journal article·2019-08

Mechanical properties and failure of ECAE processed Mg97Y2Zn1 at different strain rates

Jianguo Li, Tao Suo, Yulong Li, Laszlo J. Kecskes, Qiuming Wei

Publisher page

Abstract

Abstract As-cast Mg97Y2Zn1 billets with a two-phase microstructure were processed with four passes of equal channel angular extrusion (ECAE) using different routes (A, BC, and C) at 350 °C to refine the microstructure. The duplex microstructure of this material consists of a Mg-rich alloy matrix with a long-periodic-stacking-order (LPSO) reinforcement phase. Mechanical properties were evaluated under both quasi-static and dynamic loading conditions. It was found that routes A and BC were more effective in producing a Mg alloy with nearly isotropic properties. For route C, the specimens more easily fractured due to pre-existing localized shear planes induced by ECAE. Microstructural observations revealed that the post-processed average matrix grain size could be as fine as ∼1 μm. Uniaxial compressive loading and micro-hardness measurements verified the enhancement of strength, and it was noticed that the increase of strength comes primarily from grain refinement of the Mg matrix. In the composite, we also focused on elucidating the deformation mechanism of the LPSO phase. It is believed that localized deformation is responsible for the final failure of the ECAE processed Mg97Y2Zn1 alloy under both quasi-static and high strain rate loading. The grain morphology and distribution after deformation indicated that the shear localization resulted from the rotation and rearrangement of grains. Moreover, cracks were found to propagate along the grain boundaries leading to final failure.
Source: openaire · Quality: candidate unverified · Source record ↗

Research context

OpenAlex topics: Magnesium Alloys: Properties and Applications · Aluminum Alloys Composites Properties · Microstructure and mechanical properties

SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.

References (75)

Show source-provided references
1. Magnesium and its alloys applications in automotive industry10.1007/s00170-007-1279-2 ↗
2. Recent magnesium alloy development for elevated temperature applications10.1179/095066004225010497 ↗
3. Validation of predicted residual stresses within direct chill cast magnesium alloy slab10.1007/s11661-011-1077-1 ↗
4. Deformation twinning in rolled WE43-T5 rare earth magnesium alloy: influence on strain hardening and texture evolution10.1016/j.actamat.2017.03.075 ↗
5. Precipitation in magnesium alloy WE54 during isothermal ageing at 250°C10.1016/S1359-6462(99)00084-6 ↗
6. Characterisation of strengthening precipitate phases in a Mg-Y-Nd alloy10.1016/S1359-6454(00)00013-6 ↗
7. Characterization of β' phase precipitates in an Mg-5 at%Gd alloy aged in a peak hardness condition, studied by high-angle Annular detector dark-field scanning transmission electron microscopy10.2320/matertrans.47.2109 ↗
8. Microstructure and mechanical properties of Mg-Zn-Y alloy sheet prepared by hot-rolling10.1016/j.msea.2012.09.059 ↗
9. The activity of non-basal slip systems and dynamic recovery at room temperature in fine-grained AZ31B magnesium alloys10.1016/S1359-6454(03)00005-3 ↗
10. Effect of multimodal microstructure evolution on mechanical properties of Mg-Zn-Y extruded alloy10.1016/j.actamat.2011.02.038 ↗
11. A two-step dynamic recrystallization induced by LPSO phases and its impact on mechanical property of severe plastic deformation processed Mg97Y2Zn1 alloy10.1016/j.jallcom.2017.02.107 ↗
12. Microstructure and mechanical behavior of ECAP processed AZ31B over a wide range of loading rates under compression and tension10.1016/j.mechmat.2015.03.001 ↗
13. Enhancement of properties in cast Mg-Y-Zn rod processed by severe plastic deformation10.1016/j.msea.2014.07.068 ↗
14. The texture and anisotropy of magnesium–zinc–rare earth alloy sheets10.1016/j.actamat.2006.11.013 ↗
15. Texture evolution during static recrystallization of cold-rolled magnesium alloys10.1016/j.actamat.2015.12.045 ↗
16. Statistic derivation of taylor factors for polycrystalline metals with application to pure magnesium10.1016/j.msea.2013.06.025 ↗
17. An atomic displacive model for {101¯2}<1¯011> twinning in hexagonal close packed metals with the emphasis on the role of partial stacking faults in formation of {101¯2} twins10.1016/j.actamat.2018.03.028 ↗
18. Non-basal slip systems in HCP metals and alloys: source mechanisms10.1016/S0921-5093(01)01027-9 ↗
19. Plastic anisotropy and the role of non-basal slip in magnesium alloy AZ31B10.1016/j.ijplas.2004.05.018 ↗
20. Study of slip mechanisms in a magnesium alloy by neutron diffraction and modeling10.1016/S1359-6462(02)00591-2 ↗
21. Statistical analyses of deformation twinning in magnesium10.1080/14786431003630835 ↗
22. Slip, twinning, and fracture in hexagonal close-packed metals10.1007/BF02648537 ↗
23. Influence of orientation on twin nucleation and growth at low strains in a magnesium alloy10.1016/j.actamat.2014.07.013 ↗
24. Experimentally quantifying critical stresses associated with basal slip and twinning in magnesium using micropillars10.1016/j.actamat.2017.06.008 ↗
25. How magnesium accommodates local deformation incompatibility: a high-resolution digital image correlation study10.1016/j.actamat.2017.05.040 ↗
26. Structure and stacking faults in layered Mg-Zn-Y alloys: a first-principles study10.1016/j.actamat.2008.01.046 ↗
27. Dislocation structure in rapidly solidified Mg97Zn1Y2 alloy with long period stacking order phase10.2320/matertrans.46.361 ↗
28. On the role of non-basal deformation mechanisms for the ductility of Mg and Mg-Y alloys10.1016/j.actamat.2010.08.031 ↗
29. On the room temperature deformation mechanisms of a Mg-Y-Zn alloy with long-period-stacking-ordered structures10.1016/j.actamat.2014.09.036 ↗
30. The effect of twin–twin interactions on the nucleation and propagation of {101¯2} twinning in magnesium10.1016/j.actamat.2013.02.030 ↗
31. Characteristic dislocation substructure in {101¯2} twins in hexagonal metals10.1016/j.scriptamat.2017.09.015 ↗
32. (1¯012) Twinning nucleation mechanisms in hexagonal-close-packed crystals10.1016/j.actamat.2009.07.047 ↗
33. Twinning and the ductility of magnesium alloys Part I: “Tension” twins10.1016/j.msea.2006.12.037 ↗
34. Twinning and the ductility of magnesium alloys Part II. "Contraction twins"10.1016/j.msea.2007.02.109 ↗
35. Anisotropy and non-uniformity in plastic behavior of AZ31 magnesium alloy plates10.2320/matertrans.44.452 ↗
36. Characteristics of the contraction twins formed close to the fracture surface in Mg-3Al-1Zn alloy deformed in tension10.1016/j.scriptamat.2008.06.041 ↗
37. Enhanced deformation mechanisms by anisotropic plasticity in polycrystalline Mg alloys at room temperature10.1007/s11661-005-0032-4 ↗
38. Strengthening and toughening mechanisms in Mg-Zn-Y alloy with a long period stacking ordered structure10.1016/j.actamat.2010.05.012 ↗
39. Fracture mechanism of a coarse-grained magnesium alloy during fracture toughness testing10.1080/09500830802537718 ↗
40. Strength and ductility with {101¯1}-{101¯2}double twinning in a magnesium alloy10.1038/ncomms11068 ↗
41. Long-period ordered structure in a high-strength nanocrystalline Mg-1at% Zn-2at% Y alloy studied by atomic-resolution Z-contrast STEM10.1016/S1359-6454(02)00191-X ↗
42. Novel hexagonal structure and ultrahigh strength of magnesium solid solution in the Mg-Zn-Y system10.1557/JMR.2001.0260 ↗
43. Rapidly solidified powder metallurgy Mg97Zn1Y2Alloys with excellent tensile yield strength above 600 MPa10.2320/matertrans.42.1172 ↗
44. Effect of long-period stacking ordered phase on mechanical properties of Mg97Zn1Y2 extruded alloy10.1016/j.actamat.2010.07.050 ↗
45. Plastic deformation behavior of 10H-type synchronized LPSO phase in a Mg-Zn-Y system10.1016/j.actamat.2016.02.037 ↗
46. Long period stacking structures observed in Mg97Zn1Y2 alloy10.1016/j.scriptamat.2004.04.003 ↗
47. Variation of long-period stacking order structures in rapidly solidified Mg97Zn1Y2 alloy10.1016/j.msea.2004.10.040 ↗
48. Highly ordered 10H-type long-period stacking order phase in a Mg-Zn-Y ternary alloy10.1016/j.scriptamat.2014.01.013 ↗
49. Formation of 14H long period stacking ordered structure and profuse stacking faults in Mg-Zn-Gd alloys during isothermal aging at high temperature10.1016/j.actamat.2007.08.033 ↗
50. Growth and transformation mechanisms of 18R and 14H in Mg–Y–Zn alloys10.1016/j.actamat.2012.08.022 ↗
51. Effect of multimodal microstructure evolution on mechanical properties of Mg-Zn-Y extruded alloy10.1016/j.actamat.2011.02.038 ↗
52. Dynamic recrystallization and texture evolution of Mg-Y-Zn alloy during hot extrusion process10.1016/j.matchar.2014.03.006 ↗
53. Experimental study of a structural magnesium alloy with high absorption energy under dynamic loading10.1016/S1359-6462(98)00296-6 ↗
54. Effect of grain refinement on tensile ductility in ZK60 magnesium alloy under dynamic loading10.2320/matertrans.42.1177 ↗
55. Impact tensile stress–strain characteristics of wrought magnesium alloys10.1046/j.1475-1305.2003.00086.x ↗
56. Anisotropic effects on the strain rate dependence of a wrought magnesium alloy10.1016/j.scriptamat.2008.10.011 ↗
57. Dynamic behavior of a rare-earth-containing Mg alloy, WE43B-T5, plate with comparison to conventional alloy, AM30-F10.1007/s11837-013-0830-x ↗
58. Dynamic testing at high strain rates of an ultrafine-grained magnesium alloy processed by ECAP10.1016/j.msea.2009.03.032 ↗
59. Rate-dependent hardening due to twinning in an ultrafine-grained magnesium alloy10.1016/j.actamat.2011.12.002 ↗
60. Mechanical behavior and microstructural evolution of a Mg AZ31 sheet at dynamic strain rates10.1016/j.actamat.2010.01.029 ↗
61. Deformation and fracture during equal channel angular pressing of AZ31 magnesium alloy10.1016/j.msea.2007.09.063 ↗
62. A critical assessment of high-temperature dynamic mechanical testing of metals10.1016/j.ijimpeng.2008.05.004 ↗
63. Microhardness mapping and the hardness-yield strength relationship in high-pressure diecast magnesium alloy AZ9110.1016/j.msea.2005.04.042 ↗
64. On the relationship between Vickers hardness and yield stress in Al-Zn-Mg-Cu alloys10.1016/j.msea.2015.02.073 ↗
65. The principles of the fiber reinforcement of metals10.1179/095066065790138357 ↗
66. Effect of deformation temperature on Hall–Petch relationship registered for polycrystalline magnesium10.1016/S0167-577X(03)00410-5 ↗
67. Enhanced ductility in high-strength fine-grained magnesium and magnesium alloy sheets processed via multi-pass rolling with lowered temperature
68. Plastic deformation behavior of Mg89Zn4Y7 extruded alloy composed of long-period stacking ordered phase10.1016/j.intermet.2010.02.011 ↗
69. Strain partitioning in dual-phase steels containing tempered martensite10.1016/j.msea.2014.05.078 ↗
70. Heterogeneous materials: a new class of materials with unprecedented mechanical properties10.1080/21663831.2017.1343208 ↗
71. Hardening evolution of AZ31B Mg sheet10.1016/j.ijplas.2006.03.005 ↗
72. Influence of grain size on the compressive deformation of wrought Mg-3Al-1Zn10.1016/j.actamat.2004.07.015 ↗
73. Origin of the twinning to slip transition with grain size refinement, with decreasing strain rate and with increasing temperature in magnesium10.1016/j.actamat.2015.01.032 ↗
74. The influence of grain size and strain rate on the mechanical behavior of pure magnesium10.1007/s10853-015-9612-x ↗
75. Evidence for exceptional low temperature ductility in polycrystalline magnesium processed by severe plastic deformation10.1016/j.actamat.2016.09.054 ↗