The toughening mechanisms of microstructural variation and Ni addition in direct-cooled microalloyed ferrite-pearlite steels
Source abstract
Abstract
Abstract The toughening mechanisms of microstructural variation and Ni addition were investigated in two direct-cooled microalloyed ferrite-pearlite steels by using the U-notched Charpy tests. Results show that the impact toughness of the low Ni steel decreases dramatically from 110 J to 20 J when the prior austenite grain size increases from 10 µm to 37 µm, and then stays unchanged as the prior austenite grain size continues increasing from 37 µm to 90 µm. When the prior austenite grains are finer than 37 µm, the cleavage fracture is much postponed and the area of ductile fracture is much enlarged by the significantly improved ability to perform plastic deformation. When the prior austenite grains are coarse, the energy absorbed by cleavage, which is the main mode of fracture, conforms to the Griffith type equation and is much less compared to that consumed by ductile fracture, leading to the low impact toughness. The cumulative effect of ferrite content and pearlite interlamellar spacing on impact toughness is not obvious, because their influences are contradictory as the cooling rate is raised. There is a steady enhancement of about 20 J in impact toughness of the high Ni steel compared to the low Ni steel, when the austenite grain size exceeds about 37 µm. The area of ductile fracture is enlarged by the increased dislocation mobility in high Ni steel, resulting in the improvement of impact toughness. It is difficult to refine the prior austenite grain size to less than 37 µm of microalloyed ferrite-pearlite steels through optimizing forging and cooling process. However, small amount of Ni addition is beneficial to the impact toughness and does not increase the cost significantly.
Source: openaire · Quality: candidate unverified · Source record ↗
Research context
OpenAlex topics: Microstructure and Mechanical Properties of Steels · Hydrogen embrittlement and corrosion behaviors in metals · Fatigue and fracture mechanics
SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.
References (21)
Show source-provided references
1. Cleavage initiation in Ti–V–N and V–N microalloyed ferritic–pearlitic forged steels10.1016/S0921-5093(00)00803-0 ↗
2. Effect of tempering on microstructure and mechanical properties of a non-quenched bainitic steel10.1016/j.msea.2010.02.010 ↗
3. Microstructures and properties of direct-cooled microalloy forged steels10.1016/S0924-0136(01)00792-0 ↗
4. The process of crack initiation and effective grain size for cleavage fracture in pearlitic eutectoid steel10.1007/BF02811698 ↗
5. Some aspects of the structure-property relationships in high-C ferrite-pearlite steels
6. The role of microstructure on the strength and toughness of fully pearlitic steels10.1007/BF02656606 ↗
7. Characterization of transition behavior in SA508 Gr.4N Ni–Cr–Mo low alloy steels with microstructural alteration by Ni and Cr contents10.1016/j.msea.2011.09.012 ↗
8. Weld metal impact toughness of electron beam welded 9% Ni steel10.1023/A:1004890027527 ↗
9. Effect of nickel and molybdenum additions on weld metal toughness in a submerged arc welded HSLA line-pipe steel10.1016/j.jmatprotec.2005.10.028 ↗
10. Microstructural characterization, strengthening and toughening mechanisms of a quenched and tempered steel: effect of heat treatment parameters10.1016/j.msea.2017.09.062 ↗
11. Micromechanism of decrease of impact toughness in coarse-grain heat-affected zone of HSLA steel with increasing welding heat input10.1007/s11661-015-2916-2 ↗
12. Cleavage initiation in steel: competition between large grains and large particles10.1016/j.msea.2012.11.019 ↗
13. Effect of normalizing temperature on microstructure and mechanical properties of a Nb-V microalloyed large forging steel10.1016/j.msea.2016.06.059 ↗
14. Statistical scatter in the fracture toughness and Charpy impact energy of pearlitic steel10.1016/j.msea.2007.08.079 ↗
15. Crack nucleation in crystalline solids10.1179/msc.1967.1.1.56 ↗
16. Cleavage fracture in pearlitic eutectoid steel10.1007/BF02666667 ↗
17. The effect of alloying elements and microstructure on the strength and fracture resistance of pearlitic steel10.1007/BF02645816 ↗
18. Effect of carbide distribution on the grain refinement in the steel for large‐size bearing ring10.1002/srin.201500212 ↗
19. Effects of grain size on fracture toughness in transition temperature region of Mn–Mo–Ni low-alloy steels10.1016/S0921-5093(03)00344-7 ↗
20. Krauss · 2015
21. The limits of strength and toughness in steel10.2355/isijinternational.41.599 ↗