journal article·2019-04Open access

The valuation of microstructural evolution in a thermo-mechanically processed transformation-twinning induced plasticity steel during strain hardening

H. Eskandari Sabzi, A. Zarei-Hanzaki, A. Kaijalainen, A. Kisko

Abstract

Abstract The successive evolution of martensitic transformation, twining and dislocation substructure formation in a transformation-twinning induced plasticity steel during room temperature straining was studied in the present work. This was materialized through microstructural observations and micro-texture examinations utilizing the electron backscattered diffraction method. To evaluate the strain hardening behaviour of the thermomechanically processed steel, tensile testing procedure to different strains at ambient temperature was practiced. The results indicated that the dislocation slip, mechanical twinning, and deformation induced ɛ/α′-martensite formation were involved as the deformation mechanisms. At the early stages of deformation, the dynamic formation of dislocation substructure, strain induced ɛ-martensite and twins from austenite played the main role in the observed work hardening behaviour. Furthermore, the results demonstrated that the formation of α′-martensite was the dominant deformation mechanism at higher deformation levels. The corresponding texture analysis indicated to a double fibre texture formation, with a relatively stronger at lower strains and a stronger partial fibre parallel to tensile axis at higher strains. However, in the latter, the Cube, A and Goss Twin (GT)-type textures were dominated. Decreasing of the Goss and S components were attributed to the preferential transformation of austenite to α′- and ɛ-martensites, respectively. The presence of GT component even at higher strains approved the participation of deformation induced twinning as a dominant deformation mechanism up to failure.
Source: openaire · Quality: candidate unverified · Source record ↗

Research context

OpenAlex topics: Microstructure and Mechanical Properties of Steels · Metal Alloys Wear and Properties · Metallurgy and Material Forming

SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.

References (41)

Show source-provided references
1. Effect of thermo-mechanical processing on texture evolution in austenitic stainless steel 316L10.1016/j.matchar.2014.10.006 ↗
2. Microstructural development and deformation mechanisms during cold rolling of a medium stacking fault energy TWIP steel10.1016/j.jmst.2012.11.002 ↗
3. Transformation and twinning induced plasticity in an advanced high Mn austenitic steel processed by martensite reversion treatment10.1016/j.msea.2017.03.109 ↗
4. High strength Fe-Mn-(Al, Si) TRIP/TWIP steels development - properties - application10.1016/S0749-6419(00)00015-2 ↗
5. Strain hardening behavior of a TRIP/TWIP steel with 18.8% Mn10.1016/j.msea.2010.10.040 ↗
6. Crystallographic orientation dependence of ε martensite transformation during tensile deformation of polycrystalline 30% Mn austenitic steel10.1016/j.msea.2013.03.071 ↗
7. The influence of aluminum on hot deformation behavior and tensile properties of high-Mn TWIP steels10.1016/j.msea.2007.02.074 ↗
8. Kinetics of deformation processes in high-alloyed cast transformation- induced plasticity/twinning-induced plasticity steels determined by acoustic emission and scanning electron microscopy: influence of austenite stability on deformation mechanisms10.1016/j.actamat.2013.01.016 ↗
9. a Asghari, In situ identification of elastic – plastic strain distribution in a microalloyed transformation induced plasticity steel using digital image correlation10.1016/j.optlaseng.2013.09.009 ↗
10. Twinning and martensite in a 304 austenitic stainless steel10.1016/j.msea.2012.05.080 ↗
11. The prediction of hot deformation behavior in Fe – 21Mn – 2. 5Si – 1. 5Al transformation-twinning induced plasticity steel10.1016/j.msea.2012.06.014 ↗
12. Temperature dependence of intersection reactions of É martensite plates in an Fe-30Mn-4Si-2Al TRIP/TWIP steel10.1016/j.jallcom.2011.12.109 ↗
13. Control of strain hardening behavior in high-mn austenitic steels10.1007/s40195-014-0084-9 ↗
14. Single crystal elastic constants of high-manganese transformation- and twinning-induced plasticity steels determined by a new method utilizing nanoindentation10.1016/j.msea.2013.04.049 ↗
15. Influence of austenitic orientation on martensitic transformations in a compressed high manganese steel10.1016/j.jallcom.2011.05.015 ↗
16. The deformation of metals under small stresses during phase transformations
17. The orientation dependence of γ-α′ martensitic transformation in austenitic stainless steel single crystals with low stacking fault energy10.1016/j.msea.2006.12.204 ↗
18. Deformation behavior and microstructure/texture evolution of an annealed 304 AISI stainless steel sheet. Experimental and micromechanical modeling10.1016/j.ijplas.2006.07.002 ↗
19. Transformation potential predictions for the stress-induced austenite to martensite transformation in steel10.1016/j.actamat.2009.08.059 ↗
20. A model of stress induced martensitic transformation in Fe–Ni–C alloy10.1016/S0921-5093(99)00349-4 ↗
21. The effects of bimodal grain size distributions on the work hardening behavior of a TRansformation-TWinning induced plasticity steel10.1016/j.msea.2016.09.085 ↗
22. Formation of shear bands and strain-induced martensite during plastic deformation of metastable austenitic stainless steels10.1016/j.actamat.2007.07.015 ↗
23. Microstructure and texture evolution during cold rolling and annealing of a high Mn TWIP steel10.1016/j.actamat.2008.11.036 ↗
24. dual-phase high-entropy alloy: grain size and phase fraction effects on deformation behavior10.1016/j.actamat.2017.03.069 ↗
25. Correlating the microstructure to mechanical properties and wear behavior of an accumulative back extruded Al-Mg 2 Si in-situ composite10.1016/j.triboint.2017.05.034 ↗
26. Influence of cold rolling reduction on microstructure and mechanical properties of twip steel10.1016/S1006-7191(08)60008-3 ↗
27. Dislocation and twin substructure evolution during strain hardening of an Fe-22 wt% Mn-0.6 wt% C TWIP steel observed by electron channeling contrast imaging10.1016/j.actamat.2011.07.009 ↗
28. Texture and anisotropy, report10.1088/0034-4885/67/8/R02 ↗
29. ASTM, Astm E8, Annu. B. ASTM Stand. i, 2008.
30. Microstructure and texture evolution in a twinning-induced-plasticity steel during uniaxial tension10.1016/j.actamat.2013.01.051 ↗
31. Electron backscatter and X-ray diffraction studies on the deformation and annealing textures of austenitic stainless steel 310S10.1016/j.matchar.2016.11.019 ↗
32. Synthesis and stability of the austenite phase in mechanically alloyed Fe–Cr–Ni alloys10.1016/j.matlet.2016.10.084 ↗
33. Investigation of phase transformations in high-alloy austenitic TRIP steel under high pressure (up to 18 GPa) by in situ synchrotron X-ray diffraction and scanning electron microscopy10.1007/s11661-015-3082-2 ↗
34. A microstructure-based analysis for transformation induced plasticity and mechanically induced martensitic transformation10.1016/j.msea.2007.08.022 ↗
35. α′-martensite formation in deep-drawn Mn-based TWIP steel10.1007/s10853-012-6345-y ↗
36. Stacking fault energy and plastic deformation of fully austenitic high manganese steels: effect of Al addition10.1016/j.msea.2010.02.058 ↗
37. Understanding martensite and twin formation in austenitic steels: a model describing TRIP and TWIP effects10.1016/j.actamat.2017.02.004 ↗
38. Kinetics of strain-induced martensitic nucleation10.1007/BF02672301 ↗
39. Stacking faults and fcc (γ)→ hcp (ϵ) transformation in 188-type stainless steel10.1016/0001-6160(72)90104-6 ↗
40. The dependence of rolling texture on stacking fault energy10.1016/0001-6160(64)90182-8 ↗
41. Rolling textures of pure nickel, nickel-iron and nickel-cobalt alloys10.1016/0956-7151(95)90169-8 ↗