journal article·2017-11-03Open access

Analyzing the effects of powder and post-processing on porosity and properties of electron beam melted Ti-6Al-4V

Ross Cunningham, Andrea Nicolas, John Madsen, Eric Fodran, Elias Anagnostou, Michael D. Sangid, Anthony D. Rollett

Materials Research Letters· Volume 5· Issue 7

Abstract

Metal additive manufacturing techniques such as the powder-bed systems are developing as a novel method for producing complex components. This study uses synchrotron-based X-ray microtomography to investigate porosity in electron beam melted Ti-6Al-4V in the as-built and post-processed state for two different powders. The presence of gas porosity in the starting powder was shown to correlate to porosity in the as-built components. This porosity was observed to shrink after a hot isostatic press treatment, but grow following a subsequent heat treatment. Crystal plasticity simulations were used to observe the effects of various observed pore sizes on mechanical behavior under loading.
Source: openalex_inverted_index · Quality: baseline

Research context

OpenAlex topics: Additive Manufacturing Materials and Processes · Titanium Alloys Microstructure and Properties · Advanced materials and composites

SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.

Affiliations

Department of Materials Science and Engineering, Carnegie Mellon University, Pittsburgh, PA, USA

School of Aeronautics and Astronautics, Purdue University, West Lafayette, IN, USA

Northrop Grumman Aerospace Systems, Bethpage, NY, USA

Northrop Grumman Aerospace Systems, El Segundo, CA, USA

Funding

Northrop Grumman Corporation

References (35)

Show source-provided references
1. 10.1007/s11665-014-0958-z10.1007/s11665-014-0958-z ↗
2. 10.1016/j.addma.2014.08.00210.1016/j.addma.2014.08.002 ↗
3. 10.1016/j.matchar.2015.02.00810.1016/j.matchar.2015.02.008 ↗
4. 10.1007/s11837-015-1802-010.1007/s11837-015-1802-0 ↗
5. 10.1007/s11661-016-3429-310.1007/s11661-016-3429-3 ↗
6. 10.1016/j.ijfatigue.2016.06.00110.1016/j.ijfatigue.2016.06.001 ↗
7. 10.1016/S0013-7944(02)00097-810.1016/S0013-7944(02)00097-8 ↗
8. 10.1080/14786435.2015.100995810.1080/14786435.2015.1009958 ↗
9. 10.1016/j.matdes.2015.07.14710.1016/j.matdes.2015.07.147 ↗
10. 10.1016/j.jmatprotec.2014.06.00510.1016/j.jmatprotec.2014.06.005 ↗
11. 10.1016/j.actamat.2015.07.01410.1016/j.actamat.2015.07.014 ↗
12. 10.1088/0022-3727/42/2/02550310.1088/0022-3727/42/2/025503 ↗
13. 10.1016/j.scriptamat.2012.06.01510.1016/j.scriptamat.2012.06.015 ↗
14. 10.1016/j.msea.2011.06.07410.1016/j.msea.2011.06.074 ↗
15. 10.1007/s11661-999-1011-y10.1007/s11661-999-1011-y ↗
16. 10.1007/s11661-004-0013-z10.1007/s11661-004-0013-z ↗
17. 10.1016/j.actamat.2012.02.03510.1016/j.actamat.2012.02.035 ↗
18. 10.6028/jres.119.01910.6028/jres.119.019 ↗
19. Elmer JW. · Weld J · 2015 · 94 · 313
20. 10.1016/j.acme.2014.02.00310.1016/j.acme.2014.02.003 ↗
21. 10.2351/1.358231110.2351/1.3582311 ↗
22. 10.1016/j.cirp.2014.05.01110.1016/j.cirp.2014.05.011 ↗
23. 10.1016/j.ndteint.2010.06.00410.1016/j.ndteint.2010.06.004 ↗
24. 10.1007/s11837-016-2234-110.1007/s11837-016-2234-1 ↗
25. 10.1016/j.scriptamat.2016.05.00210.1016/j.scriptamat.2016.05.002 ↗
26. 10.1107/S160057751401393910.1107/S1600577514013939 ↗
27. Gaytan SM · Mater Technol Adv Perform Mater · 2009 · 24 · 180
28. 10.1016/j.actamat.2004.01.03910.1016/j.actamat.2004.01.039 ↗
29. 10.1016/j.actamat.2004.01.01910.1016/j.actamat.2004.01.019 ↗
30. 10.1016/j.ijplas.2011.12.00510.1016/j.ijplas.2011.12.005 ↗
31. 10.1016/S0045-7825(97)00218-110.1016/S0045-7825(97)00218-1 ↗
32. 10.1016/S0031-8914(34)80244-310.1016/S0031-8914(34)80244-3 ↗
33. 10.1016/j.ijplas.2008.08.00410.1016/j.ijplas.2008.08.004 ↗
34. 10.1016/j.ijplas.2006.11.00910.1016/j.ijplas.2006.11.009 ↗
35. 10.1016/j.msea.2016.03.01210.1016/j.msea.2016.03.012 ↗