Eliminating plasticity effects in the measurement of residual stress by using the hole-drilling method
Source abstract
Abstract
Abstract When the hole-drilling method is used to measure residual stress, plasticity effects occur if the residual stress exceeds 60 % of the yield stress. Plasticity effects result in an overestimation of the residual stress as the hole-drilling method is based on the linear elastic behavior of materials. To overcome this problem, a simplified iterative method based on an existing iterative method and using the optimizer tools of the ANSYS program is proposed in this paper. The proposed method is verified through numerical and experimental studies. The numerical case study reveals that, for the case studied, the proposed method can achieve the same accuracy as the original iterative method and has a higher convergence ability. The experimental study demonstrates that the values of the maximum principal stress calculated using the American Society of Testing Materials standard is generally greater than the true values and that the error magnitude increases with an increase in stress levels. Using the proposed method, errors are reduced for the maximum principal stress while increasing slightly for the minimum principal stress. The proposed method has a high convergence ability; for the case studied, only two or three iterations are needed to achieve acceptable accuracy.
Source: crossref · Quality: baseline
Research context
OpenAlex topics: Welding Techniques and Residual Stresses · Advanced machining processes and optimization · Non-Destructive Testing Techniques
SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.
Affiliations
Mianyang , China
References (15)
Show source-provided references
1. B. Qiang, Y. D. Li, Y. Gu, D. D. Boko-haya: Uncertainty evaluation of strain release coefficients for blind-hole method based on monte carlo simulation, Materials Testing 59 (2017), No. 7-8, pp. 630-634, DOI:10.3139/120.11105210.3139/120.111052 ↗
2. ASTM E837-13a: Standard Test Method for Determining Residual Stresses by the Hole-Drilling Strain-Gage Method, Designation: E, ASTM International, West Conshohocken, PA, USA (2013)
3. GB/T 31310-2014: Metallic Material—Determination of Residual Stress—Hole Drilling Strain Gauge Method, Standards Press of China, Beijing, P. R. China (2014)
4. S. P. Timoshenko, J. N. Goodier: Theory of Elasticity, 1st Ed., McGraw-Hill Book Company, New York, USA (1951)
5. Y. C. Lin, C. P. Chou: Error induced by local yielding around hole in hole drilling method for measuring residual stress of materials, Materials Science and Technology 11 (1995), No. 6, pp. 600-604, DOI:10.1179/mst.1995.11.6.60010.1179/mst.1995.11.6.600 ↗
6. J. Gibmeier, M. Kornmeier, B. Scholtes: Plastic deformation during application of the hole-drilling method, Materials Science Forum 347–349 (2000), pp. 131-137, DOI:10.4028/www.scientific.net/MSF.347-349.13110.4028/www.scientific.net/MSF.347-349.131 ↗
7. D. Vangi, M. Ermini: Plasticity effects in residual stress measurement by the hole drilling method, Strain 36 (2000), No. 2, pp. 55-59, OI:10.1111/j.1475-1305.200010.1111/j.1475-1305.2000.tb01174.x ↗
8. H. Y. Zhao, Y. W. Shi, Y. Pei, Y. P. Lei, Y. J. Chen: On the correction of plasticity effect at the hole edge when using the centre hole method for measuring high welding residual stress, Strain 32 (1996), No. 4, pp. 125-130, DOI:10.1111/j.1475-1305.1996.tb01017.x10.1111/j.1475-1305.1996.tb01017.x ↗
9. X. H. Zhang, H. Y. Zhao, Z. P. Cai: FEM analysis and a correction on plasticity effect at the hole edge when using the centre hole method for measuring residual stress, Chinese Journal of
10. R. Seifi, D. Salimi-Majd: Effects of plasticity on residual stresses measurement by hole drilling method, Mechanics of Materials 53(2012), pp. 72-79, DOI:10.1016/j.mechmat.2012.05.00910.1016/j.mechmat.2012.05.009 ↗
11. D. Vangi, S. Tellini: Hole-drilling strain gauge method: residual stress measurement with plasticity effects, Journal of Engineering Materials and Technology 132(2010), No.1, pp. 011003-1 – 011003-7, DOI:10.1115/1.318403010.1115/1.3184030 ↗
12. Y. Gu, Y. D. Li, Z. H. Zhou, S. B. Ren, C. Kong: Numerical simulation and measurement of welding residual stresses in orthotropic steel decks stiffened with u-shaped ribs, International Journal of Steel Structures 20(2020), No. 3, pp. 856-869, DOI:10.1007/S13296-020-00327-310.1007/s13296-020-00327-3 ↗
13. M. Kabiri: Measurement of residual stresses by the hole-drilling method: influences of transverse sensitivity of the gages and relieved-strain coefficients, Experimental Mechanics 24(1984), No. 3, pp. 252-256, DOI:10.1007/BF0232317410.1007/BF02323174 ↗
14. A. Ajovalasit: Advances in strain gauge measurement on composite materials, Strain 47(2010), No. 4, pp. 313-325 DOI:10.1111/j.1475-1305.2009.00691.x10.1111/j.1475-1305.2009.00691.x ↗
15. J. D. Lord, A. T. Fry, P. V. Grant: A UK Residual Stress Intercomparison Exercise-an Examination of the XRD and Hole Drilling Techniques, National Physical Laboratory, Teddington, Middlesex, UK (2002)10.4028/www.scientific.net/MSF.404-407.567 ↗