journal article·2025-12-01Open access

A review of W-temper forming methods for high-strength 7xxx aluminum alloy sheet

Mateusz Skwarski

Materials Science-Poland· Volume 43· Issue 4

Abstract

Abstract The manuscript provides a comprehensive overview of the W-temper forming (WT-F) process employed in the fabrication of sheet metal from 7xxx alloys. A diagram of the forming process is presented, taking into account the individual stages and the most important parameters of heat and plastic treatment. The literature review covers the characteristics of alloys tested during WT-F: EN AW-7075 and EN AW-7021. An analysis of previously published results was conducted in the following areas: strength and hardness tests, the effect of natural and artificial aging time on the mechanical properties of supersaturated aluminum alloys, determination of forming limit diagrams in the W-temper state and WT-F of U-profiles, car B-pillars, car floor panels, and door beams. A literature review showed that forming EN AW-7075 and EN AW-7021 in the W-temper state allows for the production of crack-free products, which is impossible to form with cold forming of sheets in the T6 state. Numerous studies have successfully formed components with complex geometries without defects or cracks, while achieving high true tensile strength values, reaching up to 600–620 MPa – significantly above the levels of typical 5000 and 6000 series alloys used in the automotive industry. While paint baking slightly reduces strength and ductility, it can also improve yield strength.
Source: crossref · Quality: baseline

Research context

OpenAlex topics: Metal Forming Simulation Techniques · Microstructure and mechanical properties · Metallurgy and Material Forming

SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.

Affiliations

Department of Metal Forming, Welding, and Metrology, Faculty of Mechanical Engineering, Wroclaw University of Science and Technology, Wyspiańskiego 27 , 50-370 Wroclaw , Poland

Center for Materials Engineering and Metal Forming, Wroclaw University of Science and Technology, Lukasiewicza 5 , 50-371 Wroclaw , Poland

References (28)

Show source-provided references
1. Gądek, T., Majewski, M., Research on the effect of temperature increase during flow forming without cooling on 6060 aluminum alloy, Mater. Sci. Pol., 2023, 41: 74–84. 10.2478/msp-2023-003310.2478/msp-2023-0033 ↗
2. De Cooman, B.C., Estrin, Y., Kim, S.K., Twinning-induced plasticity (TWIP) steels, Acta Mater., 2018, 142: 283–362. 10.1016/j.actamat.2017.06.04610.1016/j.actamat.2017.06.046 ↗
3. Lisiecka-Graca, P., Lisiecki, Ł., Zyguła, K., Wojtaszek, M., Evaluation of cracking risk of 80MnSi8-6 nanobainitic steel during hot forging in the range of lower temperature limits, Mater. Sci. Pol., 2024, 42: 171–185. 10.2478/msp-2024-001110.2478/msp-2024-0011 ↗
4. Kannan, P.R., Thanigaivelan, R., Thiraviam, R., Pradeep Kumar, K., Performance studies on hybrid nano-metal matrix composites for wear and surface quality, Mater. Sci. Pol., 2023, 41: 288–300. 10.2478/msp-2023-002010.2478/msp-2023-0020 ↗
5. Dai, Y., Yan, L., Hao, J., Review on micro-alloying and preparation method of 7xxx series aluminum alloys: Progresses and prospects, Mater., 2022, 15(3): 1216. 10.3390/ma1503121610.3390/ma15031216 ↗
6. Lachowicz, M.M., Metallurgical aspects of the corrosion resistance of 7000 series aluminum alloys – a review, Mater. Sci. Pol., 2023, 41: 159–180. 10.2478/msp-2023-004110.2478/msp-2023-0041 ↗
7. Chang, L., Yuan, S., Huang, X., Cai, Z., Determination of Johnson-Cook damage model for 7xxx laminated aluminum alloy and simulation application, Mater. Today Commun., 2023, 34: 105224. 10.1016/j.mtcomm.2022.10522410.1016/j.mtcomm.2022.105224 ↗
8. Zwolak, M., Sliwa, R., Analysis of the influence of dies geometry on the process extrusion force and properties of the extrudate obtained in the process of cold extrusion of 7075 aluminum alloy by the KOBO method, Mater. Sci. Pol., 2024, 42: 92–106. 10.2478/msp-2024-000810.2478/msp-2024-0008 ↗
9. Zhou, B., Liu, B., Zhang, S., The advancement of 7xxx series aluminum alloys for aircraft structures: A review, Metals (Basel), 2021, 11: 718. 10.3390/met1105071810.3390/met11050718 ↗
10. Omer, K., Abolhasani, A., Kim, S., Nikdejad, T., Butcher, C., Wells, M., et al., Process parameters for hot stamping of AA7075 and D-7xxx to achieve high performance aged products, J. Mater. Process. Technol., 2018, 257: 170–179. 10.1016/j.jmatprotec.2018.02.03910.1016/j.jmatprotec.2018.02.039 ↗
11. Krajewski, P., Stamping of age-hardenable aluminum alloy sheets, United States Pat. US 2012/0186706 A1, Vol. 002, 2012, p. 354. 10.1037/t24245-000
12. Gronostajski, Z., Jaśkiewicz, K., Kaczyński, P., Skwarski, M., Polak, S., Krawczyk, J., et al., W-Temper forming of B-pillar from 7075 aluminum alloy, CIRP Ann., 2022, 71: 221–224. 10.1016/j.cirp.2022.03.01910.1016/j.cirp.2022.03.019 ↗
13. Kaczyński, P., Skwarski, M., Jaśkiewicz, K., Development of the technology for press-forming of energy-absorbing elements made of 7075 aluminum alloy, J. Manuf. Process., 2020, 50: 676–683. 10.1016/j.jmapro.2020.01.02310.1016/j.jmapro.2020.01.023 ↗
14. Liu, Q., Chen, S., Gu, R., Wang, W., Wei, X., Effect of heat treatment conditions on mechanical properties and precipitates in sheet metal hot stamping of 7075 aluminum alloy, J. Mater. Eng. Perform., 2018, 27: 4423–4436. 10.1007/s11665-018-3588-z10.1007/s11665-018-3588-z ↗
15. Chen, J., Zhen, L., Yang, S., Shao, W., Dai, S., Investigation of precipitation behavior and related hardening in AA 7055 aluminum alloy, Mater. Sci. Eng. A., 2009, 500: 34–42. 10.1016/j.msea.2008.09.06510.1016/j.msea.2008.09.065 ↗
16. Zhen, L., Chen, J., Yang, S., Shao, W., Dai, S., Development of microstructures and texture during cold rolling in AA 7055 aluminum alloy, Mater. Sci. Eng. A., 2009, 504: 55–63. 10.1016/j.msea.2008.10.05510.1016/j.msea.2008.10.055 ↗
17. Argandoña, E.S., Galdos, L., Ortubay, R., Mendiguren, J., Agirretxe, X., Room temperature forming of AA7075 aluminum alloys: W-temper process, Key Eng. Mater., 2015, 651–653: 199–204. 10.4028/www.scientific.net/KEM.651-653.19910.4028/www.scientific.net/KEM.651-653.199 ↗
18. Sajadifar, S.V., Suckow, T., Chandra, C.K., Heider, B., Heidarzadeh, A., Zavašnik, J., et al., Assessment of the impact of process parameters on the final material properties in forming of EN AW 7075 employing a simulated forming process, J. Manuf. Process., 2023, 86: 336–353. 10.1016/j.jmapro.2022.12.05610.1016/j.jmapro.2022.12.056 ↗
19. Schuster, P.A., Österreicher, J.A., Kirov, G., Sommitsch, C., Kessler, O., Mukeli, E., Characterisation and comparison of process Chains for producing automotive structural parts from 7xxx Aluminium Sheets, Metals (Basel), 2019, 9: 1–15. 10.3390/met903030510.3390/met9030305 ↗
20. Choi, Y., Lee, J., Panicker, S.S., Jin, H.K., Panda, S.K., Lee, M.G., Mechanical properties, springback, and formability of W-temper and peak aged 7075 aluminum alloy sheets: Experiments and modeling, Int. J. Mech. Sci., 2020, 170: 69–84. 10.1016/j.ijmecsci.2019.10534410.1016/j.ijmecsci.2019.105344 ↗
21. Chen, J.Z., Zhen, L., Fan, L.W., Yang, S.J., Dai, S.L., Shao, W.Z., Portevin-Le Chatelier effect in Al-Zn-Mg-Cu-Zr aluminum alloy, Trans. Nonferrous Met. Soc. China (Engl. Ed.), 2009, 19: 1071–1075. 10.1016/S1003-6326(08)60408-210.1016/S1003-6326(08)60408-2 ↗
22. Lee, J., Bong, H.J., Kim, D., Lee, Y.S., Choi, Y., Lee, M.G., Application of combined W-temper and cold forming technology to high-strength aluminum alloy automotive parts, JOM, 2019, 71: 4393–4404. 10.1007/s11837-019-03779-z10.1007/s11837-019-03779-z ↗
23. Hua, L., Liu, S., Wei, P., Hu, Z., Ye, X., Deformation behavior, paint-bake response and microstructure evolution of pre-hardened 7075 aluminum alloy, Mater. Sci. Eng. A., 2025, 945: 148967. 10.1016/j.msea.2025.14896710.1016/j.msea.2025.148967 ↗
24. Mackenzie, J., Nwekirk, S., Quench factor analysis for heat treatment optimization of 7XXX aluminum alloys, Proceedings of the 8th Semin, IFHTSE, Dubrovnik, Croat, 2001, p. 119
25. Min, J., Xie, F., Liu, Y., Hou, Z., Lu, J., Lin, J., Experimental study on cold forming process of 7075 aluminum alloy in W temper, CIRP J. Manuf. Sci. Technol., 2022, 37: 11–18. 10.1016/j.cirpj.2022.01.00110.1016/j.cirpj.2022.01.001 ↗
26. Nasim, W., Kulkarni, S.S., Soulami, A., Efe, M., Rohatgi, A., Room temperature stamping of high-strength aluminum for lightweight structural automotive components, J. Mater. Eng. Perform., 2024, 33: 11876–11887. 10.1007/s11665-023-08810-810.1007/s11665-023-08810-8 ↗
27. Choi, Y., Ha, J., Lee, M.G., Korkolis, Y.P., Effect of plastic anisotropy and Portevin-Le Chatelier bands on hole-expansion in AA7075 sheets in -T6 and -W tempers, J. Mater. Process. Technol., 2021, 296: 117211. 10.1016/j.jmatprotec.2021.11721110.1016/j.jmatprotec.2021.117211 ↗
28. Anbalagan, K., Duraisamy, V., Loganathan, R.V., Sam, P.P., Influence of cerium oxide nanoparticles on the tribological behavior of AA8090 aluminum alloy composites for aero, military, and marine industrial applications, Mater. Sci., 2024, 42: 101–112. 10.2478/msp-2024-004810.2478/msp-2024-0048 ↗