Microstructural evolution of pure copper subjected to friction sliding deformation at room temperature
Source abstract
Abstract
Abstract Samples of commercial oxygen-free high conductivity Cu (99.9% purity) have been deformed at room temperature using a rapid platen friction sliding deformation (PFSD) process, under conditions of high friction and relatively large applied load. The microstructural evolution of the surface layers during PFSD over sliding distances from 7 mm to 242 mm has been characterized and analyzed. The process results in the development of a gradient nanostructure, extending to increasing depths with increasing sliding distance. After a sliding distance of 242 mm the microstructure consists of a 15–20 µm layer of nanoscale lamellae at the top surface, with a sharp transition to a layer consisting of fine deformed grains, with a smooth transition to deformed material below this. Micro-hardness measurements of the nanoscale lamellae and fine deformed grains reveal values of ≈1.85 GPa and 1.2–1.5 GPa, respectively. Analysis of the microstructural evolution suggests that the hardening of the surface layers results in a transfer of shear strain to deeper volumes, enhancing the efficiency of the PFSD process.
Source: openaire · Quality: candidate unverified · Source record ↗
Research context
OpenAlex topics: Microstructure and mechanical properties · Aluminum Alloys Composites Properties · High-Velocity Impact and Material Behavior
SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.
References (32)
Show source-provided references
1. Lu · Mater. Sci. Eng. A · 2004 · 375 · 3810.1016/j.msea.2003.10.261 ↗
2. Tao · Mater. Sci. Forum · 2008 · 579 · 9110.4028/www.scientific.net/MSF.579.91 ↗
3. Li · Scr. Mater. · 2008 · 59 · 54610.1016/j.scriptamat.2008.05.003 ↗
4. Liu · Science · 2013 · 342 · 33710.1126/science.1242578 ↗
5. Hughes · J. Mater. Eng. Perform. · 1994 · 3 · 45910.1007/BF02645312 ↗
6. Hughes · Wear · 1995 · 181 · 45810.1016/0043-1648(95)90159-0 ↗
7. Zhang · Mater. Sci. Eng. A · 2014 · 607 · 35110.1016/j.msea.2014.03.089 ↗
8. Wang · Acta Mater. · 2006 · 54 · 528110.1016/j.actamat.2006.07.013 ↗
9. Zhang · Acta Mater. · 2012 · 60 · 593310.1016/j.actamat.2012.07.037 ↗
10. Wang · Mater. Sci. Eng. A · 2003 · 352 · 14410.1016/S0921-5093(02)00870-5 ↗
11. Zhang · Wear · 2006 · 260 · 94210.1016/j.wear.2005.06.010 ↗
12. Sun · Surf. Coat. Technol. · 2008 · 202 · 285910.1016/j.surfcoat.2007.10.025 ↗
13. Shi · Key Eng. Mater. · 2008 · 384 · 32110.4028/www.scientific.net/KEM.384.321 ↗
14. Fang · Science · 2011 · 331 · 158710.1126/science.1200177 ↗
15. Wu · Proc. Natl. Acad. Sci. USA · 2014 · 111 · 719710.1073/pnas.1324069111 ↗
16. Hughes · Phys. Rev. Lett. · 2001 · 87
17. Hughes · Phys. Rev. Lett. · 2014 · 11210.1103/PhysRevLett.112.135504 ↗
18. Liu · Acta Mater. · 1998 · 46 · 581910.1016/S1359-6454(98)00229-8 ↗
19. Hansen · Philos. Trans. R. Soc. Lond. A · 1999 · 357 · 144710.1098/rsta.1999.0384 ↗
20. Delannay · Acta Mater. · 2001 · 49 · 244110.1016/S1359-6454(01)00150-1 ↗
21. Yao · Wear · 2012 · 294 · 43810.1016/j.wear.2012.07.008 ↗
22. H. Magnusson, K. Frisk, Self-diffusion and Impurity Diffusion of Hydrogen, Oxygen, Sulphur and Phosphorus in Copper, Swedish Nuclear Fuel and Waste Management Co. Technical Report TR-13-24, Stockholm, 2013
23. Wang · Acta Mater. · 2010 · 58 · 237610.1016/j.actamat.2009.12.024 ↗
24. Hohenwarter · Mater. Sci. Eng. A · 2012 · 540 · 8910.1016/j.msea.2012.01.089 ↗
25. Edalati · Mater. Sci. Eng. A · 2013 · 559 · 50610.1016/j.msea.2012.08.132 ↗
26. Blum · Mater. Sci. Eng. A · 2011 · 528 · 862110.1016/j.msea.2011.08.010 ↗
27. Gazder · Mater. Sci. Eng. A · 2006 · 415 · 12610.1016/j.msea.2005.09.065 ↗
28. Mishin · Mater. Sci. Eng. A · 2003 · 342 · 32010.1016/S0921-5093(02)00311-8 ↗
29. Molodova · Mater. Sci. Eng. A · 2007 · 460 · 20410.1016/j.msea.2007.01.042 ↗
30. Tsuji · Adv. Eng. Mater. · 2003 · 5 · 33810.1002/adem.200310077 ↗
31. Yu · Mater. Res. Lett. · 2014 · 2 · 16010.1080/21663831.2014.886308 ↗
32. Renk · Acta Mater. · 2014 · 77 · 40110.1016/j.actamat.2014.06.010 ↗