Tribological performance of Orvar 2M tool steel coated with ALWIN XC for improved forging tool durability
Source abstract
Abstract
Abstract This study presents a comprehensive evaluation of the tribological performance of hot-work tool steel Orvar 2M in its uncoated state and after surface modification with a hard physical vapor deposition (PVD) AlWIN XC coating, intended for hot forging applications. The research followed a sequential experimental approach, combining preliminary laboratory tests, advanced high-temperature tribological tests, and industrial verification. Preliminary dry-abrasive wear tests at room temperature were performed for both uncoated and coated variants. These tests provided an initial comparative assessment of abrasive wear resistance and allowed identification of dominant surface degradation mechanisms. The uncoated steel exhibited localized abrasive wear, including microcracks and scratches, while the AlWIN XC coating significantly reduced material loss and stabilized the wear process. For a more representative analysis, ball-on-disc tests were conducted at 200°C, corresponding to the operational temperature of forging tools. The AlWIN XC coating demonstrated a stable coefficient of friction and low wear rate. Scanning electron microscopy observations and energy dispersive X-ray spectroscopy analyses enabled correlation of microstructural and chemical changes with the main degradation mechanisms. Industrial-scale forging trials confirmed that coated tools achieved more than a twofold increase in lifespan compared to uncoated steel. The results demonstrate the reliability and relevance of the applied tribological testing methodology as a predictive tool for tool durability. These findings also support the further development and optimization of PVD-coated forging tools for enhanced service life under industrial conditions.
Source: crossref · Quality: baseline
Research context
OpenAlex topics: Metallurgy and Material Forming · Metal and Thin Film Mechanics · Metal Alloys Wear and Properties
SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.
Affiliations
Department of Metal Forming, Welding and Metrology, Faculty of Mechanical Engineering, Wroclaw University of Science and Technology , Wroclaw , Poland
References (34)
Show source-provided references
1. Hutchings, I.M., Shipway, P., Tribology: Friction and wear of engineering materials, (2nd ed.), Butterworth-Heinemann, 201710.1016/B978-0-08-100910-9.00003-9 ↗
2. Tang, Z., Li, W., Yang, Z., Wang, J., Effect of solution and artificial aging heat treatment on the hardness, friction and wear properties of laser cladding and roll-formed 18Ni300 materials, Mater. Sci.-Poland, 2024, 42(2): 26–40. 10.2478/msp-2024-001710.2478/msp-2024-0017 ↗
3. Roberts, G., Krauss, G., Kennedy, R., Tool steels, ASM International, 199810.31399/asm.tb.ts5.9781627083584 ↗
4. ASTM International, ASTM G99–17: Standard test method for wear testing with a pin-on-disk apparatus, ASTM International, 2016
5. International Organization for Standardization, ISO 7148-1: Plain bearings – Tribological testing of bearing materials – Part 1: Determination of friction and wear properties of self-lubricating materials (ISO 7148), ISO, 1995
6. Hawryluk, M., Marzec, J., Lachowicz, M., Makuła, P., Nowak, K., Evaluation of the possibility of improving the durability of tools made of X153CrMoV12 steel used in the extrusion of a clay band in ceramic roof tile production, Mater. Sci.-Poland, 2023, 41(1): 94–109. https://sciendo.com/pl/article/10.2478/msp-2023-0011.10.2478/msp-2023-0011 ↗
7. Straffelini, G., Friction and wear: Methodologies for design and control, Springer, 201510.1007/978-3-319-05894-8 ↗
8. Vergne, C., Boher, C., Wear of hot-work tool steels under sliding contact, Wear, 2006, 260(7–8): 789–797. 10.1016/j.wear.2005.06.038
9. Podgornik, B., Leskovšek, V., High temperature wear mechanisms of tool steels, Tribol. Int., 2010, 43(12): 2345–2352. 10.1016/j.triboint.2010.06.004
10. Wang, L., Zhang, T., Li, X., Tribological behavior of hot-work tool steel under dry sliding, Wear, 2012, 292–293: 21–28. 10.1016/j.wear.2012.07.009
11. Bay, N., Wanheim, T., Friction and wear in metal forming, CIRP Ann., 1992, 41(2): 645–650. 10.1016/S0007-8506(07)63277-510.1016/S0007-8506(07)63251-X ↗
12. Muro, M., Artola, G., Gorriño, A., Angulo, C., Wear and friction evaluation of different tool steels for hot stamping, Adv. Mater. Sci. Eng., 2018, 2018: 3296398. 10.1155/2018/329639810.1155/2018/3296398 ↗
13. Joun, M.S., Wear and durability of tool steels in hot forging processes. J. Mater. Process. Technol., 2008, 205(1–3): 426–433. 10.1016/j.jmatprotec.2007.11.030
14. Kovačević, L., Vilotić, D., Tribological performance of hot work steels, Wear, 2011, 271(1–2): 212–220. 10.1016/j.wear.2010.09.005
15. Demir, M., Kanca, E., Karahan, I.H., Effect of saccharin addition on formation, wear and corrosion resistance of electrodeposited Ni-Cr coatings, Mater. Sci.-Poland, 2024, 41(3): 111–125, Wroclaw University of Science and Technology. 10.2478/msp-2023-003610.2478/msp-2023-0036 ↗
16. Hawryluk, M., Dudkiewicz, Ł., Zwierzchowski, M., Polak, S., Lachowicz, M., Ziemba, J., et al., Influence of the nitriding process on the durability of tools used in the production of automotive forgings in industrial hot die forging processes on hammers, Mater. Sci.-Poland, 2024, 42(4): 113–130. 10.2478/msp-2024-004710.2478/msp-2024-0047 ↗
17. ASTM International, ASTM G133 – Standard test method for linearly reciprocating ball-on-flat sliding wear, ASTM International, 2017
18. International Organization for Standardization, ISO 20808: Physical vapour deposition (PVD) coatings – Characterization (tribological properties), ISO, 2012
19. Zhang, S., Wang, L., Kong, H., Recent advances in PVD coatings for high-temperature tribological applications, Surf. Coat. Technol., 2020, 385: 125430. 10.1016/j.surfcoat.2020.12543010.1016/j.surfcoat.2020.125430 ↗
20. Holmberg, K., Matthews, A., Coatings tribology: Properties, mechanisms, techniques and applications, (2nd ed.), Elsevier, 2009
21. Stachowiak, G.W., Batchelor, A.W., Engineering tribology, (4th ed.), Butterworth-Heinemann, 2014
22. Pawlak, W., Urbaniak, W., Kulczyk, M., Influence of ceramic counterpart material on tribological behaviour of thin hard coatings, Tribol. Int., 2019, 138: 111–120. 10.1016/j.triboint.2019.01.045
23. Khadem, M., Jahanmir, S., High-temperature tribological behaviour of advanced PVD coatings: A review, Wear, 2021, 488–489: 204178. 10.1016/j.wear.2021.204178
24. Holmberg, K., Friction and wear of coatings at elevated temperatures, Tribol. Int., 2017, 115: 567–578. 10.1016/j.triboint.2017.07.009
25. Vasileiou, A., Denkena, B., Breidenstein, B., Topographical analysis of wear tracks on thin films using 3D areal parameters, Wear, 2020, 454–455: 203324. 10.1016/j.wear.2020.203324
26. Sadeghi, A., Zhang, T., Komvopoulos, K., Wear mechanisms and durability of advanced PVD coatings under severe tribological loading, Surf. Coat. Technol., 2021, 410: 126939. 10.1016/j.surfcoat.2021.126939
27. Hawryluk, M., Gronostajski, Z., Widomski, P., Kaszuba, M.D., Ziemba, J., Smolik, J., Influence of the application of a PN + Cr/CrN hybrid layer on the improvement of the lifetime of hot forging tools, J. Mater. Process. Technol., 2018, 258: 226–23810.1016/j.jmatprotec.2018.03.029 ↗
28. Hawryluk, M., Gronostajski, Z., Kaszuba, M.D., Polak, S., Widomski, P., Smolik, J., Analysis of the wear of forging tools surface layer after hybrid surface treatment, Int. J. Mach. Tools Manufacture, 2017, 114, 60–7110.1016/j.ijmachtools.2016.12.010 ↗
29. Nose, Y., Kawamoto, M., Funabashi, H., Formation and evolution of tribo-oxide layers on hard coatings at elevated temperatures, Surf. Coat. Technol., 2018, 349, 1036–1045. 10.1016/j.surfcoat.2018.06.078
30. Wojtaszek, M., Lisiecki, Ł., Łukaszek-Sołek, A., Korpała, G., Zyguła, K., Śleboda, T., et al., Application of processing maps and numerical modelling for identification of parameters and limitations of hot forging process of 80MnSi8-6 steel, Arch. Civ. Mech. Eng., 2023, 23: 240. 10.1007/s43452-023-00783-810.1007/s43452-023-00783-8 ↗
31. Hawryluk, M., Dudkiewicz, Ł., Jabłońska, M., Polak, S., & Marzec, J., Analysis of the destruction of a die insert used in the industrial process of hot die forging to produce a yoke forging, Eng. Fail. Anal., 2024, 164, 108661. 10.1016/j.engfailanal.2024.10866110.1016/j.engfailanal.2024.108661 ↗
32. Chen, J., Wang, S., Li, Y., Zhang, G., Oxidative wear behavior of H13 steel under dry sliding conditions at elevated temperatures, Tribology, 2011, 31(4): 317–322
33. Cui, X., Wang, Z., Shen, B., Liu, J., Effect of tempering conditions on wear resistance in various wear mechanisms of H13 steel, Tribol. Int., 2011, 44(7–8): 898–905. 10.1016/j.triboint.2011.02.00610.1016/j.triboint.2011.03.005 ↗
34. Wang, Y., Li, J., Zhang, H., Chen, Z., Impact of applied loads on wear mechanisms in H13 steel at various preheating temperatures during laser powder bed fusion additive manufacturing, Wear, 2024, 556–557: 205538. 10.1016/j.wear.2024.20553810.1016/j.wear.2024.205538 ↗