journal article·2009-12

Similar and dissimilar RSW of low carbon and austenitic stainless steels: Effect of weld microstructure and hardness profile on failure mode

M. Pouranvari, S. P. H. Marashi

Materials Science and Technology· Volume 25· Issue 12
Publisher page

Abstract

In this paper, the failure behaviour of similar and dissimilar resistance spot welded joints of low carbon and austenitic stainless steel sheets was studied under tensile shear test with attention focused on the failure mode. Results showed that the microstructure of the fusion zone and the hardness distribution across the weld have a profound effect on the failure behaviour. Similar spot welds of stainless steel sheets exhibit the highest tendency to fail in interfacial failure mode, compared to low carbon steel similar spot welds and dissimilar low carbon and stainless steel spot welds. This behaviour is explained by the consideration of pullout failure location and hardness profile characteristics of each joint. It was shown that the failure mode transition is controlled by the hardness ratio of the fusion zone and the pullout failure location. In the case of dissimilar resistance spot welding, the hardness of the fusion zone which is governed by the dilution between two base metals, and the fusion zone size of the low carbon steel side are the dominant factors determining the failure mode of the joint.
Source: crossref · Quality: baseline

Research context

OpenAlex topics: Advanced Welding Techniques Analysis · Welding Techniques and Residual Stresses · Metal and Thin Film Mechanics

SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.

Affiliations

Materials and Metallurgical Engineering DepartmentSchool of Engineering, Islamic Azad University, Dezful Branch, Dezful, Iran;, Email: mpouranvari@yahoo.com

Mining and Metallurgical Engineering DepartmentAmirkabir University of Technology, Tehran, Iran

References (17)

Show source-provided references
1. 10.1016/j.engfailanal.2007.01.01810.1016/j.engfailanal.2007.01.018 ↗
2. Chao Y. J. · Sci. Technol. Weld. Join · 2003 · 8 · 133
3. 10.1179/174329307X16440910.1179/174329307X164409 ↗
4. Marya M. · J. Manufact. Sci. Eng · 2006 · 287 · 8
5. Marya M., and Gayden X. Q.: Weld 1, 2005, 84, 172s-182s.
6. 10.1179/174329307X16440910.1179/174329307X164409 ↗
7. Zuniga S., and Sheppard S. D.: in ‘Fatigue and fracture mechanics’, (ed.Piascik R. S. et al), Vol. 27, ASTM STP 1296, 469-489; 1997, Philadelphia, PA, USA, ASTM.10.1520/STP16249S ↗
8. Zuniga S. M. · 1994
9. Alenius M., Pohjanne P., Somervuorl M., and Hanninen H.: Weld. 1, 2007, 86, 305s-313s.
10. 10.1016/j.msea.2007.07.00710.1016/j.msea.2007.07.007 ↗
11. 10.1179/136217108X32547010.1179/136217108X325470 ↗
12. ‘Recommended practices for test methods and evaluation the resistance spot welding behavior of automotive sheet steels’, ANSI/ AWS/SAE D 8.9-97.
13. Gould J. E., Khurana S. P., and Li T.: Weld. 1, 2006, 86, Ills-116s.
14. Babu S. S., Reimer B. W., Santella M. L., and Feng Z.: Proc. 8th Sheet Metal Welding Conf., Detroit, MI, USA, October 1998, AWS, Paper5–2.
15. Schaeffler A. L. · Metal Frog · 1949 · 680 · 0B
16. Sun X., Stephens E. V., and Khaleel M. A.: Weld. 1, 2007, 86, 18s-25s.
17. 10.1115/1.155564810.1115/1.1555648 ↗