journal article·1994-10

Compressive behaviour of partially remelted A356 alloys reinforced with SiC particles

L. Nguyen Thanh, M. Suéry

Materials Science and Technology· Volume 10· Issue 10
Publisher page

Abstract

The compressive behaviour of partially remelted A356 alloys reinforced with 20 vol.-%SiC particles (Duralcan F3 A20S) is investigated. The influence of isothermal holding time in the range 2–120 min in the semisolid state before compression at a constant strain rate of 0·1 S−l is investigated. It is observed that deformation always takes place under very low stresses, which decrease as holding time increases. Comparison is made with the unreiriforced alloy (A356) together with composites extruded after fabrication. The compressive behaviour in the semisolid state at various constant strain rates in the range 6·2 × 10−3–0·4 S−1 is also investigated. Theflow stresses are sensitive to strain rate according to the classical power law (σ=K03B5;m Kern, with values of m in the range 0·3–0·4. Microstructural characterisation of the specimens after partial remelting and after compression is also carried out and the correlations between the compressive behaviour and the microstructure are discussed. In particular, it is shown that the presence of the particles leads to finer, less agglomerated globules of the solid phase than in the unreiriforced alloy, which explains the high deformability of the composites.MST/1993
Source: openalex_inverted_index · Quality: baseline

Research context

OpenAlex topics: Aluminum Alloys Composites Properties · Advanced ceramic materials synthesis · Microstructure and mechanical properties

SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.

References (14)

Show source-provided references
1. J. C. VIALA, P. FORTIER, C. BERNARD, and J. BOUIX: in Proc. 1st Eur. Conf. on 'Composite materials', (ECCM-1), (ed. A. R. Bunsell et al.), 583–588; 1985, Bordeaux, France, European Association for Composite Materials.
2. R. Y. LIN and K. KANNIKESWARAN: in Proc. TMS Annual Meeting 'Interfaces in metal—ceramics composites', (ed. R. Y. Lin et al.), 153–164; 1990, Warrendale, PA, TMS.
3. G. SELVADURAY, R. HICHMAN, D. QUINN, D. RICHARD, and D. ROWLAND: in Proc. TMS Annual Meeting 'Interfaces in metal—ceramics composites', (ed. R. Y. Lin et al.), 271–289; 1990, Warrendale, PA, TMS.
4. D. J. LLOYD and E. DEWING: in Proc. Int. Symp. on 'Advanced structural materials', 27th Annual Conf. of Metallurgists (CIMM), (ed. D. S. Wilkinson), 71–77; 1989, Oxford, Pergamon Press.10.1016/B978-0-08-036090-4.50012-4 ↗
5. 10.1007/BF0056306710.1007/BF00563067 ↗
6. D. J. LLOYD and B. CHAMBERLAIN: in Proc. Int. Symp. Vast reinforced metal composites', (ed. S. G. Fishman and A. K. Dhingra), 263–269; 1988, Materials Park, OH, ASM International.
7. 10.1016/0956-716X(91)90156-U10.1016/0956-716X(91)90156-U ↗
8. M. A. BAYOUMI and M. sutity: in Proc. Int. Symp. 'Cast reinforced metal composites', (ed. S. G. Fishman and A. K. Dhingra), 167–172; 1988, Materials Park, OH, ASM International.
9. L. NGUYEN THANH and M. suktv: in Proc. 2nd Int. Conf. on 'Processing of semi-solid alloys and composites', (ed. S. B. Brown and M. C. Flemings), 427–435; 1992, Cambridge, MA, MIT Press.
10. W. A. VIAY, S. P. MIDSON, and K. P. YOUNG: in Proc. 2nd Int. Conf. on 'Processing of semi-solid alloys and composites', (ed. S. B. Brown and M. C. Flemings), 390–397; 1992, Cambridge, MA, MIT Press.
11. NGUYEN T. G. · Mater. Sci. Eng. · 1994 · A183,157
12. M. SUERY: in 'Formability and metallurgical structure', (ed. A. K. Sachdev and J. D. Embury), 283–302; 1986, Warrendale, PA, The Metallurgical Society.
13. M. SUERY, W. R. LOUE, L. NGUYEN THANH, and T. G. NGUYEN: in ‘Microstructural design by solidification processing', (ed. E. J. Lavernia and M. N. Gungor), 77–92; 1992, Warrendale, PA, The Minerals, Metals and Materials Society.
14. M. P. KENNEY, J. A. COURTOIS, R. D. EVANS, G. M. FARRIOR, C. P. KYONKA, A. A. KOCH, and K. P. YOUNG: in 'Metals handbook', 9 edn, Vol. 15, 'Casting', 327–338; 1988, Materials Park, OH, ASM International.