Sliding elements made from biodegradable plastic – friction and wear of poly(lactic acid) compared to polyamide 6
Source abstract
Abstract
Abstract Plastic sliding components are environmentally friendly, as they do not require the use of grease or oil, and much of this type of substance ends up in the environment as a result of accidents or spills. Unfortunately, at the end of the product lifecycle, plastic sliding component is a very bothersome waste. In addition, the products of wear are a source of microplastics entering the environment. Biodegradable polymers are the answer to waste problem. The aim of this article is to assess whether poly(lactic acid) (PLA), one of the most popular biodegradable polymers, has a chance to be used in sliding components. Since only a few reports on PLA friction and wear were found in the literature, a wide range of tests were carried out. The results obtained for PLA were compared to those obtained for polyamide 6 (PA6), which is a non-biodegradable material but is widely used in sliding components. The research showed that the biggest problem for PLA is its low temperature resistance. As a result, PLA can work with steel at significantly lower pressures and velocities than other plastics. At velocity of 1.0 m/s, PLA could cooperate with steel at a maximum pressure of 0.3 MPa, while PA6 could do it even at 2.0 MPa (at a pressure almost seven times higher). The wear and friction coefficient for PLA are also high (wear was 195 µm/km and coefficient of friction was 0.54 when velocity was 0.5 m/s and pressure was 0.7 MPa), and PLA also wore about four times more than PA6 during the abrasive wear test. When looking for a way to increase the ability of PLA to work at higher velocities and pressures, it is worth investigating annealed PLA, PLA blends with other biodegradable polymers, or PLA with the addition of hard fillers such as natural fibres or carbonates.
Source: crossref · Quality: baseline
Research context
OpenAlex topics: biodegradable polymer synthesis and properties · Tribology and Wear Analysis · Polymer Foaming and Composites
SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.
Affiliations
Department of Fundamentals of Machine Design and Mechatronic Systems, Faculty of Mechanical Engineering, Wroclaw University of Science and Technology, Politechnika Wroclawska , Wroclaw , Poland
References (49)
Show source-provided references
1. Madanhire, I., Mbohwa, C., Lubricant additive impacts on human health and the environment, In: Mitigating Environmental Impact of Petroleum Lubricants, Springer International Publishing, Cham, 2016. p. 17–34. 10.1007/978-3-319-31358-0_210.1007/978-3-319-31358-0_2 ↗
2. Nayanathara Thathsarani Pilapitiya, P.G.C., Ratnayake, A.S., The world of plastic waste: A review, Clean. Mater., 2024, 11: 100220. 10.1016/j.clema.2024.10022010.1016/j.clema.2024.100220 ↗
3. Winiarska, E., Jutel, M., Zemelka-Wiacek, M., The potential impact of nano- and microplastics on human health: Understanding human health risks, Environ. Res., 2024, 251: 118535. 10.1016/j.envres.2024.11853510.1016/j.envres.2024.118535 ↗
4. Prata, J.C., da Costa, J.P., Lopes, I., Andrady, A.L., Duarte, A.C., Rocha-Santos, T., A One Health perspective of the impacts of microplastics on animal, human and environmental health, Sci. Total. Environ., 2021, 777: 146094. 10.1016/j.scitotenv.2021.14609410.1016/j.scitotenv.2021.146094 ↗
5. Li, N., Yang, H., Dong, Y., Wei, B., Liang, L., Yun, X., et al., Prevalence and implications of microplastic contaminants in general human seminal fluid: A Raman spectroscopic study, Sci. Total. Environ., 2024, 937: 173522. 10.1016/j.scitotenv.2024.17352210.1016/j.scitotenv.2024.173522 ↗
6. Gaspar, L., Bartman, S., Coppotelli, G., Ross, J.M., Acute exposure to microplastics induced changes in behavior and inflammation in young and old mice, Int. J. Mol. Sci., 2023, 24(15): 12308. 10.3390/ijms24151230810.3390/ijms241512308 ↗
7. Garcia, M.M., Romero, A.S., Merkley, S.D., Meyer-Hagen, J.L., Forbes, C., Hayek, E. E., et al., In vivo tissue distribution of polystyrene or mixed polymer microspheres and metabolomic analysis after oral exposure in mice, Environ. Health Perspect., 2024, 132(4):047005-1–14. 10.1289/EHP1343510.1289/EHP13435 ↗
8. RameshKumar, S., Shaiju, P., O’Connor, K.E., Bio-based and biodegradable polymers – State-of-the-art, challenges and emerging trends, Curr. Opin. Green. Sustain. Chem., 2020, 21: 75–81. 10.1016/j.cogsc.2019.12.00510.1016/j.cogsc.2019.12.005 ↗
9. Elvers, D., Song, C.H., Steinbüchel, A., Leker, J., Technology trends in biodegradable polymers: Evidence from patent analysis, Polym. Rev., 2016, 56(4): 584–606. 10.1080/15583724.2015.112591810.1080/15583724.2015.1125918 ↗
10. Farah, S., Anderson, D.G., Langer, R., Physical and mechanical properties of PLA, and their functions in widespread applications – A comprehensive review, Adv. Drug. Delivery Rev., 2016, 107: 367–392. 10.1016/j.addr.2016.06.01210.1016/j.addr.2016.06.012 ↗
11. Madhavan Nampoothiri, K., Nair, N.R., John, R.P., An overview of the recent developments in polylactide (PLA) research, Bioresour. Technol., 2010, 101(22): 8493–8501. 10.1016/j.biortech.2010.05.09210.1016/j.biortech.2010.05.092 ↗
12. Napper, I.E., Thompson, R.C., Environmental deterioration of biodegradable, oxo-biodegradable, compostable, and conventional plastic carrier bags in the sea, soil, and open-air over a 3-year period, Environ. Sci. Technol., 2019, 53(9): 4775–4783. 10.1021/acs.est.8b0698410.1021/acs.est.8b06984 ↗
13. binti Jalani, J.C., Arshad, Z.I.M., PLA degradation and PLA-degrading bacteria: A mini-review, Key Eng. Mater., 2022, 932: 103–110. 10.4028/p-4ic76p10.4028/p-4ic76p ↗
14. Shekhar, N., Mondal, A., Synthesis, properties, environmental degradation, processing, and applications of Polylactic Acid (PLA): an overview, Polym. Bull., 2024, 81: 11421–11457. 10.1007/s00289-024-05252-710.1007/s00289-024-05252-7 ↗
15. Borelbach, P., Kopitzky, R., Dahringer, J., Gutmann, P., Degradation behavior of biodegradable man-made fibers in natural soil and in compost, Polymers, 2023, 15(13): 2959. 10.3390/polym1513295910.3390/polym15132959 ↗
16. Rudnik, E., Briassoulis, D., Comparative biodegradation in soil behaviour of two biodegradable polymers based on renewable resources, J. Polym. Environ., 2011, 19(1): 18–39. 10.1007/s10924-010-0243-710.1007/s10924-010-0243-7 ↗
17. Tsuji, H., Suzuyoshi, K., Environmental degradation of biodegradable polyesters 1. Poly(ε-caprolactone), poly[(R)-3-hydroxybutyrate], and poly(L-lactide) films in controlled static seawater, Polym. Degrad. Stab., 2002, 75(2): 347–355. 10.1016/S0141-3910(01)00240-310.1016/S0141-3910(01)00240-3 ↗
18. Tsuji, H., Suzuyoshi, K., Environmental degradation of biodegradable polyesters 2. Poly(ε-caprolactone), poly[(R)-3-hydroxybutyrate], and poly(L-lactide) films in natural dynamic seawater, Polym. Degrad. Stab., 2002, 75(2): 357–365. 10.1016/S0141-3910(01)00239-710.1016/S0141-3910(01)00239-7 ↗
19. Le Duigou, A., Davies, P., Baley, C., Seawater ageing of flax/poly(lactic acid) biocomposites, Polym. Degrad. Stab., 2009, 94(7): 1151–1162. 10.1016/j.polymdegradstab.2009.03.02510.1016/j.polymdegradstab.2009.03.025 ↗
20. Şirin, Ş., Aslan, E., Akincioğlu, G., Effects of 3D-printed PLA material with different filling densities on coefficient of friction performance, Rapid Prototyp. J., 2023, 29(1): 157–165. 10.1108/RPJ-03-2022-008110.1108/RPJ-03-2022-0081 ↗
21. Zhiani Hervan, S., Altınkaynak, A., Parlar, Z., Hardness, friction and wear characteristics of 3D-printed PLA polymer, Proc. Inst. Mech. Eng., Part. J: J. Eng. Tribol., 2021, 235(8): 1590–1598. 10.1177/135065012096640710.1177/1350650120966407 ↗
22. Zhang, P., Hu, Z., Xie, H., Lee, G.H., Lee, C.H., Friction and wear characteristics of polylactic acid (PLA) for 3D printing under reciprocating sliding condition, Ind. Lubrication Tribol., 2019, 72(4): 533–539. 10.1108/ILT-11-2016-028010.1108/ILT-11-2016-0280 ↗
23. Frunzaverde, D., Cojocaru, V., Ciubotariu, C.R., Miclosina, C.O., Ardeljan, D.D., Ignat, E.F., et al., The influence of the printing temperature and the filament color on the dimensional accuracy, tensile strength, and friction performance of FFF-printed PLA specimens, Polymers, 2022, 14(10): 1978. 10.3390/polym1410197810.3390/polym14101978 ↗
24. Zainal, M.A., Ismail, K.I., Yap, T.C., Tribological properties of PLA 3D printed at different extrusion temperature, J. Phys.: Conf. Ser., 2023, 2542(1): 012001. 10.1088/1742-6596/2542/1/01200110.1088/1742-6596/2542/1/012001 ↗
25. Ramadan, M.A, Sabour, H.A., Eman, E.S., Tribological properties of 3D printed polymers: PCL, ABS, PLA and Co polyester. Tribol. Ind., 2023;45(1): 161–167. 10.24874/ti.1410.11.22.0210.24874/ti.1410.11.22.02 ↗
26. Chisiu, G., Stoica, N.A., Stoica, A.M., Friction behavior of 3D-printed polymeric materials used in sliding systems, Materiale Plastice, 2021, 58(1): 176–185. 10.37358/MP.21.1.545710.37358/MP.21.1.5457 ↗
27. Mathurosemontri, S., Thumsorn, S., Nagai, S., Hamada, H., Investigation of friction and wear behavior of polyoxymethylene/poly(lactic acid) blends, Key Eng. Mater., 2017, 728: 229–234. 10.4028/www.scientific.net/KEM.728.22910.4028/www.scientific.net/KEM.728.229 ↗
28. Fekete, G., Numerical wear analysis of a PLA-made spur gear pair as a function of friction coefficient and temperature, Coatings, 2021, 11(4): 409. 10.3390/coatings1104040910.3390/coatings11040409 ↗
29. Technical Data Sheet Plexiwire PLA. https://www.plexiwire.com/wp-content/uploads/2023/08/TDS-Plexiwire-filament-PLA.pdf.
30. Technical Data Sheet Plexiwire Nylon PA6. https://www.plexiwire.com/wp-content/uploads/2023/08/TDS-Plexiwire-filament-Nylon-PA6.pdf.
31. Jian-di, J., Kun, Z., Chong-yang, L., Guo-zhang, W., Thermal expansion behavior of aliphatic polyamides, Acta Polymerica Sin., 2013, (2): 255–262. 10.3724/SP.J.1105.2013.1224110.3724/SP.J.1105.2013.12241 ↗
32. Rădulescu, B., Mihalache, A.M., Hrițuc, A., Rădulescu, M., Slătineanu, L., Munteanu, A., et al., Thermal expansion of plastics used for 3D printing, Polymers, 2022, 14(15): 3061. 10.3390/polym1415306110.3390/polym14153061 ↗
33. Wieleba, W., Przegląd polimerów termoplastycznych stosowanych na ślizgowe elementy maszyn, In: Bezobsługowe łożyska ślizgowe z polimerów termoplastycznych, Oficyna Wydawnicza Politechniki Wrocławskiej, Wrocław, 2013. p. 11–47
34. Rajesh, J.J., Bijwe, J., Tewari, U., Abrasive wear performance of various polyamides, Wear, 2002, 252(9–10): 769–776. 10.1016/S0043-1648(02)00039-X10.1016/S0043-1648(02)00039-X ↗
35. Hosseini, M., Mashtizadeh, A.R., Taghizadeh Tabrizi, A., Hossein, A., Effect of lead and molybdenum disulfide additives on wear resistance and physical properties of copper–graphite composite, Mater. Sci.-Poland, 2024, 42(4): 148–161. 10.2478/msp-2024-004610.2478/msp-2024-0046 ↗
36. Kannan, P.R., Thanigaivelan, R., Thiraviam, R., Pradeep Kumar, K., Performance studies on hybrid nano-metal matrix composites for wear and surface quality, Mater. Sci.-Poland, 2023, 41(2): 288–300. 10.2478/msp-2023-002010.2478/msp-2023-0020 ↗
37. Xia, R., Zhang, K., Shu, F., Zhang, X., Yan, L., Li, C., Effects of B content on wear and corrosion resistance of laser-cladded Co-based alloy coatings, Mater. Sci.-Poland, 2024, 41(4): 13–23. 10.2478/msp-2023-004010.2478/msp-2023-0040 ↗
38. Przekop, R.E., Kujawa, M., Pawlak, W., Dobrosielska, M., Sztorch, B., Wieleba, W., Graphite modified polylactide (PLA) for 3D printed (FDM/FFF) sliding elements, Polymers, 2020, 12(6): 1250. 10.3390/polym1206125010.3390/polym12061250 ↗
39. Kujawa, M., Przekop, R., Pawlak, W., Widuch, A., Hanszke, J., The influence of graphite addition on tribological properties of polylactide (PLA), Tribologia, 2023, 304(2): 45–54. 10.5604/01.3001.0053.612310.5604/01.3001.0053.6123 ↗
40. Kujawa, M., Głowacka, J., Pawlak, W., Sztorch, B., Pakuła, D., Frydrych, M., et al., Molybdenum disulphide modified polylactide for 3D printed (FDM/FFF) filaments, Polymers, 2023, 15(10): 2236. 10.3390/polym1510223610.3390/polym15102236 ↗
41. Santo, J., Pradik, V., Kalakoti, S., Saravanan, P., Penumakala, P.K., Effect of composite processing technique on tribological properties of 3D printed PLA-graphene composites, Tribol. Int., 2024, 198: 109895. 10.1016/j.triboint.2024.10989510.1016/j.triboint.2024.109895 ↗
42. Li, X., Lin, Y., Liu, M., Meng, L., Li, C., A review of research and application of polylactic acid composites, J. Appl. Polym. Sci., 2023, 140(7): e53477-1–22. 10.1002/app.5347710.1002/app.53477 ↗
43. Przekop, R.E., Gabriel, E., Dobrosielska, M., Martyła, A., Jakubowska, P., Głowacka, J., et al., The 3D-printed (FDM/FFF) biocomposites based on polylactide and carbonate lake sediments – towards a circular economy, Polymers, 2023, 15(13): 2817. 10.3390/polym1513281710.3390/polym15132817 ↗
44. Suder, J., Bobovsky, Z., Mlotek, J., Vocetka, M., Zeman, Z., Safar, M., Experimental analysis of temperature resistance of 3D printed PLA components, MM Sci. J., 2021, 2021(1): 4322–4327. 10.17973/MMSJ.2021_03_202100410.17973/MMSJ.2021_03_2021004 ↗
45. Sun, S., Meng, X., Xie, Y., Wang, J., Ma, X., Wang, N., et al., Wire-based friction stir additive manufacturing enables enhanced interlayer bonding in aluminum-matrix composites, J. Manuf. Process., 2025, 153: 1–15. 10.1016/j.jmapro.2025.08.07810.1016/j.jmapro.2025.08.078 ↗
46. Zhang, Z., Wan, L., Meng, X., Xie, Y., Tian, H., Mao, D., et al., Robotic wire-based friction stir additive manufacturing, Addit. Manuf., 2024, 88: 104261. 10.1016/j.addma.2024.10426110.1016/j.addma.2024.104261 ↗
47. Hassan, A., Pedapati, S.R., Awang, M., Soomro, I.A., A comprehensive review of friction stir additive manufacturing (FSAM) of non-ferrous alloys, Materials, 2023, 16(7): 2723. 10.3390/ma1607272310.3390/ma16072723 ↗
48. Derazkola, H.A., Khodabakhshi, F., Simchi, A., Evaluation of a polymer-steel laminated sheet composite structure produced by friction stir additive manufacturing (FSAM) technology, Polym. Test., 2020, 90: 106690. 10.1016/j.polymertesting.2020.10669010.1016/j.polymertesting.2020.106690 ↗
49. Tagimalek, H., Mahmoodi, M., Evaluation of wear test on functionally graded metal-polymer tri-laminate composite interfaces of cooling-assisted friction stir additive manufacturing, J. Adv. Join. Process., 2023, 8: 100166. 10.1016/j.jajp.2023.10016610.1016/j.jajp.2023.100166 ↗