Effect on the electrical properties of flexible solar cells influenced by mechanical bending
Source abstract
Abstract
The effect of cyclic bending on the electrical properties of a flexible Cu 2ZnSn(S,Se) 4 (CZTSSe) solar cell fabricated on a Mo foil was investigated at curvature radii R of 35 and 50 mm. The device parameters obtained from the current–voltage curves of the solar cell were analyzed as a function of the number of bending cycles N. The sample was fabricated using two types of Mo foil substrates in the “perpendicular” and “parallel” rolling orientations. Compared with an unstressed solar cell, the relative solar efficiency Δη/ η 0 of the fabricated cell decreased monotonically by −8.8% under repeated bending until N = 3000 cycles, and the difference in Δη/ η 0 between the two rolling orientations was within 2.3%. Its degradation was caused by a decrease in the relative short-circuit density ΔJsc/ Jsc 0 and an increase in the relative series resistance ΔRs/ Rs 0 . Conversely, for the sample prepared in a different batch process, a similar decrease in Δη/ η 0 of −9.1% even after N = 1000 cycles under both tensile and compressive stresses was observed and the degradation of the fill factor ΔFF/ FF 0 and open-circuit voltage ΔVoc/ Voc 0 was concluded to relate with a change in the CZTSSe absorber layer.
Source: expertdata · Quality: candidate unverified · Source record ↗
Research context
OpenAlex topics: solar cell performance optimization · Silicon and Solar Cell Technologies · Thin-Film Transistor Technologies
SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.
References (42)
Show source-provided references
1. Stretchable and reflective displays: materials, technologies and strategies10.1186/s40580-019-0190-5 ↗
2. Mechanical analyses and structural design requirements for flexible energy storage devices10.1002/aenm.201700535 ↗
3. A review of flexible perovskite oxide ferroelectric films and their application
4. Bending Setups for reliability investigation of flexible electronics10.3390/mi12010078 ↗
5. Compressive and tensile bending of sputter deposited Al/Mo bilayers10.1016/j.scriptamat.2018.11.048 ↗
6. Electrical and optical degradation studies on AZO thin films under cyclic bending conditions10.1109/TDMR.2012.2236888 ↗
7. Novel symmetrical bifacial flexible CZTSSe thin film solar cells for indoor photovoltaic applications10.1038/s41467-021-23343-1 ↗
8. High flexible Cu2ZnSn(S,Se)4 solar cells by green solution-process10.1016/j.solener.2018.11.030 ↗
9. Ultra-flexible perovskite solar cells with crumpling durability: toward a wearable power source10.1039/C9EE01944H ↗
10. Performance evaluation of flexible CIGS modules based on operational data under outdoor conditions10.1002/ese3.1040 ↗
11. Recent progress in flexible–wearable solar cells for self-powered electronic devices10.1039/C9EE03046H ↗
12. Bending properties of anisotropic conductive films assembled chip-in-flex packages for wearable electronics applications10.1109/TCPMT.2015.2513062 ↗
13. Residual stress in CIGS thin film solar cells on polyimide: simulation and experiments10.1007/s10854-013-1610-7 ↗
14. Degradation of flexible thin-film solar cells due to a mechanical strain10.1016/j.opelre.2017.02.003 ↗
15. CIGS solar cells on flexible ultra-thin glass substrates: characterization and bending test10.1016/j.tsf.2015.09.006 ↗
16. 14%-efficient flexible CdTe solar cells on ultra-thin glass substrates10.1063/1.4870834 ↗
17. Effect of bending test on the performance of CdTe solar cells on flexible ultra-thin glass produced by MOCVD10.1016/j.solmat.2020.110552 ↗
18. Emergence of flexible kesterite solar cells: progress and perspectives10.1038/s41528-023-00250-7 ↗
19. Ceramic barrier layers for flexible thin film solar cells on metallic substrates: a laboratory scale study for process optimization and barrier layer properties10.1021/am504923z ↗
20. Photovoltaic performance of flexible Cu(In,Ga)Se2 thin-film solar cells with varying Cr impurity barrier thickness10.1016/j.cap.2013.09.005 ↗
21. Thin film CdTe-CdS heterojunction solar cells on lightweight metal substrates10.1016/S0927-0248(99)00039-2 ↗
22. Flexible Cu2ZnSn(S,Se)4 solar cells with over 10% efficiency and methods of enlarging the cell area10.1038/s41467-019-10890-x ↗
23. 9.63% efficient flexible Cu2ZnSn(S,Se)4 solar cells fabricated via scalable doctor-blading under ambient conditions10.1039/D1TA07073H ↗
24. Efficiency Enhancement of Cu(In,Ga)Se2 solar cells fabricated on flexible polyimide substrates using alkali-silicate glass thin layers
25. Modeling and testing the mechanical strength of solar cells10.1016/j.solmat.2013.06.048 ↗
26. Changes of photovoltaic properties of flexible CIGS solar cell under mechanical bending stress
27. Flexible kesterite thin-film solar cells under stress10.1038/s41528-022-00221-4 ↗
28. 8% Efficiency Cu2ZnSn(S,Se)4 (CZTSSe) thin film solar cells on flexible and lightweight molybdenum foil substrates10.1021/acsami.9b03195 ↗
29. Mechanical reliability of flexible encapsulation of III-V compound thin film solar cells10.1016/j.solener.2020.12.014 ↗
30. Bending effects of indium-zinc oxide thin films deposited on polyethylene terephthalate substrate by radio frequency magnetron sputtering
31. Flexibility testing strategies and apparatus for flexible electronics10.1109/TED.2016.2545706 ↗
32. Cyclic bending reliability and failure mechanism of printed biodegradable flexible supercapacitor on polymer substrate10.1021/acsami.2c08502 ↗
33. Monotonic and cyclic mechanical reliability of metallization lines on polymer substrates10.1557/jmr.2017.121 ↗
34. Effect of solid-H2S gas reactions on CZTSSe thin film growth and photovoltaic properties of a 12.62% efficiency device10.1039/C9TA08310C ↗
35. Fabrication of Cu-rich CZTS thin films by two-stage process: effect of gas flow-rate in sulfurization process10.1016/j.molstruc.2021.129922 ↗
36. Bending strain and bending fatigue lifetime of flexible metal electrodes on polymer substrates10.3390/ma12152490 ↗
37. Chapter I-1-A - principles of solar cell operation
38. Fabrication of Cu2ZnSnS4 solar cell on a flexible glass substrate10.1016/j.tsf.2014.03.054 ↗
39. Understanding defects and band tailing characteristics and their impact on the device performance of Cu2ZnSn(S,Se)4 solar cells10.1039/D2TA00165A ↗
40. Sodium-assisted passivation of grain boundaries and defects in Cu2ZnSnSe4 thin films10.1039/C9CP06537G ↗
41. Defect suppression for high-efficiency kesterite CZTSSe solar cells: advances and prospects10.1016/j.cej.2023.142121 ↗
42. Nanoimaging of open-circuit voltage in photovoltaic devices10.1002/aenm.201501142 ↗