journal article·2013-05

Plastic deformation on worn surface of sintered diffusion alloyed Fe–Ni–Cu steel powders

A Mazahery, M O Shabani

Materials Technology· Volume 28· Issue 3
Publisher page

Abstract

To facilitate the penetration of sintered ferrous components further into key markets and applications, optimised alloy systems are required offering sufficient tribological performance at an acceptable cost. Powder metallurgy Fe−Ni−Cu is a candidate material for high performance wear resistant applications. Pin on disc reciprocating wear tests on sintered specimens under loads of 10–60 N indicate that there are several wear mechanisms operating on these steels, including oxidation and abrasion wear. Surface plastic deformation causing metallic particle detachment was also found to be significant. Porosity, which is characteristic of sintered materials, had a negative effect on ultimate tensile strength and hardness.
Source: openalex_inverted_index · Quality: baseline

Research context

OpenAlex topics: Powder Metallurgy Techniques and Materials · Advanced materials and composites · Metal Alloys Wear and Properties

SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.

References (27)

Show source-provided references
1. Madan DS · 1989 · 1 · 147
2. 10.1016/S0924-0136(03)00421-710.1016/S0924-0136(03)00421-7 ↗
3. 10.1179/pom.2000.43.1.5710.1179/pom.2000.43.1.57 ↗
4. 10.1016/j.actamat.2004.06.01810.1016/j.actamat.2004.06.018 ↗
5. 10.1016/0043-1648(77)90081-310.1016/0043-1648(77)90081-3 ↗
6. 10.1179/174329009X40973210.1179/174329009X409732 ↗
7. 10.1016/0043-1648(94)90264-X10.1016/0043-1648(94)90264-X ↗
8. 10.1016/0043-1648(86)90035-910.1016/0043-1648(86)90035-9 ↗
9. 10.1016/S0043-1648(98)00265-810.1016/S0043-1648(98)00265-8 ↗
10. 10.1179/00325890166641910.1179/003258901666419 ↗
11. 10.1179/00325890422501554510.1179/003258904225015545 ↗
12. 10.1179/00325899966557610.1179/003258999665576 ↗
13. 10.1016/j.scriptamat.2004.09.03210.1016/j.scriptamat.2004.09.032 ↗
14. 10.1016/j.matdes.2006.05.02210.1016/j.matdes.2006.05.022 ↗
15. 10.1179/174328408X27023910.1179/174328408X270239 ↗
16. 10.1016/0043-1648(94)90097-310.1016/0043-1648(94)90097-3 ↗
17. 10.1016/S0026-0657(02)85078-010.1016/S0026-0657(02)85078-0 ↗
18. Bocchini GF · Int. J. Powder Metall. · 1986 · 22 · 185
19. Klar E, Samal PK: ‘Powder metallurgy stainless steels’, in ‘Powder metal technologies and applications’, Vol. 7; 1994, Materials Park, OH, ASM International.
20. Hadrboletz A · Int. Mater. Rev. · 1997 · 1 · 44
21. Bergmark A: ‘Microstructure enhancement for fatigue improvement’, Proc. EURO PM2003 Conf., Valencia, Spain, October 2003, EPMA.
22. Gzyryca E · 1985 · 8 · 363
23. Saritas S, Causton R, James WB, Lawley A: ‘Effect of microstructural in homogenities on the fatigue crack growth response of a prealloyed and two hybrid PM steels’, Proc. World Cong. on ‘Powder metallurgy and particular material’, Orlando, FL, June 2002, 21.
24. Alzati L, Bergmark A, Andersson J: ‘Fatigue performance of PM steel in as-sintered state’, Proc. PMAI Conf., Mumbai, India, February 2005, PMAI2005.
25. 10.1016/S0921-5093(98)00846-610.1016/S0921-5093(98)00846-6 ↗
26. 10.1115/1.362505110.1115/1.3625051 ↗
27. Hamilton GM · Proc. Inst. Mech. Eng. · 1983 · 197 · 53