journal article·2009-03Open access

Measured residual stress distributions for low and high heat input single weld beads deposited on to SA508 steel

J. A. Francis, M. Turski, P. J. Withers

Materials Science and Technology· Volume 25· Issue 3

Abstract

In steel welds, the development of residual stress is often complicated by the solid state phase transformations that occur upon cooling. Here the authors present bulk residual stress distributions, as measured by neutron diffraction, for the configuration of a single pass gas tungsten arc weld bead deposited on to a 20 mm thick SA508 steel substrate. Two specimens were manufactured, one with a low heat input (1·2 kJ mm−1) and another with a high heat input (2·4 kJ mm−1). The resulting microstructures and residual stress distributions are discussed in terms of the differing thermal excursions across each weld. In regions that are austenitised during welding, the transformation strain on cooling is shown to compensate in part for thermal contraction strains. Accordingly, phase transformations in SA508 steel led to significant reductions in stress within the weld bead and much of the heat affected zone, while the highest tensile stresses were located immediately outside the heat affected zone boundary in the untransformed region.
Source: crossref · Quality: baseline

Research context

OpenAlex topics: Welding Techniques and Residual Stresses · Advanced Welding Techniques Analysis · Metal and Thin Film Mechanics

SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.

References (34)

Show source-provided references
1. 10.1088/0034-4885/70/12/R0410.1088/0034-4885/70/12/R04 ↗
2. 10.1115/1.148103510.1115/1.1481035 ↗
3. Turski M., Bouchard P. J., Steuwer A., and Withers P. J.: Acta Mater. 2008, 56, (14), 3598–3612.10.1016/j.actamat.2008.03.045 ↗
4. Bouchard P. J., Withers P. J., McDonald S. A., and Heenan R. K.: Acta Mater. 2004, 52, (1), 23–34.10.1016/j.actamat.2003.08.022 ↗
5. 10.1016/j.ijfatigue.2003.08.02010.1016/j.ijfatigue.2003.08.020 ↗
6. 10.1002/mawe.20050093310.1002/mawe.200500933 ↗
7. 10.1016/0308-0161(84)90028-010.1016/0308-0161(84)90028-0 ↗
8. 10.1016/0013-7944(89)90212-910.1016/0013-7944(89)90212-9 ↗
9. 10.1243/030932400151443110.1243/0309324001514431 ↗
10. 10.1179/174328006X7946310.1179/174328006X79463 ↗
11. 10.1023/A:102657440085810.1023/A:1026574400858 ↗
12. 10.1179/02670830110150998010.1179/026708301101509980 ↗
13. 10.1179/02670830110151008710.1179/026708301101510087 ↗
14. 10.1179/174328407X21311610.1179/174328407X213116 ↗
15. 10.1243/030932400151442210.1243/0309324001514422 ↗
16. 10.1016/j.ijpvp.2006.02.01510.1016/j.ijpvp.2006.02.015 ↗
17. Satoh K. · Trans. Jpn Weld. Soc · 1972 · 3 · 125
18. Satoh K. · Trans. Jpn Weld. Soc.y · 1972 · 3 · 135
19. 10.1016/S0029-5493(00)00440-410.1016/S0029-5493(00)00440-4 ↗
20. 10.1007/s11661-008-9616-010.1007/s11661-008-9616-0 ↗
21. 10.4028/www.scientific.net/MSF.475-479.412110.4028/www.scientific.net/MSF.475-479.4121 ↗
22. Krawitz A. D., and Winholtz R.: Mater. Sci. Eng. A, 1994, A185, (1-2),123–130.10.1016/0921-5093(94)90935-0 ↗
23. 10.1107/S002188980703026910.1107/S0021889807030269 ↗
24. Mannan S. L. · Trans. Ind Inst. Met · 1996 · 49 · 303
25. Bhadeshia H. K. D. H., and Honeycombe R. W. K. ‘Steels - microstructure and properties’, 3rd edn, 287-306; 2006, Oxford, Butterworth-Heinemann.10.1016/B978-075068084-4/50015-7 ↗
26. &# 00D8; Grong: ‘Metallurgical modelling of welding’, 2nd edn, 504-506; 1997, London, The Institute of Materials.
27. 10.1007/s11663-998-0101-310.1007/s11663-998-0101-3 ↗
28. MATLAB, version 7.2 (R2006a), The Math Works, Inc., Natick, MA, USA, 2006.
29. 10.1029/GL014i002p0013910.1029/GL014i002p00139 ↗
30. Francis J. A. · J. Press. Vess. Technol
31. 10.4028/www.scientific.net/MSF.490-491.29410.4028/www.scientific.net/MSF.490-491.294 ↗
32. 10.1016/S0924-0136(96)02727-610.1016/S0924-0136(96)02727-6 ↗
33. 10.4028/www.scientific.net/MSF.404-407.56110.4028/www.scientific.net/MSF.404-407.561 ↗
34. 10.1016/j.nucengdes.2006.03.02210.1016/j.nucengdes.2006.03.022 ↗