Influence of microalloying additions on thickness of grain boundary carbides in ferrite–pearlite steels
Source abstract
Abstract
For a series of plain C and microalloyed steels at two levels of Mn, the growth of grain boundary carbides has been monitored after heating to 920°C and cooling at 40 and 150 K min−1 through the austenite–ferrite/pearlite transformation down to room temperature. In pearlite free steels, on cooling to room temperature, all the C in solution in the ferrite is able to precipitate as carbides at the boundaries and the grain boundary carbide thickness is dependent on the number of nucleation sites for precipitation. Increasing the cooling rate increases the number of sites and reduces the carbide thickness. In ferrite–pearlite steels, the grain boundary carbides form the ‘tails’ to the pearlite colonies. The thickness of the grain boundary carbide is related to the pearlite reaction, since the temperature at which this occurs controls both the thickness of the carbide nuclei and the amount of C available for precipitating out on these tails. Increasing the cooling rate and Mn content causes a decrease in the transformation temperature and leads to finer carbides. The pearlite nose transformation temperature must be ≦600°C to produce fine (≦0·2 μm) carbides. The austenite grain size, which controls the pearlite colony size, is also very important in determining the thickness of carbides, since the finer the grain size, the greater the carbide density and,for a given amount of C available for precipitation, the finer the resulting carbides. Faster cooling or a higher Mn content refine the pearlite colony size leading to finer carbides. Compared with C–Mn–Al steels, Nb and Ti microalloying additions result in coarser carbides and higher carbide densities. The increased carbide density is due to the finer austenite grain size and the coarser carbides are due to the finer grain size raising the transformation temperature. The implications of these observations on impact behaviour are discussed.MST/1858
Source: openalex_inverted_index · Quality: baseline
Research context
OpenAlex topics: Microstructure and Mechanical Properties of Steels · Metal Alloys Wear and Properties · High Temperature Alloys and Creep
SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.
References (18)
Show source-provided references
1. ALLEN N. P. · Steel Inst. · 1953 · 174, 108
2. HAHN G. T. · Acta Metall. · 1962 · 200 · 634
3. 10.1016/0001-6160(65)90121-510.1016/0001-6160(65)90121-5 ↗
4. R. C. COCHRANE: 'Effect of second-phase particles on the mechanical properties of steel', 101; 1971, London, The Iron and Steel Institute.
5. PICKERING F. B. · 1971 · 9
6. 10.1179/03063457679043145310.1179/030634576790431453 ↗
7. 10.1179/msc.1979.13.6.34110.1179/msc.1979.13.6.341 ↗
8. 10.1179/03071697980327624610.1179/030716979803276246 ↗
9. 10.1179/mst.1986.2.10.104610.1179/mst.1986.2.10.1046 ↗
10. B. MINTZ, W. B. MORRISON, and R. C. COCHRANE: 'Advances in physical metallurgy and applications of steels', 222–228; 1982, London, The Metals Society.
11. 10.1179/mst.1989.5.2.15510.1179/mst.1989.5.2.155 ↗
12. 10.1179/mst.1987.3.10.84510.1179/mst.1987.3.10.845 ↗
13. S. A. SALTYKOV: in 'Quantitative Microscopy', (ed. R. T. De-Haff and F. N. Rhines), 100; 1968, New York, McGraw-Hill.
14. F. B. PICKERING: 'The bais of quantitative metallography'; 1976, London, The Institute of Metals.
15. SMITH R. P. · Trans. AIME · 1962 · 224 · 105
16. 10.1179/mst.1991.7.11.100510.1179/mst.1991.7.11.1005 ↗
17. CURRY D. A. · J. Mater. Sci. · 1978 · 12 · 511
18. B. MINTZ: in Proc. 6th Int. Conf. on Fracture, 'Advances in fracture research', (ed. S. R. Valluri et al.), Vol. 2, 1247; 1984, Oxford, Pergamon Press.10.1016/B978-1-4832-8440-8.50110-1 ↗