journal article·2013-09

Distribution of Microdefects in Sheets of St1.03-12 Low-Carbon Steel in Tension at Different Rates

O. R. Hokhman, N. A. Volchok, D. Fassmann

Materials Science· Volume 49· Issue 2
Publisher page

Abstract

We study the influence of the tensile strain rate on the anisotropy of Young’s modulus, the yield strength, and damage coefficient of sheets of St1.03 12 low-carbon steel (0.06 % С, to 0.35 Mn, to 0.40 Si, and ~ 0.025 % S and P). It was established that, with increase in the strain rate from 0.0017 up to 5 mm/sec, texture transformations occur, Young’s modulus decreases, and, with decrease in the anisotropy of damages of the sheets, the yield strength and damage coefficient increase.
Source: openaire · Quality: candidate unverified · Source record ↗

Research context

OpenAlex topics: Metal Forming Simulation Techniques · Material Properties and Failure Mechanisms · Microstructure and Mechanical Properties of Steels

SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.

References (15)

Show source-provided references
1. G. A. Maugin, The Thermomechanics of Plasticity and Fracture, Cambridge University Press, Cambridge (1992).10.1017/CBO9781139172400 ↗
2. J. C. Simo and J. W. Ju, “Strain- and stress-based continuum damage models–I. Formulation,” Int. J. Solids Struct., 23, No. 7, 821–840 (1987).10.1016/0020-7683(87)90083-7 ↗
3. J. Lemaitre, A Course on Damage Mechanics, Springer, Berlin (1992).10.1007/978-3-662-02761-5 ↗
4. J. Nai, Physical Properties of Crystals: Their Representation by Tensors and Matrices, Oxford University Press (1957).
5. A. А. Lebedev, N. G. Chausov, and O. I. Marusii, “Fracture kinematics of sheet austenitic steel in the final stage of deformation,” Probl. Prochn., No. 3, 16–21 (1989).
6. V. Randle, Introduction to Texture Analysis. Macrotexture, Microtexture and Orientation Mapping, CRC Press LLC, London–New York–Washington (2000).10.1201/9781482287479 ↗
7. Yu. I. Rivlin, M. A. Korotkov, and V. N. Chernobyl’skii, Metals and Their Substitutes. A Handbook [in Russian], Metallurgiya, Moscow (1973).
8. V. A. Lubarda, “Damage tensors and crack density distribution,” Int. J. Solids Struct., 30, No. 20, 2859–2877 (1993).10.1016/0020-7683(93)90158-4 ↗
9. H. J. Bunge, Mathematische Metoden der Texturanalyse, Akademie-Verlag, Berlin (1969).
10. A. A. Bryukhanov, A. R. Gokhman, and N. I. Sologub, “Distribution of the density of poles for the isotropic plane of a cubic crystal and the anisotropy of the elastic properties of textured sheets of 12Kh18N10T austenitic steel,” Izv. Vyssh. Ucheb. Zaved., Ser. Chern. Mettalurg., No. 4, 58–61 (1988).
11. A. R. Gokhman and V. K. Zhukovskii, “Dependence of the physicomechanical properties of structural materials of electronic equipment on their textures,” Izv. Vyssh. Ucheb. Zaved. Ros. Feder., Ser. Mater. Élektr. Tekh., No. 1, 70–74 (2005).
12. A. A. Bryukhanov, А. R. Gokhman, M. Rodman, et al., “On the method of certification of rolled sheets,” Proizv. Prokat., No. 2, 32–39 (2011).
13. V. V. Panasyuk (editor), Fracture Mechanics and Strength of Materials [in Russian], Vol. 1, Naukova Dumka, Kiev (1988–1990).
14. S. Murakami and Yu. N. Radaev, “Mathematical model of the anisotropic damaged state,” Izv. Ros. Akad. Nauk, Ser. Mekh. Tverd. Tela, No. 4, 93–110 (1996).
15. H. Neuber, “Uber die Berucksichtigung der Spannungskonzentration bei Festigkeitsberechnungen,” Konstruction, 20, 245–251 (1968).