journal article·2025-09-01

A review of sheet warm forming methods for high-strength 7xxx aluminum alloys

Mateusz Skwarski

Materials Science-Poland· Volume 43· Issue 3
Publisher page

Abstract

Abstract The article presents an overview of the warm forming process used to form 7xxx alloy sheets. The literature review covers the characteristics of alloys tested during forming at elevated temperatures: AA7075, AA7020, and a non-commercial alloy with a lower chromium content, higher zirconium content, and higher zinc-to-magnesium ratio than commercial alloys. A diagram of the forming process is presented, taking into account the individual stages and the most important parameters of heat treatment and deformation. An analysis was carried out of the results published to date in the field of basic research, such as tensile tests of alloys in the temperature range of 20–300°C, limiting dome high and limiting drawing ratio tests in the temperature range of 20–260°C, and tests of forming blanks such as a bracket, U-profile, lower part of a B-pillar, and B-pillar. Based on an extensive literature review, it can be concluded that warm stamping with accelerated heating allows for achieving at least 90% of the original strength of the AA7075 alloy. The use of a paint baking process (heat treatment at 180°C for 30 min) after stamping can contribute to a final product strength of up to 85–90% of the strength of the alloy in the T6 state.
Source: crossref · Quality: baseline

Research context

SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.

Affiliations

Department of Metal Forming, Welding and Metrology, Faculty of Mechanical Engineering, Wroclaw University of Science and Technology , Wyspiańskiego 27, 50-370 , Wroclaw , Poland

Center for Materials Science and Metal Forming, Wroclaw University of Science and Technology , Lukasiewicza 5, 50-371 , Wroclaw , Poland

References (22)

Show source-provided references
1. WorldAutoSteel, Life Cycle Assessment Case Study SuperLIGHT-Car (SLC), (2011) 4. http://www.worldautosteel.org/download_files/CaseStudies/2LCACaseStudy_SuperLightCar_20110323.pdf
2. Gądek, T., Majewski, M., Research on the effect of temperature increase during flow forming without cooling on 6060 aluminum alloy, Mater. Sci. Pol., 2023, 41: 74–84. 10.2478/msp-2023-003310.2478/msp-2023-0033 ↗
3. Lachowicz, M.M., Metallurgical aspects of the corrosion resistance of 7000 series aluminum alloys – a review, Mater. Sci. Pol., 2023, 41: 159–180. 10.2478/msp-2023-004110.2478/msp-2023-0041 ↗
4. Zwolak, M., Sliwa, R., Analysis of the influence of dies geometry on the process extrusion force and properties of the extrudate obtained in the process of cold extrusion of 7075 aluminum alloy by the KOBO method, Mater. Sci. Pol., 2024, 42: 92–106. 10.2478/msp-2024-000810.2478/msp-2024-0008 ↗
5. Zhou, B., Liu, B., Zhang, S., The advancement of 7xxx series aluminum alloys for aircraft structures: A review, Metals (Basel), 2021, 11: 13–20. 10.3390/met1105071810.3390/met11050718 ↗
6. Hirsch, J., Aluminium in innovative light-weight car design, Mater. Trans., 2011, 52: 818–824. 10.2320/matertrans.L-MZ20113210.2320/matertrans.L-MZ201132 ↗
7. Anbalagan, K., Duraisamy, V., Loganathan, R.V., Sam, P.P., Influence of cerium oxide nanoparticles on the tribological behavior of AA8090 aluminum alloy composites for aero, military, and marine industrial applications, Mater. Sci. Pol., 2024, 42: 101–112. 10.2478/msp-2024-004810.2478/msp-2024-0048 ↗
8. Scharifi, E., Yardley, V.A., Weidig, U., Szegda, D., Lin, J., Steinhoff, K., Hot sheet metal forming strategies for high-strength aluminum alloys: a review – fundamentals and applications, Adv. Eng. Mater., 2023, 25: 8–10. 10.1002/adem.20230014110.1002/adem.202300141 ↗
9. Noder, J., George, R., Butcher, C., Worswick, M.J., Friction characterization and application to warm forming of a high strength 7000-series aluminum sheet, J. Mater. Process. Technol., 2021, 293: 117066. 10.1016/j.jmatprotec.2021.11706610.1016/j.jmatprotec.2021.117066 ↗
10. Kumar, M., Sotirov, N., Chimani, C.M., Investigations on warm forming of AW-7020-T6 alloy sheet, J. Mater. Process. Technol., 2014, 214: 1769–1776. 10.1016/j.jmatprotec.2014.03.02410.1016/j.jmatprotec.2014.03.024 ↗
11. Wang, H., Luo, Y.B., Friedman, P., Chen, M.H., Gao, L., Warm forming behavior of high strength aluminum alloy AA7075, Trans. Nonferrous Met. Soc. China (Engl. Ed.), 2012, 22: 1–7. 10.1016/S1003-6326(11)61131-X10.1016/S1003-6326(11)61131-X ↗
12. Lee, M.Y., Sohn, S.M., Kang, C.Y., Suh, D.W., Lee, S., Effects of pre-treatment conditions on warm hydroformability of 7075 aluminum tubes, J. Mater. Process. Technol., 2004, 155: 1337–1343. 10.1016/j.jmatprotec.2004.04.20010.1016/j.jmatprotec.2004.04.200 ↗
13. Huo, W., Hou, L., Zhang, Y., Zhang, J., Warm formability and post-forming microstructure/property of high-strength AA 7075-T6 Al alloy, Mater. Sci. Eng. A., 2016, 675: 44–54. 10.1016/j.msea.2016.08.05410.1016/j.msea.2016.08.054 ↗
14. Polak, S., Kaczyński, P., Gronostajski, Z., Jaskiewicz, K., Krawczyk, J., Skwarski, M., et al., Warm forming of 7075 aluminum alloys, Procedia Eng., 2017, 207: 2399–2404. 10.1016/j.proeng.2017.10.101510.1016/j.proeng.2017.10.1015 ↗
15. Zhang, W.P., Li, H.H., Hu, Z.L., Hua, L., Investigation on the deformation behavior and post-formed microstructure/properties of AA7075-T6 alloy under pre-hardened hot forming process, Mater. Sci. Eng. A., 2020, 792: 139749. 10.1016/j.msea.2020.13974910.1016/j.msea.2020.139749 ↗
16. Behrens, B.A., Nürnberger, F., Bonk, C., Hübner, S., Behrens, S., Vogt, H., Influences on the formability and mechanical properties of 7000-aluminum alloys in hot and warm forming, J. Phys. Conf. Ser., 2017, 896: 5–8. 10.1088/1742-6596/896/1/01200410.1088/1742-6596/896/1/012004 ↗
17. Jaśkiewicz, K., Skwarski, M., Kaczyński, P., Gronostajski, Z., Polak, S., Trzpis, P., Warm sheet metal forming of energy-absorbing elements made 7075 aluminum alloy in the hardened state T6, Int. J. Adv. Manuf. Technol., 2022, 119: 3157–3179. 10.1007/s00170-021-08549-310.1007/s00170-021-08549-3 ↗
18. Gronostajski, Z., Polak, S., Jaśkiewicz, K., Kaczyńskia, P., Skwarski, M., Krawczyk, J., et al., Properties of B-pillar made of aluminium 7075 in warm forming process, Procedia Manuf., 2019, 27: 98–103. 10.1016/j.promfg.2018.12.05010.1016/j.promfg.2018.12.050 ↗
19. Sun, L., Zhang, Z., Song, Z., Ren, M., Jia, H., Feasibility study on contact heating warm forming of 7075 ‑ T6 aluminum alloy, Arch. Civ. Mech. Eng., 2023, 23: 1–8. 10.1007/s43452-023-00749-w10.1007/s43452-023-00749-w ↗
20. Ma, H., Sun, L., Zhang, Z., Jia, H., Ren, M., Study on process parameters optimization of 7075-T6 aluminum alloy under contact heating, Arch. Civ. Mech. Eng., 2024, 24: 1–10. 10.1007/s43452-024-00913-w10.1007/s43452-024-00913-w ↗
21. Deng, L., Wang, X., Jin, J., Xia, L., Springback and hardness of aluminum alloy sheet part manufactured by warm forming process using non-isothermal dies, Procedia Eng., 2017, 207: 2388–2393. 10.1016/j.proeng.2017.10.101310.1016/j.proeng.2017.10.1013 ↗
22. Wang, N., Ilinich, A., Chen, M., Luckey, G., D’Amours, G., A comparison study on forming limit prediction methods for hot stamping of 7075 aluminum sheet, Int. J. Mech. Sci., 2019, 151: 444–460. 10.1016/j.ijmecsci.2018.12.00210.1016/j.ijmecsci.2018.12.002 ↗