journal article·2016-08-22Open access

Effect of Rapid Solidification and Addition of Cu3P on the Mechanical Properties of Hypereutectic Al-Si Alloys

Miguel Ángel Suárez-Rosales, Raúl Pinto-Segura, Elia Guadalupe Palacios-Beas, Alfredo Hernández-Herrera, José Federico Chávez-Alcalá

Materials Research· Volume 19· Issue suppl 1

Abstract

The combined processes; rapid solidification, addition of Cu3P compound and heat treatments to improve the mechanical properties of the hypereutectic Al-13Si, Al-20Si and Al-20Si-1.5Fe-0.7Mn alloys (in wt. %) was studied. Optical microscopy and scanning electron microscopy were used to characterize the microstructures. The mechanical properties were evaluated by tensile tests. It was found that the cooling rate (20-50°C/s) used to solidify the alloys plus the addition of Cu3P compound favored the formation of fine primary Si and the transformation of the Al/Si eutectic from acicular to semi-transformed morphology. The spheroidization of the Al/Si eutectic after heat treatment caused an increase in the elongation (%) compared with the as-cast alloys. Al-13Si alloy showed the highest UTS and elongation (%) values, reaching values up to 215 MPa and 9.6%, respectively. On the other hand, the Al-20Si-1.5Fe-0.7Mn alloy showed the lowest UTS (180MPa) and elongation (3.4%) values. The formation of the Fe-intermetallic compounds caused a negative effect on the mechanical properties of the Al-20Si-1.5Fe-0.7Mn alloy.
Source: openalex_inverted_index · Quality: baseline

Research context

OpenAlex topics: Aluminum Alloy Microstructure Properties · Aluminum Alloys Composites Properties · Microstructure and mechanical properties

SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.

Affiliations

Universidad Nacional Autónoma de México, Mexico

Instituto Politécnico Nacional, Mexico

References (22)

Show source-provided references
1. Review of microstructure evolution in hypereutectic Al-Si alloys and its effect on wear properties10.1007/s12666-013-0327-x ↗
2. Impact toughness in Al-12Si and Al-12Si-3Cu cast alloys-Part 1: Effect of process variables and microstructure10.1016/j.ijimpeng.2007.03.002 ↗
3. Impact toughness of an ingot hypereutectic Al-23 mass% Si alloy improved by rotary-die equal-channel angular pressing10.1016/j.msea.2005.03.009 ↗
4. Silicon morphology modification in the eutectic Al-Si alloy using mechanical mold vibration. hypereutectic Al-23 mass% Si alloy improved by rotary-die equal-channel angular pressing10.1016/j.msea.2004.09.038 ↗
5. Influence of combined grain refinement and modification on the microstructure, tensile strength and wear properties of Al-15Si, Al-15Si-4.5Cu alloys10.3139/146.111270 ↗
6. Effect of Al-P-Ti-TiC-Nd2O3 modifier on the microstructure and mechanical properties of hypereutectic Al-20 wt.%Si alloy10.1016/j.msea.2006.10.114 ↗
7. Effect of P and Sr complex modification on Si phase in hypereutectic Al-30Si alloys10.1016/j.matdes.2012.12.054 ↗
8. Effect of phosphorous, titanium-boron and titanium on thermal properties of hypereutectic aluminium-silicon alloys
9. Sb effect on micro structural and mechanical properties of rapidly solidified Al-12Si alloy10.1016/j.jallcom.2010.09.037 ↗
10. Effect of heat treatment on microstructure and tensile properties of A356 alloys10.1016/S1003-6326(11)60955-2 ↗
11. On the silicon spheroidization in Al-Si alloys10.1016/S1471-5317(03)00010-5 ↗
12. Effet des conditions de solidification sur la qualité des alliage de fonderie de A-U5 G T et A-S7 G, estimation des caractéristiques mécaniques
13. Effect of cooling rate on solidification parameters and microstructure of Al−7Si−0.3Mg−0.15Fe alloy10.1016/S1003-6326(14)63236-2 ↗
14. Solidification behavior of Al-Si-Fe alloys and phase transformation of metastable intermetallic compound by heat treatment10.1023/A:1004584415196 ↗
15. Modification of solidification microstructure in hypo- and hyper-eutectic Al-Si alloys under high-intensity ultrasonic irradiation10.1016/j.jallcom.2014.09.089 ↗
16. Study of the Al-Si-X system by different cooling rates and heat treatment10.1590/S1516-14392012005000103 ↗
17. Iron intermetallic phases in the Al corner of the Al-Si-Fe system10.1007/s11661-003-0116-y ↗
18. The effect of Mn additions on the microstructure and mechanical properties of Al-Si-Cu casting alloys10.1016/j.msea.2007.12.026 ↗
19. Effect of iron content on the formation of β-Al5FeSi and porosity in Al-Si eutectic alloys10.1016/j.jmatprotec.2008.02.073 ↗
20. Iron-Containing Intermetallic Phases in Al-Si Based Casting Alloys10.1016/j.mspro.2012.06.004 ↗
21. The mutual effect of iron and manganese on microstructure and mechanical properties of aluminum-silicon alloy
22. Fracture features of a silicon-dispersed aluminium alloy extruded from rapidly solidified powder10.1007/BF00581121 ↗