Lateral resolution enhancement in low-cost DLP 3D printing via integrated optical focusing and collimation
Source abstract
Abstract
Abstract Digital light processing (DLP)-based additive manufacturing systems offer high printing speeds; however, their resolution is inherently limited in low-cost configurations due to projector pixel size, optical divergence, and angular light incidence on the photopolymer surface. In this study, a compact optical module consisting of focusing and collimation lenses was integrated between a commercial DLP projector and the photopolymer vat to address these limitations. The proposed system concentrates the projected light onto a reduced exposure area and enforces near-normal light incidence, improving voxel definition and suppressing angular curing artifacts. Benchmark geometries were fabricated with and without the optical module using a single daylight-sensitive photopolymer resin. The results show that the effective pixel size was reduced from approximately 165–170 μm to 43–46 μm. In addition, the increased irradiance enabled a reduction in layer exposure time from 2,500 to 100 ms, resulting in an overall printing time reduction of about 30%. Although the optical configuration limits the build area, it provides a purely physical and effective alternative to software-based super-resolution approaches for low-cost DLP systems.
Source: crossref · Quality: baseline
Research context
OpenAlex topics: Additive Manufacturing and 3D Printing Technologies · Advanced Optical Imaging Technologies · Advanced optical system design
SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.
Affiliations
Mechanical Engineering, Faculty of Engineering and Architecture, Kahramanmaras Sutcu Imam University , Kahramanmaras , Turkiye
References (21)
Show source-provided references
1. Wong, K.V., Hernandez, A., A review of additive manufacturing. ISRN Mech. Eng., 2012; 2012(1): 208760. 10.5402/2012/20876010.5402/2012/208760 ↗
2. Gibson, I., Rosen, D., Stucker, B., Additive manufacturing technologies: 3D printing, rapid prototyping, and direct digital manufacturing. Irradiance and Exposure, New York: Springer, 2015, pp. 75–8110.1007/978-1-4939-2113-3 ↗
3. Rooney, K., Dong, Y., Pramanik, A., Basak, A.K., Additive manufacturing in Australian small to medium enterprises: Vat polymerisation techniques, case study and pathways to Industry 4.0 competitiveness. J. Manuf. Mater. Process, 2023; 7(5): 168. 10.3390/jmmp705016810.3390/jmmp7050168 ↗
4. Salgado, H., Gomes, A.T., Duarte, A.S., Ferreira, J.M., Fernandes, C., Figueiral, M.H., et al., Antimicrobial activity of a 3D-printed polymethylmethacrylate dental resin enhanced with graphene. Biomedicines, 2022; 10(10): 260710.3390/biomedicines10102607 ↗
5. García-Gil, I., Rodríguez Alonso, V., López Suárez, C., Mosaddad, S.A., Peláez, J., Suárez, M.J., Influence of the print orientation and cast thickness on the accuracy of DLP master casts for fixed dental prostheses. BMC Oral Health, 2025, 25(1): 532. 10.1186/s12903-025-05944-010.1186/s12903-025-05944-0 ↗
6. Jindal, P., Juneja, M., Bajaj, D., Siena, F.L., Breedon, P., Effects of post-curing conditions on mechanical properties of 3D printed clear dental aligners. Rapid Prototyp. J., 2020, 26(8): 1337–1344. 10.1108/RPJ-04-2019-011810.1108/RPJ-04-2019-0118 ↗
7. Mastroianni, L., Russo, V., Eränen, K., Di Serio, M., Murzin, D.Y., Salmi, T., Towards unconstrained catalyst shaping: High-accuracy DLP printing of porous γ-Al₂O₃-based catalysts. Catal. Sci, Technol., 2024; 14(5): 1336–1348. 10.1039/D3CY01592K10.1039/D3CY01592K ↗
8. Başcı, Ü.G., Yamanoğlu, R., Havuz fotopolimerizasyonu (HFP) ile eklemeli imalat. DÜBİTED, 2022; 10(2): 914–92810.29130/dubited.922415 ↗
9. Monk, D.W., Gail, R.O., The digital micromirror device for projection display. Microelectron. Eng., 1995; 27: 489–49310.1016/0167-9317(94)00151-J ↗
10. Chaudhary, R., Fabbri, P., Leoni, E., Mazzanti, F., Akbari, R., Antonini, C., Additive manufacturing by digital light processing: A review. Prog. Addit. Manuf., 2023; 8: 331–35110.1007/s40964-022-00336-0 ↗
11. Kang, H.W., Park, J.H., Cho, D.W., A pixel-based solidification model for projection-based stereolithography technology. Sens. Actuators A: Phys., 2012; 178: 223–22910.1016/j.sna.2012.01.016 ↗
12. Yu, Z., Li, X., Zuo, T., Wang, Q., Wang, H., Liu, Z., High-accuracy DLP 3D printing of closed microfluidic channels based on a mask option strategy. Int. J. Adv. Manuf. Technol., 2023; 127(9): 4001–4012. 10.1007/s00170-023-11769-410.1007/s00170-023-11769-4 ↗
13. Huang, J., Zhang, B., Xiao, J., Zhang, Q., An approach to improve the resolution of DLP 3D printing by parallel mechanism. Appl. Sci., 2022; 12(24): 12905. 10.3390/app12241290510.3390/app122412905 ↗
14. Li, Y., Mao, Q., Yin, J., Wang, Y., Fu, J., Huang, Y., Theoretical prediction and experimental validation of the digital light processing (DLP) working curve for photocurable materials. Addit. Manuf., 2021; 37: 10171610.1016/j.addma.2020.101716 ↗
15. Rade, P.P., Swami, S., Pawane, V., Hawaldar, R., Giramkar, V., Joseph, S., et al., Effect of functionality of diluents on digital light processing (DLP)-based three-dimensional printing of UV-curable epoxy acrylate resin. Polym. Eng. Sci., 2024; 64(5): 2202–221310.1002/pen.26686 ↗
16. Valentinčič, J., Peroša, M., Jerman, M., Sabotin, I., Lebar, A., Low-cost printer for DLP stereolithography. Stroj. Vestn./J. Mech. Eng., 2017; 63(10): 559–56610.5545/sv-jme.2017.4591 ↗
17. Huang, J., Cai, J., Huangfu, C., Li, S., Chen, G., Yun, H., et al., A scalable digital light processing 3D printing method. Micromachines, 2024; 15: 1298. 10.3390/mi1511129810.3390/mi15111298 ↗
18. Montgomery, S.M., Demoly, F., Zhou, K., Qi, H.J., Pixel-level grayscale manipulation to improve accuracy in digital light processing 3D printing. Adv. Funct. Mater., 2022; 32(31): 2202945. 10.1002/adfm.20220294510.1002/adfm.202213252 ↗
19. Sekmen, K., Rehbein, T., Johlitz, M., Lion, A., Constantinescu, A., Thermal analysis and shrinkage characterization of photopolymers for DLP additive manufacturing processes. Contin. Mech. Thermodyn., 2024; 36(2): 351–36810.1007/s00161-022-01137-0 ↗
20. Valentinčič, J., Sevšek, L., Prijatelj, M., Sabotin, I., Jerman, M., Lebar, A., Towards production of microfeatures on a custom-made stereolithographic DLP printer. Proceedings in Manufacturing Systems, 2018
21. Yan, H., Wang, Z., Xu, Z., Wang, Z., Wu, Z., Lyu, R., Research on image super-resolution reconstruction mechanism based on convolutional neural network. In Proceedings of the 4th International Conference on Artificial Intelligence, Automation and High Performance Computing (AAHPC 2024), 2024, pp. 558–563. 10.1145/3690931.369095610.1145/3690931.3690956 ↗