journal article·2014-10

Influence of shielding gases on preheat produced in surface coatings incorporating SiC particulates into microalloy steel using TIG technique

P. Patel, S. Mridha, T. N. Baker

Materials Science and Technology· Volume 30· Issue 12
Publisher page

Abstract

The use of a tungsten inert gas (TIG) welding torch has resulted in the development of an economical route for surface engineering of alloys, giving similar results to the more expensive high power laser. Owing to the preheating generated by both techniques, the extent of the temperature rise is sufficient to produce significant changes to the melt dimensions, microstructure and properties between the first and last tracks melted during the coating of a complete surface. The present study examines if similar changes can occur between the start and finish locations of a single track of 50 mm length. The results show that for a TIG melted surface of a microalloy steel substrate, with or without incorporating preplaced SiC particles, in either argon or argon–helium environments, a maximum temperature of 375°C developed in the second third of the track. Even over this short distance, a hardness decrease of >300 HV was recorded in the resolidified SiC coated substrate melt zone, microstructure of a cast iron with cracks was observed. In addition, porosity was found in all the tracks, with and without preplaced SiC powders.
Source: crossref · Quality: baseline

Research context

OpenAlex topics: High Entropy Alloys Studies · Welding Techniques and Residual Stresses · High-Temperature Coating Behaviors

SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.

Affiliations

Department of Mechanical Engineering, Indian Institute of Technology, Gandhinagar Gujarat, India

Department of Mechanical and Aerospace Engineering, University of Strathclyde Glasgow G1 1XJ, Scotland

References (22)

Show source-provided references
1. Ion JC: ‘Laser processing of engineering materials’; 2005, Amsterdam, Elsevier.10.1016/B978-075066079-2/50009-X ↗
2. 10.1533/978184569945110.1533/9781845699451 ↗
3. Toyserkani AKE and Corbin S: ‘Laser cladding’; 2005, Boca Raton, FL, CRC Press LLC.10.1201/9781420039177 ↗
4. 10.1179/02670849910151653310.1179/026708499101516533 ↗
5. 10.1016/S0924-0136(01)00609-410.1016/S0924-0136(01)00609-4 ↗
6. 10.1016/j.apsusc.2005.02.08810.1016/j.apsusc.2005.02.088 ↗
7. 10.1016/j.jallcom.2006.03.08310.1016/j.jallcom.2006.03.083 ↗
8. 10.1016/j.jmatprotec.2005.02.24710.1016/j.jmatprotec.2005.02.247 ↗
9. Mridha S · IJMME · 2012 · 7 · 48
10. Galloway AM · J. Mater. Des. Appl. · 2011 · 225 · 61
11. 10.1023/A:101866423141010.1023/A:1018664231410 ↗
12. 10.1016/S0924-0136(99)00088-610.1016/S0924-0136(99)00088-6 ↗
13. 10.1179/mst.1994.10.6.53610.1179/mst.1994.10.6.536 ↗
14. 10.1179/mst.1996.12.7.59510.1179/mst.1996.12.7.595 ↗
15. 10.1007/BF0035643110.1007/BF00356431 ↗
16. Čikara D · FME Trans. · 2009 · 37 · 151
17. 10.1016/S1359-6462(98)00329-710.1016/S1359-6462(98)00329-7 ↗
18. 10.4028/www.scientific.net/AMR.445.65510.4028/www.scientific.net/AMR.445.655 ↗
19. Easterling KE: ‘Introduction to physical metallurgy of welding’; 1992, London, Butterworth-Heinemann.
20. 10.1179/174328407X22656310.1179/174328407X226563 ↗
21. 10.1179/02670840010151701710.1179/026708400101517017 ↗
22. Raghaven V · J. Alloy Phase Diagrams India · 1986 · 2 · 97