journal article·2017-05

Effect of SFE on tensile and fatigue behavior of ultrafine grained Cu-Zn and Cu-Al alloys developed by cryo-rolling/forging

S.M. Dasharath, Sumit Ghosh, Suhrit Mula

Publisher page

Abstract

Abstract An attempt has been made to investigate the high cycles fatigue behavior of the ultrafine grained (UFG) low SFE Cu-Zn and Cu-Al alloys processed through cryorolling/cryoforging followed by short-annealing. The samples (CRed Cu-9.6% Zn, CFed Cu-9.6% Zn & Cu-4.5% Al, and CRed+short-annealed (225 °C) Cu-4.5% Al), which showed better combinations of YS, ductility and fracture toughness, have been selected to investigate their fatigue characteristics. High cycle fatigue strength of the UFG alloys was found to be consistent in accordance with the static mechanical properties of the corresponding sample. For example, the CFed Cu-4.5% Al alloy samples showed superior fatigue strength along with the best combination of YS, ductility and fracture toughness as compared to that of the other samples. The improved fatigue strength of the alloys has been discussed in the light of effect of low SFE, complex and unique microstructural constituents developed by cryodeformation and role of static mechanical properties of the corresponding sample. TEM analysis after fatigue tests and fractography analysis near to fracture zones corroborated well in explaining the improvement of fatigue life of the UFG alloys.
Source: openaire · Quality: candidate unverified · Source record ↗

Research context

OpenAlex topics: Microstructure and mechanical properties · Surface Treatment and Residual Stress · Metal Alloys Wear and Properties

SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.

References (27)

Show source-provided references
1. Simultaneously increasing the ductility and strength of ultra-fine-grained pure copper10.1002/adma.200601472 ↗
2. Mechanical properties and fracture mechanisms of ultrafine grained Cu-9.6% Zn alloy processed by multiaxial cryoforging10.1016/j.msea.2016.08.086 ↗
3. Microstructural evolution and mechanical properties of low SFE Cu-Al alloys processed by cryorolling followed by short-annealing10.1016/j.matdes.2016.03.095 ↗
4. Dieter · 1988 · 1
5. Enhanced cyclic deformation responses of ultrafine-grained Cu and nanocrystalline Cu–Al alloys10.1016/j.actamat.2014.04.053 ↗
6. Cyclic response of fine grain 5056 Al-Mg alloy processed by equal channel angular pressing10.1016/S0921-5093(00)01682-8 ↗
7. Fatigue properties of 5056 Al_Mg alloy produced by equal channel angular pressing10.1016/S0965-9773(99)00392-X ↗
8. Fatigue and microstructure of ultrafine grained metals produced by severe plastic deformation10.1016/j.scriptamat.2004.05.012 ↗
9. Optimizing the fatigue strength of ultrafine-grained Cu-Zn alloys10.1016/j.msea.2016.04.076 ↗
10. S.M. Dasharath, S. Mula, Mechanical properties of UFG low SFE Cu-Zn and Cu-Al alloys pocessed by cryo-rolling/forging, Ph.D. thesis, IIT Roorkee, 2017, pp. 1–164.
11. Study on cryorolled Al–Cu alloy using X-ray diffraction line profile analysis and evaluation of strengthening mechanisms10.1016/j.matdes.2013.05.095 ↗
12. Strain hardening regimes and microstructural evolution during large strain compression of low stacking fault energy fcc alloys that form deformation twins10.1007/s11661-997-0109-3 ↗
13. Anneal hardening of a nanostructured Cu–Al alloy processed by high-pressure torsion and rolling10.1016/j.msea.2015.01.055 ↗
14. Deformation twins and related softening behavior in nanocrystalline Cu–30% Zn alloy10.1016/j.actamat.2012.02.036 ↗
15. Microstructural evolution and mechanical properties of Cu–Al alloys subjected to equal channel angular pressing10.1016/j.actamat.2008.12.002 ↗
16. Strain hardening regimes and microstructural evolution during large strain compression of low stacking fault energy fcc alloys that form deformation twins10.1007/s11661-997-0109-3 ↗
17. Formation of nanostructured surface layer on AISI 304 stainless steel by means of surface mechanical attrition treatment10.1016/S1359-6454(02)00594-3 ↗
18. Influence of stacking-fault energy on the accommodation of severe shear strain in Cu-Al alloys during equal-channel angular pressing10.1557/jmr.2009.0426 ↗
19. Nanoscale structural refinement via deformation twinning in face-centered cubic metals10.1016/j.scriptamat.2009.02.008 ↗
20. Concurrent high strength and high ductility in isotropic bulk Cu–Al alloy with three-dimensional nano-twinned structure10.1016/j.jallcom.2011.11.075 ↗
21. The criteria for microstructure evolution of Cu and Cu-Al alloys induced by cyclic loading10.1016/j.msea.2016.04.069 ↗
22. Mechanical properties and fracture behavior of an ultrafine-grained Al-20wt% Si alloy10.1007/s11661-005-1003-5 ↗
23. Plastic deformation and fracture of ultrafine-grained Al–Mg alloys with a bimodal grain size distribution10.1016/j.actamat.2005.11.044 ↗
24. Improvement of high-cycle fatigue life in a 6061 Al alloy produced by equal channel angular pressing10.1016/S0921-5093(02)00010-2 ↗
25. Comparison of fatigue cracking possibility along large- and low-angle grain boundaries10.1016/S0921-5093(00)00796-6 ↗
26. Suresh · 1998 · 1
27. Effects of dislocation slip mode on high-cycle fatigue behavior of ultrafine-grained Cu–Zn alloy processed by equal-channel angular pressing10.1016/j.scriptamat.2012.10.036 ↗