journal article·2021-08

Effect of friction stir processing and subsequent annealing on microstructure and mechanical properties of a metastable β-Zr alloy

Shuo Li, Baifeng Luan, Zhongni Liao, Zhe Liu, Linhua Chu, Shuwen Wen, K.L. Murty, Qing Liu

Publisher page

Abstract

Abstract In this work, an effective method to improve the local mechanical properties of β-ZrTiAlV alloy via friction stir processing (FSP) was proposed. A good strength-ductility synergy with high yield strength (896 MPa) and elongation (18.3%) was achieved in the FSPed alloy compared to that of the base material (BM) with low elongation (2.9%) owing to the grain refinement by dynamic recrystallization (DRX) during FSP and the transformation induced plasticity (TRIP) effect caused by deformation-induced α′ martensite transformation. Moreover, FSPed alloy can be further strengthened by annealing treatment. A higher yield strength (1003 MPa) was obtained following 650 °C anneal while a higher ultimate tensile strength (1276 MPa) was acquired in 600 °C annealed samples. The microstructure-properties relationship and underlying deformation mechanisms were also investigated.
Source: openaire · Quality: candidate unverified · Source record ↗

Research context

OpenAlex topics: Advanced materials and composites · Titanium Alloys Microstructure and Properties · Aluminum Alloys Composites Properties

SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.

References (47)

Show source-provided references
1. Texture development and anisotropic deformation of zircaloys10.1016/j.pnucene.2005.09.011 ↗
2. Effect of predeformation on microstructural evolution of a Zr alloy during 550-700°C aging after β quenching10.1016/j.actamat.2013.02.001 ↗
3. Reassessment of oxidation-induced amorphization and dissolution of Nb precipitates in Zr-Nb nuclear fuel cladding tubes10.1016/j.actamat.2017.01.032 ↗
4. Achieving high strength and toughness in a Zr-2.3Nb alloy by the formation of duplex microstructure10.1016/j.matdes.2012.04.012 ↗
5. Formation of duplex microstructure in Zr-2.3Nb alloy and its plastic behaviour at various strain rates10.1016/j.ijplas.2013.08.013 ↗
6. Microstructure and mechanical properties of hot-rolled ZrTiAlV alloys10.1016/j.msea.2011.10.053 ↗
7. Structural evolution and mechanical properties of Zr-45Ti-5Al-3V alloy by heat treatments10.1016/j.msea.2012.02.003 ↗
8. Influence of the high pressure torsion die geometry on the allotropic phase transformations in pure Zr10.1016/j.msea.2010.02.066 ↗
9. High strength and ductility in multimodal-structured Zr10.1016/j.matdes.2011.08.002 ↗
10. Investigation of structure, phase composition, and mechanical properties of Zr-2.5% Nb alloy after ECAP10.1016/j.matlet.2016.01.148 ↗
11. Effect of annealing on structural and phase transformations and mechanical properties of ultrafine-grained E125 zirconium alloy obtained by high-pressure torsion10.1016/j.matlet.2017.06.107 ↗
12. Friction stir welding and processing10.1016/j.mser.2005.07.001 ↗
13. Friction-stir welding and processing of Ti-6Al-4V titanium alloy: a review10.1016/j.jmst.2017.10.018 ↗
14. Achieving ultrafine dual-phase structure with superior mechanical property in friction stir processed plain low carbon steel10.1016/j.msea.2013.03.033 ↗
15. Microstructure and mechanical properties of friction stir processed Cu with an ideal ultrafine-grained structure10.1016/j.matchar.2016.10.009 ↗
16. Achieving an excellent strength-ductility synergy in Zircaloy-4 by FSW with rapid cooling10.1080/02670836.2017.1320861 ↗
17. Microstructure, texture evolution and mechanical properties of pure Ti by friction stir processing with slow rotation speed10.1016/j.matchar.2018.12.006 ↗
18. Microstructural refinement and property enhancement of cast light alloys via friction stir processing10.1016/j.scriptamat.2007.09.062 ↗
19. Microstructural studies of friction stir welded Zircaloy-410.1016/j.scriptamat.2012.04.029 ↗
20. Twinning behaviors and grain refinement mechanisms during friction stir processing of Zr alloy10.1016/j.matchar.2020.110277 ↗
21. Microstructures and mechanical properties of friction stir welded joints of Zr-Ti alloy10.1179/1362171814Y.0000000229 ↗
22. Microstructural and mechanical properties of a beta-type titanium alloy joint fabricated by friction stir welding10.1016/j.msea.2017.11.006 ↗
23. Investigation of early stage deformation mechanisms in a metastable β titanium alloy showing combined twinning-induced plasticity and transformation-induced plasticity effects10.1016/j.actamat.2013.07.019 ↗
24. The effects of increasing deformation strain on the microstructural evolution of a metastable β-Zr alloy10.1016/j.jallcom.2019.05.334 ↗
25. {332}<113> Twinning system selection in a β-type Ti-15Mo-5Zr polycrystalline alloy10.1016/j.msea.2013.04.119 ↗
26. A new titanium alloy with a combination of high strength, high strain hardening and improved ductility10.1016/j.scriptamat.2014.09.005 ↗
27. Evidence for deformation-induced phase transformation in a high Sn content zirconium alloy10.1016/j.actamat.2018.09.034 ↗
28. Changeable Young's modulus with large elongation-to-failure in β-type titanium alloys for spinal fixation applications10.1016/j.scriptamat.2014.03.014 ↗
29. Anisotropic pitting of single-phase β-Zr alloy and isotropic pitting of α+β double-phase Zr alloy10.1016/j.corsci.2017.08.006 ↗
30. Tailoring elastic admissible strain of TiZr alloy by cold rolling deformation10.1016/j.jallcom.2018.11.388 ↗
31. Abnormal martensitic transformation of high Zr-containing Ti alloys10.1016/j.jallcom.2014.07.041 ↗
32. Development of grain structure during friction stir welding of pure titanium10.1016/j.actamat.2009.06.020 ↗
33. Stacking-fault energy, mechanical twinning and strain hardening of Fe-18Mn-0.6C-(0, 1.5)Al twinning-induced plasticity steels during friction stir welding10.1016/j.actamat.2018.02.004 ↗
34. Fabrication of high-quality Ti joint with ultrafine grains using submerged friction stirring technology and its microstructural evolution mechanism10.1016/j.actamat.2018.12.059 ↗
35. A review of dynamic recrystallization phenomena in metallic materials10.1016/j.matdes.2016.09.012 ↗
36. Dynamic and post-dynamic recrystallization under hot, cold and severe plastic deformation conditions10.1016/j.pmatsci.2013.09.002 ↗
37. Elucidation of microstructural evolution of beta-type titanium alloy joint during friction stir welding using liquid CO2 cooling10.1016/j.matchar.2018.09.005 ↗
38. Microstructural evolution of pure copper during friction-stir welding10.1080/14786435.2015.1006293 ↗
39. Deformation mechanism and mechanical properties of a thermomechanically processed β Ti-28Nb-35.4Zr alloy10.1016/j.jmbbm.2017.11.025 ↗
40. Mechanical properties and deformation mechanisms of Ti-3Al-5Mo-4.5 V alloy with varied β phase stability10.1016/j.jmst.2018.04.004 ↗
41. A multi-deformation mechanisms assisted metastable β-ZrTiAlV alloy exhibits high yield strength and high work hardening rate10.1016/j.jallcom.2019.152642 ↗
42. Deformation mechanisms in a metastable beta titanium twinning induced plasticity alloy with high yield strength and high strain hardening rate10.1016/j.actamat.2018.04.035 ↗
43. Microstructure evolution and superelastic behavior in Ti-35Nb-2Ta-3Zr alloy processed by friction stir processing10.1016/j.actamat.2017.03.079 ↗
44. Microstructure evolution and electrochemical properties of TiO2/Ti-35Nb-2Ta-3Zr micro/nano-composites fabricated by friction stir processing10.1016/j.matdes.2019.107680 ↗
45. Tensile and superelastic behaviors of Ti-35Nb-2Ta-3Zr with gradient structure10.1016/j.matdes.2020.108961 ↗
46. The influence of β phase stability on deformation mode and compressive mechanical properties of Ti-10V-3Fe-3Al alloy10.1016/j.actamat.2014.10.043 ↗
47. Influence of α morphology and volume fraction on the stress-induced martensitic transformation in Ti-10V-2Fe-3Al10.1016/j.msea.2011.03.107 ↗