Mechanical and tribological behavior of severely plastic deformed Al6061 at cryogenic temperatures
Source abstract
Abstract
Abstract In this research, Al6061 alloy was severely cryorolled up to 85% thickness reduction to study the effect of the cryorolling process on its microstructural, mechanical and tribological properties. The cryorolled Al6061 alloy was characterized by using scanning and transmission electron microscopies (SEM, TEM), X-ray diffraction (XRD) analysis, and microhardness, tensile, nano-indentation, and sliding wear tests. An improved tensile strength of the cryorolled Al6061 alloy after aging heat treatment (the CR+PA sample, 357 MPa) was observed as compared to the cryorolled sample (the CR sample, 292 MPa) and the solution treated sample (the ST sample, 150 MPa). The improved strength of the cryorolled alloy is due to the accumulation of dislocation density as a result of deformation at cryogenic temperatures and ultrafine-grained microstructure after aging heat treatment. Furthermore, in the CR sample, due to the high dislocation density and rapid atomic diffusion along dislocations, nano-sized β′ and β″ precipitates were formed. Also, the mentioned microstructural features resulted in an increase in the hardness of the CR+PA sample as shown by microhardness and nano-indentation tests. An increase in the wear resistance of Al6061 alloy as a result of cryorolling and aging was also observed. The wear mass loss for the Al6061-T6, CR, and CR+PA samples in 500 m were 63.6, 66.2 and 39.5 mgr, respectively. According to the evaluation of wear tracks and debris, for all samples, the adhesive and abrasive mechanisms were the dominant wear mechanisms.
Source: openaire · Quality: candidate unverified · Source record ↗
Research context
OpenAlex topics: Metal Alloys Wear and Properties · Microstructure and mechanical properties · Aluminum Alloys Composites Properties
SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.
References (33)
Show source-provided references
1. Phase relations and precipitation in Al-Mg-Si alloys with Cu additions10.1016/S0079-6425(03)00031-8 ↗
2. Precipitation hardening processes in an Al–0.4%Mg–1.3%Si–0.25%Fe aluminum alloy10.1016/S0921-5093(00)01814-1 ↗
3. Precipitation kinetics and transformation of metastable phases in Al-Mg-Si alloys10.1016/j.actamat.2006.06.005 ↗
4. On the precipitation-hardening behavior of the Al-Mg-Si-Cu alloy AA6111
5. A systematic comparison of static and dynamic ageing of two Al-Mg-Si alloys10.1016/j.msea.2003.12.035 ↗
6. Hall-petch relation and boundary strengthening10.1016/j.scriptamat.2004.06.002 ↗
7. Bulk nanostructured materials from severe plastic deformation10.1016/S0079-6425(99)00007-9 ↗
8. Novel ultra-high straining process for bulk materials—development of the accumulative roll-bonding (ARB) process10.1016/S1359-6454(98)00365-6 ↗
9. Microstructural evolution over a large strain range in aluminium deformed by cyclic-extrusion–compression10.1016/S0921-5093(98)00988-5 ↗
10. Experimental parameters influencing grain refinement and microstructural evolution during high-pressure torsion10.1016/S1359-6454(02)00466-4 ↗
11. High tensile ductility in a nanostructured metal10.1038/nature01133 ↗
12. Effect of cryo-rolling and annealing on microstructure and properties of commercially pure aluminium10.1016/j.msea.2005.03.026 ↗
13. The tensile behavior and deformation microstructure of cryo-rolled and annealed pure nickel10.1016/j.msea.2005.07.045 ↗
14. Effect of annealing temperature on microstructures and mechanical properties of a 5083 Al alloy deformed at cryogenic temperature10.1016/j.scriptamat.2004.02.037 ↗
15. Development of ultrafine grained high strength Al-Cu alloy by cryorolling10.1016/j.scriptamat.2006.03.012 ↗
16. A study on the mechanical properties of cryorolled Al-Mg-Si alloy10.1016/j.msea.2007.07.024 ↗
17. Tensile and impact-toughness behaviour of cryorolled Al 7075 alloy10.1016/j.matdes.2010.09.026 ↗
18. Optimizing the strength and ductility of fine structured 2024 Al alloy by nano-precipitation10.1016/j.actamat.2007.06.043 ↗
19. Enhancement in strength and ductility of Al-Mg-Si alloy by cryorolling followed by warm rolling10.1016/j.proeng.2013.11.027 ↗
20. Effect of annealing and aging treatment on mechanical properties of ultrafine grained Al 6061 alloy10.1179/174328409X443227 ↗
21. Microstructure and mechanical properties of cryo-rolled AA6061 Al alloy10.1016/S1003-6326(16)64083-9 ↗
22. Evaluation of the tribological properties of an Al-Mg-Si alloy processed by severe plastic deformation10.1016/j.wear.2010.12.082 ↗
23. X-ray line broadening from filed aluminium and wolfram10.1016/0001-6160(53)90006-6 ↗
24. Krishna · Int. J. Adv. Manuf. Technol. · 2016 · 1
25. Microstructure of the post-ECAP aging processed 6061 Al alloys10.1016/j.msea.2007.03.074 ↗
26. Kelly · 1971
27. Meyers · 1984
28. Frost · 1982
29. Verlinden · 2007
30. Rollett · 2008
31. Nembach · 1997
32. An analysis of the strain hardening behavior of ultra-fine grain pure titanium10.1016/j.scriptamat.2006.01.034 ↗
33. Wear properties of ECAP-processed ultrafine grained Al-Cu alloys10.1016/j.msea.2010.03.057 ↗