Product Guide, 2nd ed. https://www.mwa-international.com/wp-content/uploads/2019/10/Stainless-Steels.pdf.
26. J. C. Ma, Y. Yang, W. H. Tong, Y. Fang, Y. Yu, and Z. Q. Hu, “Microstructural evolution in AISI 304 stainless steel during directional solidification and subsequent solid-state transformation,” Mater. Sci. Eng., A, vol. 444, no. 1, pp. 64–68, 2007, https://doi.org/10.1016/j.msea.2006.08.039.10.1016/j.msea.2006.08.039 ↗
27. S. H. C. Park, Y. S. Sato, H. Kokawa, K. Okamoto, S. Hirano, and M. Inagaki, “Rapid formation of the sigma phase in 304 stainless steel during friction stir welding,” Scr. Mater., vol. 49, no. 12, pp. 1175–1180, 2003, https://doi.org/10.1016/j.scriptamat.2003.08.022.10.1016/j.scriptamat.2003.08.022 ↗
28. O. Akgül and A. B. Başyiğit, “Investigating the microstructural properties and phase distributions of tig welded AISI/SAE 304L stainless steel runners used in TNT filling of ammunitions,” Int. J. Eng. Res. Develop., UMAGD, vol. 14, no. 1, pp. 228–236, 2022, https://doi.org/10.29137/umagd.1015109.10.29137/umagd.1015109 ↗
29. J. Górka, “Assessment of steel subjected to the thermomechanical control process with respect to weldability,” Metals, vol. 8, no. 169, pp. 1–17, 2018, https://doi.org/10.3390/met8030169.10.3390/met8030169 ↗
30. S. Kou, Welding Metallurgy, 3rd ed., New Jersey, Wiley, 2020, pp. 193–194.
31. C. Lippold and K. Jhon, J. D. Welding Metallurgy and Weldability of Stainless Steels, 1st ed., New Jersey, Jhon Wiley An Sons, 2005, pp. 1–376.
32. H. M. Cobb, Stainless Steels: A Steel Products Manual, 2008th ed., Warrendale, PA, USA, Assn of Iron & Steel Engineers, 2008.
33. F. Wang, et al.., “Effect of Nb addition and heat input on heat-affected zone softening in high-strength low-alloy steel,” Materials, vol. 15, no. 13, 2022, https://doi.org/10.3390/ma15134503.10.3390/ma15134503 ↗
34. M. S. Khan, M. Soleimani, A. R. H. Midawi, I. Aderibigbe, Y. N. Zhou, and E. Biro, “A review on heat affected zone softening of dual-phase steels during laser welding,” J. Manuf. Processes, vol. 102, pp. 663–684, 2023, https://doi.org/10.1016/j.jmapro.2023.07.059.10.1016/j.jmapro.2023.07.059 ↗
35. L. A. Efimenko, O. E. Kapustin, A. A. Ramus, and R. O. Ramus, “Control of softening processes in the heat-affected zone during welding of high-strength steels,” Metal Sci. Heat Treat., vol. 58, nos. 7–8, pp. 435–441, 2016, https://doi.org/10.1007/s11041-016-0031-7.10.1007/s11041-016-0031-7 ↗
36. J. Laitila and J. Larkiola, “Effect of enhanced cooling on mechanical properties of a multipass welded martensitic steel,” Weld. World, vol. 63, no. 3, pp. 637–646, 2019, https://doi.org/10.1007/s40194-018-00689-7.10.1007/s40194-018-00689-7 ↗
37. J. Laitila, J. Larkiola, and D. Porter, “Effect of heat sinks on cooling time to weld interpass temperature,” MATEC Web Conf., vol. 269, no. 6, 2019, https://doi.org/10.1051/matecconf/201926901007.10.1051/matecconf/201926901007 ↗
38. T. Węgrzyn, T. Szymczak, B. Szczucka-Lasota, and B. Łazarz, “MAG welding process with micro-jet cooling as the effective method for manufacturing joints for S700MC steel,” Metals, vol. 11, no. 2, p. 276, 2021, https://doi.org/10.3390/met11020276.10.3390/met11020276 ↗
39. J. Górka, “Assessment of the effect of laser welding on the properties and structure of TMCP steel butt joints,” Metals, vol. 13, no. 6, p. 1312, 2020, https://doi.org/10.3390/ma13061312.10.3390/ma13061312 ↗
40. J. Górka, “Assessment of the weldability of t-welded joints in 10 mm thick TMCP steel using laser beam,” Materials, vol. 11, no. 7, p. 1192, 2018, https://doi.org/10.3390/ma11071192.10.3390/ma11071192 ↗
41. H. Tervo, et al.., “Characterization of coarse- grained heat-affected zones in Al and Ti-deoxidized offshore steels,” Metals, vol. 10, no. 8, p. 1096, 2020, https://doi.org/10.3390/met10081096.10.3390/met10081096 ↗