journal article·2020-12-01Open access

Dynamic failure mechanism of copper foil in laser dynamic flexible forming

Zongbao Shen, Lei Zhang, Pin Li, Kai Liu, Youyu Lin, Guoyang Zhou, Yang Wang, Jindian Zhang, Huixia Liu, Xiao Wang

Materials Science-Poland· Volume 38· Issue 4

Abstract

Abstract Laser dynamic flexible forming (LDFF) is a novel high velocity forming (HVF) technology, in which the foil metal is loaded by laser shock wave. Strain localization is readily to occur around the bulge edge, which will result in the ultimate dynamic failure. In this work, the microstructures before and after dynamic fracture are characterized by transmission electron microscopy (TEM) to investigate the dynamic failure mechanism. The plastic deformation regions of copper foil are composed of shock compression, strain localization and bulge. Microstructure refinement was observed in three different plastic deformation regions, particularly, dynamic recrystallization (DRX) occurs in the strain localization and bulge regions. In bulge region, extremely thin secondary twins in the twin/matrix (T/M) lamellae are formed. The microstructure features in the strain localization region show that superplastic flow of material exists until fracture, which may be due to DRX and subsequent grain boundary sliding (GBS) of the recrystallized grains. The grain coarsening in strain localization region may degrade the material flowing ability which results in the dynamic fracture.
Source: crossref · Quality: baseline

Research context

OpenAlex topics: Surface Treatment and Residual Stress · High-Velocity Impact and Material Behavior · Advanced Surface Polishing Techniques

SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.

Affiliations

School of Materials Science and Engineering , Jiangsu University , Zhenjiang 212013 , China

School of Mechanical Engineering , Jiangsu University , Zhenjiang 212013 , China

SUMEC Hardware and Tools Co., Ltd. , Nanjing 210032 , China

References (40)

Show source-provided references
1. [1] Daehn G.S., High-velocity metal forming: ASM International, Materials Park, Ohio, 2006.10.31399/asm.hb.v14b.a000512710.31399/asm.hb.v14b.a0005127 ↗
2. [2] Zhang Y., Babu S. S., Prothe C., Blakely M., Kwasegroch J., Laha M., J. Mater. Process. Technol., 211 (2011), 944.10.1016/j.jmatprotec.2010.01.00110.1016/j.jmatprotec.2010.01.001 ↗
3. [3] Khardin M., Harhash M., Chernikov D., Glushchenkov V., Palkowski H., Compos. Struct., 252 (2020), 112729.10.1016/j.compstruct.2020.11272910.1016/j.compstruct.2020.112729 ↗
4. [4] Iyama H., Higa Y., Nishi M., Itoh S., Int. J. Mult., 11 (2017), 233.
5. [5] Li J., Gao H., Cheng G.J., J. Manuf. Sci. Eng.-Trans., ASME 132 (2010), 061005.
6. [6] Barati Darband G., Aliofkhazraei M., Khorsand S., Sokhanvar S., Kaboli A., Arab. J. Chem., 13 (2020), 1763.10.1016/j.arabjc.2018.01.01310.1016/j.arabjc.2018.01.013 ↗
7. [7] Li J., Chung T.F., Chen Y.P., Cheng G.J., Nano Lett., 12 (2012), 4577.10.1021/nl301817t2287685010.1021/nl301817t ↗
8. [8] Xiong F., Yang H., Liu K., Man J., Chen H., Opt. Laser Technol., 120 (2019), 105762.10.1016/j.optlastec.2019.10576210.1016/j.optlastec.2019.105762 ↗
9. [9] Jin S., Wang Y., Motlag M., Gao S., Xu J., Nian Q., Wu W., Cheng G.J., Adv. Mater., 30 (2018).10.1002/adma.2017058402935612910.1002/adma.201705840 ↗
10. [10] Choi D.C., Kim H.S., Opt. Lasers Eng., 124 (2020), 105799.10.1016/j.optlaseng.2019.10579910.1016/j.optlaseng.2019.105799 ↗
11. [11] Jin S., Zhou Z., Sakr E.S.A., Motlag M., Huang X., Tong L., Bermel P., Ye L., Cheng G.J., Small, 15 (2019), e1900481.10.1002/smll.2019004813095794110.1002/smll.201900481 ↗
12. [12] Man J., Yang H., Wang Y., Chen H., Xiong F., Opt. Laser Technol., 119 (2019), 105669.10.1016/j.optlastec.2019.10566910.1016/j.optlastec.2019.105669 ↗
13. [13] Shen Z., Wang X., Liu H., Wang Y., Wang C., Appl. Surf. Sci., 327 (2015), 307.10.1016/j.apsusc.2014.11.17210.1016/j.apsusc.2014.11.172 ↗
14. [14] Wang X., Du D., Zhang H., Shen Z., Liu H., Zhou J., Int. J. Mach. Tools Manuf., 67 (2013), 8.10.1016/j.ijmachtools.2012.12.00310.1016/j.ijmachtools.2012.12.003 ↗
15. [15] Nagarajan B., Castagne S., Wang Z., Zheng H. Y., Nadarajan K., Int. J. Mater. Form., 10 (2017), 109.10.1007/s12289-015-1264-510.1007/s12289-015-1264-5 ↗
16. [16] Yu C., Gao H., Yu H., Jiang H., Cheng G.J., Appl. Phys. Lett., 95 (2009), 091108.10.1063/1.3222863
17. [17] Shen Z., Zhang J., Liu H., Wang X., Ma Y., Int. J. Mach. Tools Manuf., 141 (2019), 1.10.1016/j.ijmachtools.2019.03.00410.1016/j.ijmachtools.2019.03.004 ↗
18. [18] Balanethiram V.S., Daehn G.S., Scr. Mater., 30 (1994), 515.10.1016/0956-716X(94)90613-010.1016/0956-716X(94)90613-0 ↗
19. [19] Jenab A., Green D.E., Alpas A.T., Golovashchenko S.F., J. Mater. Process. Technol., 255 (2018), 914.10.1016/j.jmatprotec.2017.12.03710.1016/j.jmatprotec.2017.12.037 ↗
20. [20] Psyk V., Risch D., Kinsey B.L., Tekkaya A.E., Kleiner M., J. Mater. Process. Technol., 211 (2011), 787.10.1016/j.jmatprotec.2010.12.01210.1016/j.jmatprotec.2010.12.012 ↗
21. [21] Mynors D.J., Zhang B., J. Mater. Process. Technol., 125 (2002), 1.10.1016/S0924-0136(02)00413-210.1016/S0924-0136(02)00413-2 ↗
22. [22] Murr L.E., Pizaña C., Metall. Mater. Trans. A-Phys. Metall. Mater. Sci., 38 (2007), 2611.10.1007/s11661-007-9185-710.1007/s11661-007-9185-7 ↗
23. [23] Cheng G.J., Pirzada D., Ming Z., J. Appl. Phys., 101 (2007), 063108.10.1063/1.271033410.1063/1.2710334 ↗
24. [24] Liu H.X., Hu Y., Wang X., Shen Z.B., Li P., Gu C.X., Mater. Sci. Eng. A-Struct. Mater. Prop. Microstruct. Process., 564 (2013), 13.
25. [25] Nagarajan B., Castagne S., Wang Z., Zheng H. Y., Appl. Phys. A-Mater. Sci. Process., 121 (2015), 695.10.1007/s00339-015-9460-110.1007/s00339-015-9460-1 ↗
26. [26] Shen Z., Liu H., Wang X., Wang C., Appl. Surf. Sci., 369 (2016), 288.10.1016/j.apsusc.2016.02.06310.1016/j.apsusc.2016.02.063 ↗
27. [27] Shen Z., Zhang J., Li P., Liu H., Yan Z., Ma Y., J. Manuf. Process., 37 (2019), 82.10.1016/j.jmapro.2018.11.01510.1016/j.jmapro.2018.11.015 ↗
28. [28] Wang K., Tao N.R., Liu G., Lu J., Lu K., Acta Mater., 54 (2006), 5281.10.1016/j.actamat.2006.07.01310.1016/j.actamat.2006.07.013 ↗
29. [29] Li Y. S., Tao N. R., Lu K., Acta Mater., 56 (2008), 230.10.1016/j.actamat.2007.09.02010.1016/j.actamat.2007.09.020 ↗
30. [30] Sun H.Q., Shi Y.N., Zhang M.X., Lu K., Acta Mater., 55 (2007), 975.10.1016/j.actamat.2006.09.01810.1016/j.actamat.2006.09.018 ↗
31. [31] Rittel D., Landau P., Venkert A., Phys. Rev. Lett., 101 (2008), 165501.10.1103/PhysRevLett.101.1655011899968310.1103/PhysRevLett.101.165501 ↗
32. [32] Esquivel E.V., Murr L.E., Mater. Sci. Eng. A-Struct. Mater. Prop. Microstruct. Process., 409 (2005), 13.
33. [33] Mishra A., Kad B., Gregori F., Meyers M., Acta Mater., 55 (2007), 13.10.1016/j.actamat.2006.07.00810.1016/j.actamat.2006.07.008 ↗
34. [34] Cao F., Li Z., Zhang N., Ding H., Yu F., Zuo L., Mater. Sci. Eng. A-Struct. Mater. Prop. Microstruct. Process., 571 (2013), 167.10.1016/j.msea.2013.02.01010.1016/j.msea.2013.02.010 ↗
35. [35] Tao N.R., Lu K., Scr. Mater., 60 (2009), 1039.10.1016/j.scriptamat.2009.02.00810.1016/j.scriptamat.2009.02.008 ↗
36. [36] Taylor G.I., Quinney H., Proc. R. Soc. London Ser. A-Math. Phys. Eng. Sci., A413 (1934), 307.10.1098/rspa.1934.0004 ↗
37. [37] Rittel D., Wang Z.G., Merzer M., Phys. Rev. Lett., 96 (2006), 075502.10.1103/PhysRevLett.96.0755021660610410.1103/PhysRevLett.96.075502 ↗
38. [38] Zener C., Hollomon J. H., J. Appl. Phys., 15 (1944), 22.10.1063/1.170736310.1063/1.1707363 ↗
39. [39] Xu Y., Zhang J., Bai Y., Meyers M.A., Metall. Mater. Trans. A-Phys. Metall. Mater. Sci., 39 (2008), 811.10.1007/s11661-007-9431-z10.1007/s11661-007-9431-z ↗
40. [40] Rittel D., 9th International Conference on Mechanical and Physical Behaviour of Materials under Dynamic Loading, 2009, p. 955.10.1051/dymat/2009134 ↗